Cisco 3560 Poe8 Manual

 
2-9
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Installing the Switch
Figure 2-3 Attaching Brackets for 24-Inch Racks to a Catalyst 3560 Switch, Front Panel Forward                  
Figure 2-4 Attaching Brackets for 19-Inch Racks to a Catalyst 3560 Switch, Rear Panel Forward                     
Figure 2-5 Attaching Brackets for 24-Inch Racks to a Catalyst 3560 Switch, Rear Panel Forward                      
1Phillips...

 
2-10
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Installing the Switch
Figure 2-6 Attaching Brackets for 19-Inch Telco Racks to a Catalyst 3560 Switch               
Figure 2-7 Attaching Brackets for 24-Inch Telco Racks to a Catalyst 3560 Switch               
Mounting the Switch in a Rack
After the brackets are attached to the switch, use the four supplied number-12 Phillips machine screws 
to securely attach the brackets to...

 
2-11
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Installing the Switch
After the switch is mounted in the rack:
1.Power on the switch. See the “Verifying Switch Operation” section on page 2-6. 
2.Connect to a 10/100 or 10/100/1000 port, and run Express Setup. See the Catalyst 3560 Switch 
Getting Started Guide for instructions. To use the CLI setup program, see Appendix D, 
“Configuring the Switch with the CLI-Based Setup...

 
2-12
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Installing the Switch
Wall-Mounting
These switches wall-mount only with the front panel facing up:
Catalyst 3560-24PS, 3560-24TS-S, 3560-48PS, and 3560-48TS-S
Catalyst 3560G-24PS, 3560G-24TS, 3560G-48PS, and 3560G-48TS
These switches wall-mount with the front panel facing up or down:
Catalyst 3560V2-24PS, 3560V2-24TS, 3560V2-48PS, and 3560V2-48TS
The illustrations in this...

 
2-13
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Installing the Switch
Attaching the RPS Connector Cover
If you are not using an RPS with your switch, use the two Phillips pan-head screws to attach the 
RPS connector cover to the back of the switch, as shown in Figure 2-11.
WarningIf a redundant power system (RPS) is not connected to the switch, install an RPS connector cover on 
the back of the switch. Statement 265
Figure...

 
2-14
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Installing the Switch
Mounting the Switch on a Wall
For the best support of the switch and cables, make sure the switch is attached securely to wall studs or 
to a firmly attached plywood mounting backboard. Mount the switch with the front panel facing up, as 
shown in Figure 2-12.
See the “Wall-Mounting” section on page 2-12 for the switches that can also mount with the front...

 
2-15
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Installing and Removing SFP Modules
Table- or Shelf- Mounting
Step 1Locate the adhesive strip with the rubber feet in the mounting-kit envelope. Attach the four rubber feet 
to the bottom of the switch near the corners.
NoteDo not attach the rubber feet over the recessed screw holes on the bottom of the switch.
Step 2Place the switch on the table or shelf near an AC power...

 
2-16
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Installing and Removing SFP Modules
Installing SFP Modules into SFP Module Slots
Figure 2-13 shows an SFP module that has a bale-clasp latch. 
Figure 2-13 SFP Module with a Bale-Clasp Latch
CautionWe strongly recommend that you do not install or remove fiber-optic SFP modules with cables attached 
because of the potential damage to the cables, the cable connector, or the...

 
2-17
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Installing and Removing SFP Modules
Step 5For fiber-optic SFP modules, remove the dust plugs from the optical ports, and store them for later use.
CautionDo not remove the dust plugs from the fiber-optic SFP module port or the rubber caps from the 
fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the SFP module 
ports and cables from...

 
2-18
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Inserting and Removing the SFP Module Patch Cable
Step 5For fiber-optic SFP modules, insert a dust plug into the optical ports of the SFP module to keep the 
optical interfaces clean.
Step 6Place the removed SFP module in an antistatic bag or other protective environment.
Inserting and Removing the SFP Module Patch Cable
Step 1Attach an ESD-preventive wrist strap to your wrist...