Cisco D9854i Manual

							 
 
Fault History ............................................................................................................ 315 
Log History .............................................................................................................. 316 
Appendix D Compliance 317 
Applicable Standards and Notices .................................................................................... 318 
Safety ........................................................................................................................ 318 
EMC .......................................................................................................................... 318 
Electromagnetic Compatibility Regulatory Requirements ............................... 318 
FCC Notices ............................................................................................................. 319 
Industry Canada Notice ......................................................................................... 319 
Unauthorized Modifications ................................................................................. 319 
Declaration of Conformity .................................................................................................. 320 
Index 321 
   
						

							 
  About This Manual  
78-4021470-01 Rev J xxiii 
 
About This Manual 
Objective 
This manual describes how to install, use and maintain the Cisco® D9854 Advanced 
Program Receiver. 
Note: The manual describes all available options for the D9854 receiver. Your D9854 
receiver may only have some of the features described in this manual.   
Audience 
The audience of this manual includes users (operators) and service personnel who 
are responsible for the installation, configuration, operation, monitoring and service 
of the D9854 receiver.  
Required Knowledge 
To use this documentation, the user should have a basic knowledge of the 
technology used in relation to this product. Service personnel should have 
additional skills and be familiar with cabling, electronic circuitry, and wiring 
practices. 
This manual is intended for operators who are responsible for the configuration, 
remote operation and maintenance of the D9854 receiver. 
 
  
						

							 
 
78-4021470-01 Rev J 1 
 
Overview 
This chapter provides a quick setup for your D9854 receiver. If you are 
unsure about which receiver settings to use, contact your local service 
provider for assistance.  
 
 
1 Chapter 1 
Quick Setup - Read Me First! 
In This Chapter 
 Connecting the Receiver to Other Equipment .................................... 2 
 Setting up for Network Connection ..................................................... 4 
 Quick Setup Instructions for RF Acquisition ...................................... 5 
 Assigning a Program Channel to a PE (Program Entry) ................... 7 
 ASI Out ..................................................................................................... 8 
 Setting up the HD-SDI Outputs (SDI Model, with SD/HD-SDI 
and AES outputs) .................................................................................... 9 
 Setting up the MOIP Outputs (Base Model) ..................................... 10 
 Setting the DPM Mode ......................................................................... 11  
						

							 
Chapter 1    Quick Setup - Read Me First!  
 
 
2 78-4021470-01 Rev J 
Connecting the Receiver to Other Equipment 
The following displays the rear panel of the D9854 Base Model: 
 
The following displays the rear panel of the D9854 SDI Model, with SD/HD-SDI and 
AES outputs: 
 
1 Connect the L-Band signal to RF1. 13V or 18V LNB power is only available on 
the RF1 port. The factory default setting for LNB power is OFF.  
2 Connect the ASI OUT port to an ASI device for digital tier applications. 
3 Connect the Composite Video Output to a video monitor. 
4 Connect the terminal block balanced audio outputs labeled AUDIO 1 and 
AUDIO 2 to monitoring equipment. 
5 Apply power by connecting the receiver to a power outlet. The message 
“Application Starting” will appear on the front panel. The boot process 
approximately 1 minute for the unit to initialize. When ready, the front panel 
display shows the startup screen. 
6 The Ethernet Management port does not currently provide SNMP or 
management control. It is used for software application downloads only. 
7 Connect the HD-SDI outputs (M1 and M2) to HD compatible signal processing 
equipment or HD signal monitoring equipment, if applicable.   
						

							 
 
 Connecting the Receiver to Other Equipment 
 
78-4021470-01 Rev J 3 
 
Maintenance of EMC Compliance 
The power cord (consisting of appliance coupler, flexible cord, and plug) supplied 
with this product meets the requirements for use in the country for which this 
product was purchased. In general, the power cord must be approved by an 
acceptable, accredited agency responsible for evaluation in the country where the 
product will be used.  
Double-shielded (braid/foil or braid/braid) cables should be used for all ASI I/O 
and RF inputs. Single-shield cables are acceptable for all other inputs and outputs. 
For terminal block (Alarms) I/O, no shielding is required. 
  
