Christie Projector J Series 1000W & 1200W User Manual
Have a look at the manual Christie Projector J Series 1000W & 1200W User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 476 Christie manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
J Series 1000W and 1200W User Manual7-1020-100706-02 Rev. 1 (03-2014) 7 Specifications This section provides detailed J Series features; including inputs, lamp, and power requirements. NOTE: Due to continuing research, detailed feat ures are subject to change without notice. 7.1 Image Performance 7.1.1 Pixel Format 7.1.2 Nominal Brightness 7.1.3 Contrast 7.1.4 Luminance Uniformity 1080p (H x V square pixels) 1920 x 1080 SXGA+ (H x V square pixels) 1400 x 1050 WUXGA (H xV square pixels) 1920 x 1200 Projector Base Model Lamp Power Brightness (ANSI)Center 1200W 1080p 1200W 8000 8800 1000W 1080p 1000W 6200 6850 1200W SXGA+ 1200W 8500 9350 1000W SXGA+ 1000W 6800 7500 1200W WUXGA 1200W 8000 8800 1000W WUXGA 1000W 6200 6850 ANSI: 16 pt. checker pattern on black screen 650:1 typical Full field: 9 pt. averag e ON/OFF with background light subtraction 1800:1 typical (full open aperture) 1080p 90% brightness uniformity SXGA+ 80% brightness uniformity 1080p, WUXGA
7-2J Series 1000W and 1200W User Manual020-100706-02 Rev. 1 (03-2014) Section 7: Specifications 7.1.5 Color Primaries 7.1.6 Gamma 7.1.7 Grayscale/Color Resolution 7.1.8 Color Temperature 7.1.9 Convergence Convergence zones A, B, C are as defined in Figure 2. Zone A has a diameter ¼ of the image height. Zone B has a diameter of full image height. All specified conve rgence errors are between any two colors after a minimum warm-up of 30 minutes. Convergence is specified with a 1.4-1.8 HD lens (part number 118-100112-01) in the 1.4:1 position with zero offset. Bore- sight alignment must be adjust ed for zero angular error. (Note: convergence error includes the effects of lateral color in the projection lens. Measurements must be done on horizontal and vertical test pattern lines that intersect the center of the image). ANSI 9 point measurement without YNF x y Red 0.665 ± .025 0.335 ± .025 Green 0.343 ± .040 0.640 ± .040 Blue 0.145 ± .020 0.050 ± .025 White 0.300 ± .050 0.300 ± .050 Default Gamma (all points from 10 to 90 IRE) 2.2 + linear segment Adjustable Gamma range 1.0 to 3.0 Resolution 10 bits (non-linear) min. (Gamma encoded) White Default CCT 7250K ±950K Range of Adjustment 3200 K - 9300 K Tracking (deviation from normal over full range from 10 – 100 IRE) ±500 K max Stability (during rated lamp life) ±500 K max
Section 7: Specifications J Series 1000W and 1200W User Manual7-3020-100706-02 Rev. 1 (03-2014) 7.1.10 Blemishes 7.1.11 Pixel Defects 7.2 Feature Set 7.2.1 Airflow 7.2.2 Air Filters (Optional) 7.2.3 Dust Sealing 7.2.4 ILS (Intelligent Lens System) Red screenNo blemishes Green screen No blemishes Blue screen No blemishes White screen No blemishes Black screen No blemishes Red 0 bright, up to 1 dark Green 0 bright, 0 dark Blue 0 bright, up to 2 dark non-adjacent Air intakes Front of projector Air exhaust Hot lamp exhaust: rear of projector Cool light engine exhaust: left side and rear of projector Filter media type Dust filter Fog filter Filter access Service-interchangeable via access panel Dust sealed DMDs Gasket sealed Motorized lenses and lens mount with position encoding Zoom, focus, horizontal and vertical offsets Accuracy ±2 pixel Manual control 1/3 pixel fine movement control per button press on any applicable User Interface (e.g., remote). Calibration User Configurable Calibration Modes Automatic calibration on lens change detection Automatic calibration on power-up Manual calibration Calibration time < 10 secs when required Bore sight 3-point +- 4 degrees adjustment and lockable without removing covers Travel time stop to stop Zoom and Focus 10 sec nominal (depends on lens type) Offsets 5 sec (nominal (depends on lens type) Manual Lens Movement Manual over-ride permissible for zoom and focus
