Christie Projector J Series 1000W & 1200W User Manual

							Section 4: Web User Interface
J Series 1000W and 1200W User Manual4-11020-100706-02  Rev. 1  (03/2014)
• Click the Test button to test the entered command string. NOTE: If the test passed or failed, a green or 
red icon appears to the right side of the  Test button as shown in  Figure 4-16 Test Buttons .
FIGURE 4-16 TEST BUTTONS
10. Click Finish to create the added event. NOTES 1) The added event appears in the  RTE Listing  window. 
See  Figure 4-17 RTE Listing Window Example . 
2) To activate or deactivate one or more RTEs listed in the 
RTE Listing  window, select or clea r each check box in the  Active column accordingly.
FIGURE 4-17 RTE LISTING WINDOW EXAMPLE
TO ADD A SYSTEM EVENT
1. Click  Add to open the  RTE Wizard .
2. Select the System Event tab.
3. Select a type of event from the  System Event drop-down list. 
NOTE: Depending on the selection made, 
additional selections are made ava ilable in the second drop-down list located underneath (i.e. Input 
Change > Input 1, Slot 1).  See Figure 4-18 Add System Event .
FIGURE 4-18 ADD SYSTEM EVENT 
						

							4-12J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   03-2014
Section 4: Web User Interface
To  A d d  a  G P I O  E v e n t
1. Click Add to open the  RTE Wizard .
2. Select the GPIO Event tab.
3. For the GPIO Event  option define the Input 
Condition  field as required. The  Input 
Condition  field contains 7 blocks which refer to 
the 7 I/O pins on the GPIO connector. Pin 1 = 
+12V and Pin 5 = Ground are not included or 
changed. 
2) Clicking a block toggles between H, 
L, and X as shown in  Figure 4-19 GPIO Event . 
See  Appendix B:  for detailed information.
To Add a Function Key Event
1. Click  Add to open the  RTE Wizard .
2. Select the Function Key Event tab.
3. Select a  Function key from the drop-down list as 
shown in  Figure 4-20 Function Key Event . Refer 
to   Section 3: Operation  for detailed information.
To Add a DMX Channel Event
1. Click  Add to open the  RTE Wizard .
2. Select the DMX Channel Event tab.
3. Select a  DMX channel (DMX-56 to DMX-61) 
from the drop-down list as shown in Figure. 
Refer to   Section 3: Operation  for detailed 
information.
FIGURE 4-19 GPIO EVENT
FIGURE 4-20 FUNCTION KEY EVENT
FIGURE 4-21  DMX CHANNEL EVENT 
						

							Section 4: Web User Interface
J Series 1000W and 1200W User Manual4-13020-100706-02  Rev. 1  (03/2014)
TO ADD A SERIAL COMMAND
1. Enter a serial command in the Serial Command 
field. 
NOTE:  For Serial Commands refer to the M 
Series Serial Commands Technical Reference 
Information P/N 020-100224-xx, available at the 
Christie Website.
2. Click Send to add the serial command. See  Figure 
4-22 .   
4.3.8 About Tabbed Page
Provides information about  the projector software 
version, model, serial numb er, and license information. 
NOTE: The information pr ovided on the Version and 
License  tabs are read-only.
FIGURE 4-22  ADD SERIAL COMMAND 
						

							J Series 1000W and 1200W User Manual5-1020-100706-02  Rev. 1  (03-2014)
 
5 Maintenance
Installers, service trained operators and all other users must maintain a safe operating environment at all
times. Read through this section in  its entirety and understand all warnings and precautions before
attempting to operate this proj ector. Refer to Section 1.2 Safety Warnings and Guidelines.
5.1 Projector Location
Operate the projector in an environment that meet s the operating range specifications in Section 7 Specifica-
tions . Do not operate the projector close to  water, such as near a swimming pool.
Do not place the projector on an unst able cart, stand or table. If the projector is going to be ceiling mounted, 
only use the Christie appr oved ceiling mount fixture designed for your projector.
A projector and cart combination should be used with  care. Sudden stops, excessive force, and uneven surfaces 
may cause the projector and ca rt combination to overturn.
5.1.1 Lamp and Filter Replacement
Lamp
Do not operate the lamp for more than the warranty limit; risk of the lamp  shattering increases as a result of 
changes in the quartz glass that o ccur with use. Operation beyond the la mp warranty limit also significantly 
reduces brightness output.
  Wait approximately 5 minutes after powering  down the projector to allow the lamp to 
cool sufficiently before removing. 
  Never attempt to remove the lamp housing  directly after use. The lamp is under great 
pressure when hot and may explode, causing  personal injury and/or property damage. 
  Use only lamps supplied by Christie.
Lamp Replacement Procedure 
  Choose the correct wattage lamp supplied  by Christie. See Table 5.1. Read the lamp 
replacement procedure in its  entirety before proceeding.
  A Christie accredited service technician must perform lamp replacement. 
  Cool the lamp completely and handle by the housing only.
  Do not touch the glass window of the lamp. Fingerprints left on the surface can lead to  an intense accumulation of heat called a “hotspot,” which could potentially result in 
lamp failure. It is recommended you wear a face shield when working with the lamp.
For this procedure you will need the appropriate Lamp  and Filter Kit manufactured by Christie Digital 
Systems. See  Ta b l e  5 . 1.
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING 
						

