Cisco 3560 Poe8 Manual

 
3-5
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 3      Switch Installation (8- and 12-Port Switches)
Preparing for Installation
Statement 371—Power Cable and AC Adapter
CautionTo comply with the Telcordia GR-1089 Network Equipment Building Systems (NEBS) standard for 
electromagnetic compatibility and safety, connect the ethernet cables only to intrabuilding or 
nonexposed wiring or cabling. 
CautionTo comply with the Telcordia GR-1089 NEBS standard, PoE or non-PoE 10/100/1000...

 
3-6
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 3      Switch Installation (8- and 12-Port Switches)
Preparing for Installation
Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent 
lighting fixtures. Make sure the cabling is safely away from other devices that might damage the 
cables.
For copper Ethernet ports, including 10/100 ports, 10/100/1000 ports, and 1000BASE-T 
SFP module ports, cable lengths from the switch to connected...

 
3-7
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 3      Switch Installation (8- and 12-Port Switches)
Verifying Switch Operation
Box Contents
The switch getting started guide on Cisco.com describes the box contents. If any item is missing or 
damaged, contact your Cisco representative or reseller for support.
Tools and Equipment
You need to supply a number-2 Phillips screwdriver to rack-mount the switch.
Verifying Switch Operation
Before you install the switch, power it on and...

 
3-8
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 3      Switch Installation (8- and 12-Port Switches)
Installing the Switch
Desk or Shelf Mounting
Desk or Shelf Mounting (Unsecured), page 3-8
Desk or Shelf Mounting (Secured), page 3-8
Under the Desk or Shelf Mounting, page 3-9
Desk or Shelf Mounting (Unsecured)
Step 1Locate the adhesive strip with the rubber feet in the accessory kit. 
Step 2Remove the four rubber feet from the adhesive strip, and attach them to the recessed...

 
3-9
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 3      Switch Installation (8- and 12-Port Switches)
Installing the Switch
Step 4Use a 0.144-inch (3.7 mm) or a #27 drill bit to drill a 1/2-inch (12.7 mm) hole in the three screw 
template slots.
Step 5Insert three screws in the slots on the screw template, and tighten until they touch the top of the screw 
template.
Step 6Remove the screw template from the desk or shelf.
Step 7Place the switch on the mounting screws, and slide it...

 
3-10
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 3      Switch Installation (8- and 12-Port Switches)
Installing the Switch
Figure 3-3 Installing the Mounting Screws Under a Desk or Shelf           
Step 3Peel the adhesive strip off the bottom of the screw template, and attach it to the underside of the desk or 
shelf.
Step 4Use a 0.144-inch (3.7 mm) or a #27 drill bit to drill a 1/2 inch (12.7 mm) hole in the three screw 
template slots.
Step 5Insert three screws in the slots...

 
3-11
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 3      Switch Installation (8- and 12-Port Switches)
Installing the Switch
Step 7Place the switch onto the mounting screws and slide the switch forward until it locks in place, as shown 
in Figure 3-4.
Figure 3-4 Mounting the Switch Under a Desk or Shelf          
After the switch is mounted on or under the desk or shelf:
1.(Optional) Secure the AC power cord. See “Securing the AC Power Cord” section on page 3-19.
2.Power on the...

 
3-12
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 3      Switch Installation (8- and 12-Port Switches)
Installing the Switch
Wall-Mounting (with Mounting Screws)
Mount the switch with the front panel facing down (as shown in Figure 3-5 on page 3-13 and Figure 3-6 
on page 3-14.) 
WarningRead the wall-mounting instructions carefully before beginning installation. Failure to use the 
correct hardware or to follow the correct procedures could result in a hazardous situation to...

 
3-13
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 3      Switch Installation (8- and 12-Port Switches)
Installing the Switch
Figure 3-5 Installing the Mounting Screws on a Wall             
Step 3Peel the adhesive strip off the bottom of the screw template. 
Step 4Attach the screw template to the wall.
Step 5Use a 0.144-inch (3.7 mm) or a #27 drill bit to drill a 1/2 inch (12.7 mm) hole in the three screw 
template slots.
Step 6Insert three screws in the slots on the screw...

 
3-14
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 3      Switch Installation (8- and 12-Port Switches)
Installing the Switch
Step 8Place the switch onto the mounting screws and slide it down until it locks in place, as shown 
in Figure 3-6.
Figure 3-6 Installing the Switch On a Wall         
After the switch is mounted on the wall:
1.(Optional) Secure the AC power cord. See “Securing the AC Power Cord” section on page 3-19.
2.Power on the switch. See the “Verifying Switch...