Cisco 3560 Poe8 Manual

 
2-19
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
10/100 or 10/100/1000 Ports
10/100 or 10/100/1000 Ports
The switch 10/100 and 10/100/1000 ports configure themselves to operate at the speed of attached 
devices. If the attached ports do not support autonegotiation, you can explicitly set the speed and duplex 
parameters. Connecting devices that do not autonegotiate or that have their speed and duplex parameters 
manually set...

 
2-20
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Connecting the Switch to Compatible Devices
The Catalyst 3560 switch can connect to a Cisco IP Phone through a straight-through, twisted four-pair 
Category 5 cable. The rear panel of the Cisco IP Phone might have more than one RJ-45 connector. Use 
the LAN-to-phone connector to connect the IP phone to the switch. See the Cisco IP Phone 
documentation for more information about...

 
2-21
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Connecting the Switch to Compatible Devices
Step 3Reconfigure and reboot the connected device, if necessary.
Step 4Repeat Steps 1 through 3 to connect each device.
Connecting to Fiber-Optic SFP Modules
WarningClass 1 laser product. Statement 1008
CautionDo not remove the rubber plugs from the SFP module port or the rubber caps from the fiber-optic cable 
until you are ready to...

 
2-22
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Connecting the Switch to Compatible Devices
If the LED is off, the target device might not be turned on, there might be a cable problem, or there 
might be problem with the adapter installed in the target device. See Chapter 4, “Troubleshooting,” 
for solutions to cabling problems.
Step 5If necessary, reconfigure and restart the switch or target device.
Connecting to 1000BASE-T...

 
2-23
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Connecting the Switch to Compatible Devices
If the LED is off, the target device might not be turned on, there might be a cable problem, or there 
might be problem with the adapter installed in the target device. See Chapter 4, “Troubleshooting,” 
for solutions to cabling problems.
Step 4If necessary, reconfigure and restart the switch or target device.
Connecting to a...

 
2-24
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2      Switch Installation (24- and 48-Port Switches)
Where to Go Next
Where to Go Next
If the default configuration is satisfactory, the switch does not need further configuration. You can use 
any of these management options to change the default configuration:
Start the device manager, which is in the switch memory, to manage individual switches. The device 
manager is a web interface that offers quick configuration and...

CH A P T E R
 
3-1
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
3
Switch Installation (8- and 12-Port Switches)
This chapter describes how to start your switch installation, including how to interpret the power-on 
self-test (POST) that ensures proper operation. It also describes how to install the switch.
NoteThis chapter describes the installation information specific to the Catalyst 3560-8PC and 
Catalyst 3560-12PC-S switches. For installing the other Catalyst 3560 switches, see Chapter...

 
3-2
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 3      Switch Installation (8- and 12-Port Switches)
Preparing for Installation
Warnings
These warnings are translated into several languages in the Regulatory Compliance and Safety 
Information for the Catalyst 3560 Switch.
WarningTo prevent the switch from overheating, do not operate it in an area that exceeds the maximum 

3 inches (7.6 cm) of clearance around the ventilation openings. Statement 17B
WarningBefore working on...

 
3-3
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 3      Switch Installation (8- and 12-Port Switches)
Preparing for Installation
WarningDo not work on the system or connect or disconnect cables during periods of lightning activity. 
Statement 1001
WarningBefore performing any of the following procedures, ensure that power is removed from the DC circuit. 
Statement 1003
WarningRead the installation instructions before connecting the system to the power source. Statement 1004...

 
3-4
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 3      Switch Installation (8- and 12-Port Switches)
Preparing for Installation
WarningThis equipment must be grounded. Never defeat the ground conductor or operate the equipment in the 
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection 
authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
WarningThis unit might have more than one power...