Christie Projector Mirage WU-L User Manual

D-16Mirage WU-L User Manual020-100774-01 Rev. 2 4-2012
Appendix D: Serial Command Reference
(CCS) SELECT OUTPUT COLOR 
CONTROL GROUP: Input     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
Selects which of several predefined and 4 user defined color maps to use for a specific Input signal. 
0 = MaxDrives - All color adjustments are turned off allowing the projector to run at maximum brightness. 
1 = Color Temperature - This will allow you to specify a color temperature between 3200...

Appendix D: Serial Command Reference
Mirage WU-L User ManualD-17020-100774-01 Rev. 2 (4/2012)
PIIPSet the channel being used by PIP. 
INFODisplay the information on the current channel. 
EXAMPLES:
(CHA?) - Get current active channel. 
(CHA 10) - Set main to channel 10. 
(CHA+PIIP 99) - Set PIP to channel 99. 
(CHA+COPY 1) - Make a copy of channel 1, using the next free channel number. 
(CHA+COPY 1 20) - Make a copy of channel 1, and copy to channel 20 (will fail if 20 already exists). 
(CHA+DLET 0) -...

D-18Mirage WU-L User Manual020-100774-01 Rev. 2 4-2012
Appendix D: Serial Command Reference
Value Range: 
0 = sync tip 
1 = backporch 
2 = tri-level
SUBCODE
INxy
DESCRIPTION OF USE
Set the black level clamping for Slot x, Input y.
MAIN Set the black level clamping for main video. 
PIIP
Set the black level clamping for PIP video. 
EXAMPLES:
(CLP 0) - Set the black level clamping for main video to sync tip. 
(CLP+MAIN 0) - Set the black level clamping for main video to sync tip. 
(CLP+IN32 0) - Set the...

Appendix D: Serial Command Reference
Mirage WU-L User ManualD-19020-100774-01 Rev. 2 (4/2012)
SUBCODE
C0xx
DESCRIPTION OF USE
Select a new number for channel (xx=channel number from 01 
to 99). 
EXAMPLE:
(CNM+C001 3) - Change the channel number from 1 to 3.
(CON) CONTRAST 
CONTROL GROUP: Input     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
This control sets the image contrast by adjusting the gain applied to the Input signal. It has exactly the same effect 
as adjusting the Input...

D-20Mirage WU-L User Manual020-100774-01 Rev. 2 4-2012
Appendix D: Serial Command Reference
MAIN Set the luma delay on the main video to the specified value in 
the range -3 pixel to 3 pixel
. 
PIIP
Set the luma delay on the PIP video to the specified value in 
the range of -3 pixel to 3 pixel
. 
EXAMPLES:
(CRM 3) - Set luma delay to 3 pixel on Main video. 
(CRM+MAIN 3) - Set luma delay to 3 pixel on Main video. 
(CRM+PIP 3) - Set luma delay to 3 pixel on PIP video. 
(CRM+IN32 -3) - Set luma delay to -3...

Appendix D: Serial Command Reference
Mirage WU-L User ManualD-21020-100774-01 Rev. 2 (4/2012)
(DED) DUAL DVI EDID TYPE SELECTION 
CONTROL GROUP: Option     SUBCLASS: Power Up           ACCESS LEVEL: Operator
DESCRIPTION
Set the preferred EDID Timings on the Dual DVI Input card. Available Models are:
0 = Default
1 = 3D
2 = Custom 
NOTE
: 3D option (1) is not supported for Entero or Matrix StIM/SIM.
SUBCODE
SLxy
DESCRIPTION OF USE
Set the EDID timings on Slot x to the specified type.
EXAMPLES:
(DED+SL31 2)...

D-22Mirage WU-L User Manual020-100774-01 Rev. 2 4-2012
Appendix D: Serial Command Reference
EXAMPLE:
(DTL 50) - Set the detail to mid point for Main video. 
(DTO) DETAIL OVERSHOOT 
CONTROL GROUP: Input     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
Detail overshoot / undershoot control is provided to minimize ringing on the enhanced edges detail and texture 
effects. 
SUBCODE
INxy
DESCRIPTION OF USE
Set the detail overshoot for Slot x, Input y.
MAIN Set the detail overshoot for...

Appendix D: Serial Command Reference
Mirage WU-L User ManualD-23020-100774-01 Rev. 2 (4/2012)
SUBCODE
SLCT
DESCRIPTION OF USE
Enables or disables Black Level Blending mode, or choose a 
saved Christie TWIST™ Black Level Blending preset
. 
CNTV
Changes edge blending black level in the center zone. 
TOPV
Changes edge blending black level in the top zone.
LFTVChanges edge blending black level in the left zone. 
RHTV
Changes edge blending black level in the right zone. 
BTMV
Changes edge blending black level...

D-24Mirage WU-L User Manual020-100774-01 Rev. 2 4-2012
Appendix D: Serial Command Reference
RHTS Changes edge blending curve slope at the midpoint on the right 
edge.
TOPW Changes edge blending width of the top edge.
TOPM Changes edge blending curve midpoint of the top edge.
TOPS Changes edge blending curve slope at the midpoint on the top 
edge.
BTMW Changes edge blending width of the bottom edge.
BTMM Changes edge blending curve midpoint of the bottom edge.
BTMS Changes edge blending curve slope at the...

Appendix D: Serial Command Reference
Mirage WU-L User ManualD-25020-100774-01 Rev. 2 (4/2012)
(ESM) EM STEALTH MODE 
CONTROL GROUP: Preference     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
Stealth mode extinguishes LEDs on the Electronics Module. Typically this is used in simulation environments 
where extraneous light would detract from the scenario (when the scene involves IR). 
SUBCODE
 
DESCRIPTION OF USE
EXAMPLES:
(ESM 1) - Enable EM stealth mode.
(ESM ?) - Report the stealth...