Christie Projector Mirage WU-L User Manual

D-6Mirage WU-L User Manual020-100774-01 Rev. 2 4-2012
Appendix D: Serial Command Reference
EXAMPLES:
(AIL 1) - Perform auto Input level on the main image. 
(AIL+PIIP 1) - Perform auto Input level on the PIP image.
(ALT) ACTIVE LOOP-THROUGH 
CONTROL GROUP: Preference     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
In situations where a Twin HDMI Input card is being used to loop signals out to another projector, this feature ensures that 
video signals continue to be looped out when...

Appendix D: Serial Command Reference
Mirage WU-L User ManualD-7020-100774-01 Rev. 2 (4/2012)
EXAMPLES:
(APW 0) - Projector will remain in Standby Mode until the user presses the power key. 
(APW 1) - Projector will auto power up when A/C power is switched on.
(ARO) ASPECT RATIO OVERLAY 
CONTROL GROUP: Unsaved     SUBCLASS: Power Up           ACCESS LEVEL: Operator
DESCRIPTION
Enables or disables Aspect Ratio layer over Image layer.
SUBCODE
 
DESCRIPTION OF USE
EXAMPLES:
(ARO 1) - Turns ON Aspect Ratio...

D-8Mirage WU-L User Manual020-100774-01 Rev. 2 4-2012
Appendix D: Serial Command Reference
(ASR) AUTO CHANNEL SELECT 
CONTROL GROUP: Channel     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
The Auto Channel Select (ASR) option allows the projector to select the channel memory best suited to the Input 
signal. If the current channel does not allow Auto Channel Select, the projector will not attempt to select a new 
channel when the signal changes. If the current channel does allow...

Appendix D: Serial Command Reference
Mirage WU-L User ManualD-9020-100774-01 Rev. 2 (4/2012)
PIIPPerform a standard Auto Setup on the picture-in-picture (PIP) 
video.
EXAMPLES:
(ASU) - Perform standard Auto Setup on main video. 
(ASU+MAIN) - Perform standard Auto Setup on main video. 
(ASU+PIIP) - Perform standard Auto Setup on PIP. 
(BBL) BOTTOM BLANKING 
CONTROL GROUP: Input     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
Set the number of lines to blank (turn to black) at the...

D-10Mirage WU-L User Manual020-100774-01 Rev. 2 4-2012
Appendix D: Serial Command Reference
SUBCODE
PRTA
DESCRIPTION OF USE
Set the baud rate on port A (RS-232 IN). 
PRTB Set the baud rate on port B (RS-232 OUT). 
PRTC  Set the baud rate on port C (RS-422). 
EXAMPLES:
(BDR+PRTA 6) - Set baud rate on port A to 115200 bits per second. 
(BDR+PRTA?) - Get baud rate (BDR+PRTA!115200). 
(BGC) BASE GAMMA CURVE 
CONTROL GROUP: Input     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
This...

Appendix D: Serial Command Reference
Mirage WU-L User ManualD-11020-100774-01 Rev. 2 (4/2012)
PIIP  Set the base gamma curve for PIP video. 
EXAMPLES:
(BGF 100) - Set the base Gamma Function to 1.0 for main video. 
(BGF+MAIN 300) - Set the base Gamma Function to 3.0 for main video. 
(BGF+IN32 222) - Set the base Gamma Function to 2.22 for Slot 3, Input 2. 
(BGS) BASE GAMMA SLOPE 
CONTROL GROUP: Input     SUBCLASS: Power Up           ACCESS LEVEL: Operator
DESCRIPTION
Defines the slope to be used for the...

D-12Mirage WU-L User Manual020-100774-01 Rev. 2 4-2012
Appendix D: Serial Command Reference
(BLB) BLUE BLACK LEVEL 
CONTROL GROUP: Input     SUBCLASS: Power Down          ACCESS LEVEL: Operator
DESCRIPTION
Blue black level is used to compensate for relative variations in the black levels between Red, Green and Blue. 
This is available on all cards expect the Video decoder. 
The correct setting achieves maximum contrast without crushing white or black. When the drive and black level 
controls are set...

Appendix D: Serial Command Reference
Mirage WU-L User ManualD-13020-100774-01 Rev. 2 (4/2012)
EXAMPLES:
(BLD 128) - Set blue drive to 128 on main video. 
(BLD+MAIN 128) - Set blue drive to 128 on main video.
(BLD+PIIP 100) - Set blue drive to 100 on PIP video. 
(BLD+IN32 100) - Set blue drive to 100 on Slot 3 Input 2. 
(BLD?) - Returns the current blue drive value on main video. 
(BLD+PIIP?) - Returns the current blue drive value on PIP video. 
(BLD+IN12?) - Returns the current blue drive value on Slot 1...

D-14Mirage WU-L User Manual020-100774-01 Rev. 2 4-2012
Appendix D: Serial Command Reference
(BRT) BRIGHTNESS 
CONTROL GROUP: Input     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
The Brightness control adjusts the offset applied to the Input signal. It has exactly the same effect as adjusting the 
Input levels, except that it operates an all 3 colors and can be used to make quick adjustments. For precise control, 
the Input level adjustments should be used. If the setting is too...

Appendix D: Serial Command Reference
Mirage WU-L User ManualD-15020-100774-01 Rev. 2 (4/2012)
UIH2 Get/Set the percent of gain at right turn point.
UI1P Get/Set position of left turn point.
UI2P Get/Set position of right turn point.
GAIN Get/Set overall gain.
UIRT Restore all parameters to factory default.
EXAMPLES:
(BRU+SLCT?) - Get current state of brightness uniformity, 0 is disabled, 1 is enabled.
(BRU+SLCT 1) - Enable brightness uniformity. 
(CCD) OUTPUT COLOR DEFAULT 
CONTROL GROUP: Preference...