7-4J Series 1000W and 1200W User Manual020-100706-02 Rev. 1 (03-2014) Section 7: Specifications 7.2.5 Projection Lens Compatibility Lens Throw Ratio 7.2.6 Automatic Fans 7.2.7 Constant Lamp Output Management Lens type Reverse Telecentric Internal-focus Motorized zoom and focu s with position feedback NOTE: Calculated Throw distance values ar e subject to a ±5% lens tolerance Throw Ratio Lens DescriptionPart NumberSXGA+HDWUXGA FixedLens ILS 0.73:1SX+/0.67:1HD118-100110-xx 0.73 0.67 0.67 Lens ILS 1.2SX+/1.1HD 118-100117-xx 1.2 1.1 1.1 Zoom Lens ILS 1.25-1.6SX+/1.16-1.49HD 118-100111-xx 1.25-1.6 1.16-1.49 1.16-1.49 Lens ILS 1.5-2.0SX+/1.4-1.8HD118-100112-xx 1.5-2.0 1.4-1.8 1.4-1.8 Lens ILS 2.0-2.8SX+/1.8-2.6HD118-100113-xx 2.0-2.8 1.8-2.6 1.8-2.6 Lens ILS 2.8-4.5SX+/2.6-4.1HD118-100114-xx 2.8-4.5 2.6-4.1 2.6-4.1 Lens ILS 4.5-7.5SX+/4.1-6.9HD 118-100115-xx 4.5-7.5 4.1-6.9 4.1-6.9 Lens ILS 7.5-11.2SX+/6.9-10.4HD118-100116-xx 7.5-11.2 6.9-10.4 6.9-10.4 Temperature sensitive fan speed control Fans auto matically adjust maintain proper operating range as function of outs ide ambient temperature Standby All fans are off when projector is in standby and not running active loop-through on a Twin HDMI option card Temperature range 5 to 40 degrees C Transition steps Smooth speed transitions with no abrupt audible changes (Factory Optional) Yellow notch filter Fixed filter to enhance color space LiteLOC ™ Automatically adjusts lamp output to maintain constant lumens setting within operating range of the lamp.
Section 7: Specifications J Series 1000W and 1200W User Manual7-5020-100706-02 Rev. 1 (03-2014) 7.2.8 Shutter 7.2.9 Lamps 7.2.10 Status LED 7.2.11 Electronics/SW OpenLight transmitted to projection lens Closed All light blocked - no light on screen Cermax ® Xenon lamp system Lamps are accessed from the rear of the projector Status LEDs # LED STATES Shutter 1 Green – Shutter is open Yellow – Shutter is closed Status 2Off – AC power is off Yellow – AC is present but projector is in standby Green – Projector is powered up and operating normally Flashing red – Error has occurred. Details are displayed on the status display Comm 3 Flashing green – Projector communication in progress Lamp 4Off – Lamp off Yellow – Lamp time has expired and lamp should be replced Green – Lamp is on and operating correctly Flashing red – Lamp has malfunctioned Flashing yellow – Lamp door is open FEATURE COMMENTS Image Device Supports 3 chip DMD operation Video Format Re-Sizing All video formats can be resized to fill screen either horizontally or vertically while maintaining aspect ratio Picture in Picture Supported Built-in 2D keystone and geometry correction Supported Auto-scaling Supported Auto-de interlacing Supported Edge blending Supported Warping Supported Tiling (max array size) 3x3 Standard Imag e Processor & 2x2 Dual Image Processor Blanking and Image positioning Supported Brightness, contrast, color, and uniformity Settable control Image orientation Can disp lay image front/rear screen, normal/inverted (ceiling) Electronics HW access Mounted at the back of the projector Number of option cards 6 user in ter-changeable – hot swappable Number of processor cards 2 user inter-changeable Number of option slots 4, option cards; 1, processor card Arbitrary Gamma User definable gamma curves
7-6J Series 1000W and 1200W User Manual020-100706-02 Rev. 1 (03-2014) Section 7: Specifications 7.3 Image Processor Performance 7.4 Input (Source Signal) Compatibility 7.4.1 Analog (Only) Input 7.4.2 Twin HDMI Input Min input pixel rate13 Mpix/s Max input pixel rate 165 Mpix/s Standard Mode 330 Mpix/s High Bandwidth mode Standard Image Processor Dual Image Processor Max input resolution 2048x1536 (QXGA) Min input resolution 640x400 Max input frame rate with Dual Image Processor Card 120Hz at 2048x1080 92Hz at 2048x1536* Dual Image Processo r (DIPC) required * QXGA with sources that can output minimum blanking Max imput frame rate with Standard Image Processor Card 50Hz at 2048x1536 (QXGA) *With cources that can output minimum blanking, otherwise lower vertical rates Processing 10 bit throughout * * Except Dual-DVI input in dual-link mode (dual 8 bit input paths into 10 bit processing) Source switching time Switch time 1 second Switch time 3 seconds Low bandwidth signals 3D signals Connectors 5 female BNC, 75 Ohm R/Pr G/Y B/Pb H/C V Color spaces/signal types RGB YPbPr A/D conversion 10 bits Connectors 2 independent HDMI inputs type A 2 loop-out HDMI connectors type A Color spaces/signal types RGB YCbCr (4:2:2) YCbCr (4:4:4) HDCP support HDMI 1.3 supported (not including audio) except: 12 bit color dithered to 10 bits; 16 bit color not supported HDMI 1.4a (Mirage Models)