							5-2J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   (03-2014)
Section 5: Maintenance
1. TURN THE LAMP OFF
Press the power to switch the lamp off. Allow the cooling fans to stop automatically (within 5 minutes) before 
proceeding with step 2. 
NOTE:  This wait period is required to allow  the lamp to sufficiently cool before 
handling.
2. UNPLUG THE PROJECTOR
When the cooling fans have stopped, turn the main  switch of the projector off, then unplug the projector.
 Always power down and unplug the projecto r prior to servicing. Allow the lamps to 
cool before handling.
3. REMOVE THE LAMP DOOR
 Protective gear required. Wear a face shield.
Using a #2 Phillips screwdriver,  loosen the two (2) lock screws securing the lamp door, which is located at the 
rear of the projector below the Input panel. See  Figure 5-1.
FIGURE 5-1 
Table 5.1 
Projector Part Number Projector Mode l Lamp Type Lamp/Filter Kit Required
DS+8K-J 132-004105-XX 1.0 kW 003-120116-XX
Mirage DS+8K-J 132-004127-XX
HD7K-J 132-005106-XX
Mirage HD7K-J 132-005128-XX
Mirage WU7K-J 132-006129-XX
Matrix WU7K-J 132-006130-XX
DS+10K-J 132-007108-XX 1.2 kW 003-120117-XX 
HD9K-J 132-008109-XX
WARNING
WARNING 
						

							Section 5: Maintenance
J Series 1000W and 1200W User Manual5-3020-100706-02  Rev. 1  (03-2014)
4. RELEASE THE LAMP LOCK
Pull out and turn the lamp lock lever, which is located to the left of the lamp module, turn it 1/4 turn counter 
clockwise to the “unlock” position. See  Figure 5-2. 
FIGURE 5-2 
5. REMOVE THE LAMP MODULE
Firmly grasp the lamp by its housing only and pull it straight out (lamp slides along guides) until it is free. See 
Figure 5-3 . Discard the lamp using safe  disposal/recycling practices.
FIGURE 5-3 
6. RECORD THE SERIAL NUMBER OF THE NEW LAMP
7. INSERT THE NEW LAMP MODULE
Align the new lamp with the top and bottom guides on  the left side of the lamp compartment. See Figure 5-4. 
Slide the lamp into the terminal block. 
NOTE:  A slightly harder push may be required to ensure it is fully 
seated. 
FIGURE 5-4  
						

							5-4J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   (03-2014)
Section 5: Maintenance
8. LOCK IN THE NEW LAMP MODULE
Pull out and turn the lamp lock lever 1/4 turn clockwise to “lock” the lamp in place. 
NOTE: If you are unable to 
turn the lamp lock into position, repe at step 6 to ensure the lamp is making full contact with the terminal block.
9. REPLACE THE LAMP DOOR
Replace the lamp door and secure it with the two (2) screws removed in step 2.
IMPORTANT:  The lamp module is calibrated for maximum perfo rmance and brightness. Do not attempt to re-
align or adjust the lamp module.
10. In the lamp menu, select  CHANGE LAMP. This will prompt for the old lamp serial number (if it was not 
previously entered). Enter the new lamp serial number. 
NOTE:  This action is not mandatory, it is 
recommended for accurate lamp statistics to be archived.
Filter Replacement Procedure 
 Only use Christie approved filters. See Table 5.1.
The filter located at the front  side of the projector and should be repl aced whenever the lamp is replaced. If you 
are working in an extremely dusty environment you may want to replace the filter sooner. If this filter is not 
replaced, airflow may become restricted and cause the  projector to overheat.Use the filter provided in the 
Christie approved Lamp and Filter Kit for yo ur specific projector model. See Table 5.1.
1. TURN OFF THE PROJECTOR, COOL AND UNPLUG
Before removing or installing a filter, turn off the  projector and allow it to cool for 5 minutes before 
unplugging.
2. REMOVE FILTER DOOR
Loosen the 2 lock screws at the top of the filter  door. Lift the door away from the projector. See  Figure 5-5.
FIGURE 5-5 
3. REPLACE FILTER
Remove the old filter and insert the new one. 
NOTE: The direction arrows on the outside edge of the filter. 
Ensure the filter is installed with th e arrows pointing into the projector.
4. RE-INSTALL THE FILTER DOOR
Secure the lock screws.
WARNING 
						

							Section 5: Maintenance
J Series 1000W and 1200W User Manual5-5020-100706-02  Rev. 1  (03-2014)
5.2 Replacing the Projection Lens
IMPORTANT! Remove the rear lens cap from the new lens. Keep the front lens cap on the lens to protect it 
during installation.
1. Rotate the lens clamp to the OPEN  position, to remove old lens. See Figure 5-6.
FIGURE 5-6 
2. Align the new lens interface plate  with the lens mount. Align the lens electrical connector with the mating 
connector on the lens mount. Fully insert the assemb ly straight into the lens mount opening without 
turning. Press using your hand as shown in  Figure 5-7. 
NOTE: Ensure the lens is not inserted at an angle, 
as this can cause damage.
LARGE LENS CAP 
						

							5-6J Series 1000W and 1200W User Manual020-100706-02  Rev. 1   (03-2014)
Section 5: Maintenance
FIGURE 5-7 
3. While holding the lens flat against the lens mount, rotate the lens clamp clockwise to lock the lens 
assembly in place. See  Figure 5-8 .
FIGURE 5-8 
4. Remove the front lens cap.
5. For added stability such as motion ap plications, fasten the security screws provided with the lens mount. 
See  Figure 5-9 .
FIGURE 5-9 
6. Use a 5mm hex driver to fasten the red s ecurity screws provided with the lens mount (Figure 5-9). 
NOTES:  1)  Recommended for heaviest lenses such as 0.73:1 and 1.2:1 . 2) The red security screws 
MUST be installed when hoisting the projector ov erhead, or installing the projector in an overhead 
position.
 Use of the lens red security screws or the lens retaining screws is required if the 
projector is hoisted or installed in an overhead position.WARNING