Christie Projector J Series 1000W & 1200W User Manual

Section 3: Operation
J Series 1000W and 1200W User Manual3-41020-100706-02  Rev. 1  (03-2014)
4. When adjustment of the corners is complete, select OK. NOTE: A message will be displayed indicating 
that the projector is  “Processing request”.  The settings are applied to the  displayed image, and will take 
approximately 10 seconds. If Vertical Keystone adjust ments have been made, starting to do any Horizontal 
Keystone adjustments will erase the Ve rtical settings, and vice versa.
5. After the...

3-42J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   (03-2014)
Section 3: Operation
WHAT IS BRIGHTNESS UNIFORMITY?
When used to refine screens already matched for their primary colors, see 3.12 Using Multiple Projectors:  
Matching Colors in Multiple Screens  and overall light output, proper adjustment of  Brightness Uniformity 
can create an exceptionally smooth screen in which:
• No area of the screen appears more red, green or blue than another 
• No area of the screen appears brighter than...

Section 3: Operation
J Series 1000W and 1200W User Manual3-43020-100706-02  Rev. 1  (03-2014)
Step 1: Setup
a. Adjust primary colors see  3.12 Using Multiple Projectors : Matching Colors in Multiple Screens  to 
ensure matched overall color temperat ures and light output between screens. 
IMPORTANT!  
Double-check that all WHITES and LIGHT OUTPUT are well-matched.
b. Enable the Brightness Uniformity  check box. This will enable access to the unif ormity controls and 
will apply the settings to your...

3-44J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   (03-2014)
Section 3: Operation
Step 3: Adjust Light Output in Eight Zones
a. For each screen, compare the light output of each e dge and corner to that of the center. If any of the 
areas differ, use the  White Uniformity menu to match edges and corners to the center as described 
below. Begin with the screen  exhibiting the most obvious variations in light output.
•Adjust  edge White Uniformity  first—note that each edge adjustment also...

Section 3: Operation
J Series 1000W and 1200W User Manual3-45020-100706-02  Rev. 1  (03-2014)
For best results, use the same projector model 
and type throughout your display wall. In 
addition, avoid high-gain screens whenever 
possible—the optical performance of such 
screens demands minimal image offset, thus 
projectors must be loca ted very close to one 
another.
Edge blending software controls are located in 
the two-page  Edge Blending submenu—
access via  Configuration  menu, then go to the...

3-46J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   (03-2014)
Section 3: Operation
Edge Blending Procedure
NOTES: 1) Before attempting to work with  edge blending software functions , align the projectors/images by 
correctly overlapping the displays fro m your intended external source. 
2) Match colors and the brightness 
uniformity.
IMPORTANT!  For a shared edge, all blend procedures and settin gs should be identical on both projectors.
1. Start with two projectors. Display fu ll white...

Section 3: Operation
J Series 1000W and 1200W User Manual3-47020-100706-02  Rev. 1  (03-2014)
COLOR ADJUSTMENTS BY X/Y - Submenu
Enter known x/y coordinates from the chromaticity graph
NOTES: 1) For defining or changing a User 1, 2, 3, or 4 
color performance or “gamut”. Sometimes known as 
Comprehensive Color Adjustment™. 
2) Factory-defined 
primary color levels, which ensure a specific color 
performance from projector-to-projector, can be calibrated in 
the Service menu only. The fact ory settings...

3-48J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   (03-2014)
Section 3: Operation
FIGURE 3-38 CIE 1931 CHROMATICITY DIAGRAM 
NOTE:
  Keep new x,y coordinates w ithin the original color gamut triangle shown here.
COLOR SATURATION - Submenu
Adjust color slide bars and judge im age color by eye or meter. A user-defined color “adjustment” can be 
applied by selecting it in the  Advanced Image Settings menu (select ‘Color Adjustment’).
Use this submenu if you do not have  specific color...

Section 3: Operation
J Series 1000W and 1200W User Manual3-49020-100706-02  Rev. 1  (03-2014)
Procedure
NOTES: 1) Adjust white levels before adjusting black levels. 2) The zones in BLB menu correspond to the Edge 
Blend zones. If a given Edge Blend zone width is set to  0 (i.e. no blend on that side) then the corresponding 
BLB zone is disabled. It only becomes accessi ble when that Edge Blend zone is active.
1. Start with two projectors. 
2. Select the black test pattern for both projectors from the...

3-50J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   (03-2014)
Section 3: Operation
The features that act differently when Tiling is enabled are:
The PIP border is disabled
 Cascading menus are turned off
 Menus show only 5 items, with a scroll bar to allow the rest of  the menu items to be reached.
 Projector source switching in the array is not synchr onized. Therefore some latency can be seen from when 
the commands are issued to each  projector, causing switching to not  be as seamless...