Section 7: Specifications J Series 1000W and 1200W User Manual7-7020-100706-02 Rev. 1 (03-2014) 7.4.3 Dual Link DVI Input 7.4.4 Video Decoder Input 7.4.5 Dual 3G/HD/SD -SDI Input 7.4.6 DisplayPort InputI 7.5 Control Signal Compatibility 7.5.1 Projector Control Connectors1 dual link DVI-I 1 analog 15-pin VGA Color spaces/signal types HDCP support A/D conversion 10 bits for single link DVI input 8 bits for dual link DVI inputs Frequency 165 MPixel/s analog 330 Mpix/s Dual link DVI (requires DIPC) Connectors 2 S-Video 4-pin miniature DIN 4 BNC, 75 Ohm 2 independent decoder channels for PIP Color space/Signal types Composite video Component video (SD and ED only) S-video Video Standards NTSC, NTSC 4.43, PAL, PAL M, PAL N, PAL 60, SECAM A/D conversion 10 bits Connectors BNC, 75 Ohm Color spaces/signal types Dual HD input SDI, HDSDI 3GHz Connectors 2 independent DisplayPort inputs 2 loop-out DisplayPort connectors Color spaces/signal types RBG YCbCr (4:2:2) YCbCr (4:4:4) HDCP Support on inputs DisplayPort 1.1a supported (not including audio) Number of transmitters 2 IR Modulation frequency Dual frequency (38 kHz) Range Min 35 m Wired Keypad 3 pin XLR connection Max cable length 30 m (not supplied)
7-8J Series 1000W and 1200W User Manual020-100706-02 Rev. 1 (03-2014) Section 7: Specifications 7.5.2 Control Receiver Number of sensors1 front, 1 rear Coverage 130 degrees coverage in-line with lens at 3 m distance Modulation (carrier) frequency Dual frequency (38 kHz)
Section 7: Specifications J Series 1000W and 1200W User Manual7-9020-100706-02 Rev. 1 (03-2014) 7.5.3 RS-232 7.5.4 RS-422 7.5.5 Ethernet 7.5.6 USB 2.0 Device Port 7.5.7 GPIO 7.5.8 DMX512 Interface 7.5.9 Built-In Keypad and Display Number of ports2 Connector 1 female 9-pin Dsub (IN) 1 male 9-pin Dsub (OUT) Max bit rate 115.2 kbps Flow control Xon/Xoff Number of ports 1 Connector 1 female 9-pin Dsub Max bit rate 115.2 kbps Power output 12 V ±5% @ 400mA maximum Number of ports 1 Standard 10/100 Base-T Connector Female RJ-45 Number of ports 1 Standard Not supported (non-functional) Number of I/O Lines 7 Connector Male 9-pin Dsub Output sink current (logic low) 100 mA @ 1V typical Power output 12 V ±5% @ 400mA maximum Connectors Two 5-pin XLR one male (input) and one female (output) DMX Chain Termination Configurable via software Key type Soft-touch keys Display type Graphics LCD backlight
7-10J Series 1000W and 1200W User Manual020-100706-02 Rev. 1 (03-2014) Section 7: Specifications 7.6 Power Requirements 7.6.1 Lamp Specification 7.7 Physical Specifications 7.7.1 Size 7.7.2 Adjustment Parameter Lamp Power Requirement Rated Voltage 1000W 100 VAC - 240 VAC 1200W 200 VAC - 240 VAC Rated Current 1000W 12 A 1200W 10 A Line Frequency All50/60 Hz AC Input Coupler All15 A, 250 VAC, IEC 320-C14 Line Cord 1000W 14AWG type SJT with plug, NEMA 5-15P, 15A 1200W 16AWG type SJT with plug, NEMA 6-15P, 13A Inrush Current All60 A max Maximum Power Consumption 1000W 1200W 1200W 2000W Type Cermax® Xenon Power 1000W 700W min., 1000 W max (software adjustable) 1200W 800W min, 1200W max (software adjustable) Rated lamp life to 50% brightness (2 hrs on, 15 min. off duty cycle) 1000W 1,500 hours min. 1200W 1,000 hours min. Warm-up time (to full output) 10 minutes max Operating position Full rotation allowed about the lamp axis, ±15 deg max. tilt of lamp axis from horizontal Maximum product dimensions (L x W x H) (with lens removed) 561mm (22.1”) x 660mm (26.0”) x 328mm (12.9”) Maximum shipping dimensions (L x W x H) 851mm (33.5”) x 762mm (30”) x 660mm (26”) Product Alignment 50mm (2”) of vertical adjustment on 2 front feet. Rear pad is fixed.