Cisco 3560 Poe8 Manual

 
C-1
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
APPENDIXC
Connecting to DC Power
This appendix describes how to make DC power connections to the Catalyst 3560V2-24TS-SD switch. 
See “Switch Installation (24- and 48-Port Switches)” and “Switch Installation (8- and 12-Port 
Switches)” for instructions on installing the switch.
Connecting to DC Power 
To connect the Catalyst 3560V2-24TS-SD switch to a DC-input power source, follow the steps in these 
sections:
Preparing for Installation,...

 
C-2
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Appendix C      Connecting to DC Power
Connecting to DC Power
CautionThe Catalyst 3560V2-24TS-SD switch is suitable only for intrabuilding or nonexposed wiring 
connections.
Preparing for Installation
Locate the ground lug and the two number-10-32 screws on the switch rear panel and the DC terminal 
block plug in the DC-switch accessory kit.
Obtain these necessary tools and equipment:
Ratcheting torque screwdriver with a Phillips head that...

 
C-3
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Appendix C      Connecting to DC Power
Connecting to DC Power
Figure C-1 Stripping the Ground Wire
Step 3Slide the open end of the ground lug over the exposed area of the 6-gauge wire.
Step 4Using a Panduit crimping tool, crimp the ground lug to the 6-gauge wire, as shown in Figure C-2.
Figure C-2 Crimping the Ground Lug
Step 5Use the two number-10-32 screws to attach the ground lug and wire assembly to the switch rear panel 
ground...

 
C-4
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Appendix C      Connecting to DC Power
Connecting to DC Power
Figure C-3 Attaching the Ground Lug Assembly Over the RPS Connector
Figure C-4 Attaching the Ground Lug to the Ground Lug Hole
274667CONSOLE
1Ground hole location
274668
1 

 
C-5
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Appendix C      Connecting to DC Power
Connecting to DC Power
Wiring the DC-Input Power Source
WarningBefore performing any of the following procedures, ensure that power is removed from the DC circuit. 
Statement 1003
WarningOnly trained and qualified personnel should be allowed to install, replace, or service this equipment. 
Statement 1030
CautionYou must connect the Catalyst 3560V2-24TS-SD switch only to a DC-input power source that...

 
C-6
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Appendix C      Connecting to DC Power
Connecting to DC Power
Figure C-6 Stripping the DC-Input Power Source Wire
Step 5Insert the exposed wire of one of the four DC-input power source wires into the terminal block plug, as 
shown in Figure C-7. Make sure that you cannot see any wire lead. Only wire with insulation should 
extend from the terminal block.
WarningAn exposed wire lead from a DC-input power source can conduct harmful levels of...

 
C-7
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Appendix C      Connecting to DC Power
Connecting to DC Power
Figure C-8 Torquing the Terminal-Block Captive Screws
Step 7Repeat Steps 4 and 5 for the remaining three DC-input power source wires. Figure C-9 shows the 
completed wiring of a terminal block plug.
Figure C-9 Completed Wiring of Terminal Block Plug
Step 8Insert the terminal block plug in the terminal block header on the switch rear panel, as shown 
in Figure C-10.
CautionSecure...

 
C-8
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Appendix C      Connecting to DC Power
Connecting to DC Power
Figure C-10 Inserting the Terminal Block in the Block Header
Step 9Remove the tape from the circuit-breaker switch handle, and move the circuit-breaker handle to the 
on position.
1Tie wrap2Terminal block
274669CONSOLE
1
2 

 
D-1
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
APPENDIXD
Configuring the Switch with the CLI-Based Setup 
Program
This appendix provides a command-line interface (CLI)-based setup procedure for a standalone switch. 
Review the safety warnings in Chapter 2, “Switch Installation (24- and 48-Port Switches)” and 
Chapter 3, “Switch Installation (8- and 12-Port Switches).”
See the Catalyst 3560 Switch Getting Started Guide for setting up the switch by using Express Setup.
Preparing for...

 
D-2
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Appendix D      Configuring the Switch with the CLI-Based Setup Program
Preparing for Setup
Step 2Use the supplied RJ-45-to-DB-9 adapter cable to insert the RJ-45 connector into the console port on the 
switch rear panel, as shown in Figure D-2. 
Figure D-2 Connecting a Switch to a PC
Step 3
Attach the DB-9 female DTE of the adapter cable to a PC serial port, or attach an appropriate adapter to 
the terminal.
Step 4Wait before you power on...