						

							 
Chapter 1    Quick Setup - Read Me First!  
 
 
4 78-4021470-01 Rev J 
Setting up for Network Connection 
1 Press MENU to display the Main menu.  
2 Press  to go to the Setup menu. Press SELECT. Press  twice to select the IP 
menu. Press SELECT twice to go to the IP menu. 
3 Use the  arrow keys to navigate up and down the IP menu, and the   arrow 
keys to move across the IP menu to set the IP Address, Mask and Gateway 
parameters. Use the number keys to directly enter numbers in the fields. For 
more information on keypad operation, see Keypad Convention. 
4 Press SELECT each time to save the changes. Press MENU four times to return 
to the startup screen. 
  
						

							 
 
 Quick Setup Instructions for RF Acquisition 
 
78-4021470-01 Rev J 5 
 
Quick Setup Instructions for RF Acquisition 
1 Press MENU to display the Main menu.  
2 Press  to go to the Setup menu. Press SELECT. Press to move to the TS Input 
menu. Press SELECT.   
3 To setup the ASI input port, go to step 4. To setup the RF1 input port, go to step 
5. 
4 Press SELECT three times. Press  to set the ASI port to Act (Activate). Press 
SELECT. Go to step 11. 
5 Press SELECT. Press to go to RF1. Press SELECT twice. Use  to set the RF1 
port parameter to Act (Activate). Press SELECT.   
6 Press to move to the LO1, LO2, Crossover menu. Verify these parameters for 
your application. If no change is needed, go to Step 7.  If required, you may 
modify these settings. Use to move to the parameter that you want to modify. 
Press SELECT. Use the numerical keypad to enter new frequencies. Press 
SELECT.   
7 Press five times to move to the Modulation and Rolloff menu.  Press SELECT. 
Use   to choose DVB-S or DVB-S2. Press SELECT. If DVB-S2 is used, press to 
choose Rolloff. Press SELECT. Use   to choose the value. Press SELECT.   
8 Press  to move to the Freq., Sym Rate, and FEC menu. Press SELECT.  Enter the 
RF frequency. Press SELECT. Press to move to the Sym. Rate menu. Press 
SELECT. Enter the symbol rate. Press SELECT. If DVB-S2 is used, proceed to 
step 9. If DVB-S is used, press to set up the FEC. Press SELECT. Use  to 
select AUTO. Press SELECT.   
9 Press  twice to move to the Net ID menu. Press  to choose Net ID. Press 
SELECT. Enter the value. Press SELECT.   
10 Press . Press SELECT. Use   to change the LNB power, if needed. Only the 
RF1 port is capable of providing 13V or 18V. Press SELECT.   
11 Press MENU three times. Press to move to Save & Exit. Press SELECT. Save & 
Exit will return you to the Main: Setup menu; Abandon & Exit will go back to the 
last menu accessed with the original parameters; Cancel will go back to the last 
menu accessed with changes saved.   
12 The receiver will search for the signal and display “Acquisition Successful”. It 
will find the first available channel on the network. Press MENU twice to return 
to the start-up menu.  
						

							 
Chapter 1    Quick Setup - Read Me First!  
 
 
6 78-4021470-01 Rev J 
13 If the front LED is solid green, the unit is authorized. Proceed with Assigning a 
Program Channel to a PE (Program Entry). If the front LED is flashing green, the 
unit is unauthorized. Please contact your service provider and provide the 
Tracking ID number for authorization. The Tracking ID can be found on the 
ABOUT menu. To locate the Tracking ID, press MENU, press twice, and then 
press SELECT twice. Make a note of the Tracking ID number. Press MENU three 
times to return to the startup screen.