Christie Projector J Series 1000W & 1200W User Manual

Section 4: Web User Interface
J Series 1000W and 1200W User Manual4-11020-100706-02  Rev. 1  (03/2014)
• Click the Test button to test the entered command string. NOTE: If the test passed or failed, a green or 
red icon appears to the right side of the  Test button as shown in  Figure 4-16 Test Buttons .
FIGURE 4-16 TEST BUTTONS
10. Click Finish to create the added event. NOTES 1) The added event appears in the  RTE Listing  window. 
See  Figure 4-17 RTE Listing Window Example . 
2) To activate or...

4-12J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   03-2014
Section 4: Web User Interface
To  A d d  a  G P I O  E v e n t
1. Click Add to open the  RTE Wizard .
2. Select the GPIO Event tab.
3. For the GPIO Event  option define the Input 
Condition  field as required. The  Input 
Condition  field contains 7 blocks which refer to 
the 7 I/O pins on the GPIO connector. Pin 1 = 
+12V and Pin 5 = Ground are not included or 
changed. 
2) Clicking a block toggles between H, 
L, and X as shown in...

Section 4: Web User Interface
J Series 1000W and 1200W User Manual4-13020-100706-02  Rev. 1  (03/2014)
TO ADD A SERIAL COMMAND
1. Enter a serial command in the Serial Command 
field. 
NOTE:  For Serial Commands refer to the M 
Series Serial Commands Technical Reference 
Information P/N 020-100224-xx, available at the 
Christie Website.
2. Click Send to add the serial command. See  Figure 
4-22 .   
4.3.8 About Tabbed Page
Provides information about  the projector software 
version, model, serial numb er,...

J Series 1000W and 1200W User Manual5-1020-100706-02  Rev. 1  (03-2014)
 
5 Maintenance
Installers, service trained operators and all other users must maintain a safe operating environment at all
times. Read through this section in  its entirety and understand all warnings and precautions before
attempting to operate this proj ector. Refer to Section 1.2 Safety Warnings and Guidelines.
5.1 Projector Location
Operate the projector in an environment that meet s the operating range specifications in Section...

5-2J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   (03-2014)
Section 5: Maintenance
1. TURN THE LAMP OFF
Press the power to switch the lamp off. Allow the cooling fans to stop automatically (within 5 minutes) before 
proceeding with step 2. 
NOTE:  This wait period is required to allow  the lamp to sufficiently cool before 
handling.
2. UNPLUG THE PROJECTOR
When the cooling fans have stopped, turn the main  switch of the projector off, then unplug the projector.
 Always power down and unplug...

Section 5: Maintenance
J Series 1000W and 1200W User Manual5-3020-100706-02  Rev. 1  (03-2014)
4. RELEASE THE LAMP LOCK
Pull out and turn the lamp lock lever, which is located to the left of the lamp module, turn it 1/4 turn counter 
clockwise to the “unlock” position. See  Figure 5-2. 
FIGURE 5-2 
5. REMOVE THE LAMP MODULE
Firmly grasp the lamp by its housing only and pull it straight out (lamp slides along guides) until it is free. See 
Figure 5-3 . Discard the lamp using safe  disposal/recycling...

5-4J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   (03-2014)
Section 5: Maintenance
8. LOCK IN THE NEW LAMP MODULE
Pull out and turn the lamp lock lever 1/4 turn clockwise to “lock” the lamp in place. 
NOTE: If you are unable to 
turn the lamp lock into position, repe at step 6 to ensure the lamp is making full contact with the terminal block.
9. REPLACE THE LAMP DOOR
Replace the lamp door and secure it with the two (2) screws removed in step 2.
IMPORTANT:  The lamp module is calibrated for...

Section 5: Maintenance
J Series 1000W and 1200W User Manual5-5020-100706-02  Rev. 1  (03-2014)
5.2 Replacing the Projection Lens
IMPORTANT! Remove the rear lens cap from the new lens. Keep the front lens cap on the lens to protect it 
during installation.
1. Rotate the lens clamp to the OPEN  position, to remove old lens. See Figure 5-6.
FIGURE 5-6 
2. Align the new lens interface plate  with the lens mount. Align the lens electrical connector with the mating 
connector on the lens mount. Fully insert...

5-6J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   (03-2014)
Section 5: Maintenance
FIGURE 5-7 
3. While holding the lens flat against the lens mount, rotate the lens clamp clockwise to lock the lens 
assembly in place. See  Figure 5-8 .
FIGURE 5-8 
4. Remove the front lens cap.
5. For added stability such as motion ap plications, fasten the security screws provided with the lens mount. 
See  Figure 5-9 .
FIGURE 5-9 
6. Use a 5mm hex driver to fasten the red s ecurity screws provided with the...