Christie Projector CP2230 User Manual

Installation and Setup
CP2230 User Manual2-15020-100430-07 Rev. 1 (05-2014)
connectors are controlled with the power connector breaker. For more information, see the Interconnect 
Drawing provided with your cinema projector .
6. Turn the LPS Breaker ON.
7. If you are using the extraction unit and cinema  projector power connectors, turn them on.
8. Connect the AC from the site to the socket loca ted on the front bezel of the cinema projector.
2.14 Connect the Cinema Projector to an Optional Uninterrupted...

2-16CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Installation and Setup
2.15 Connect Sources and Turn the Cinema Projector On
After you install the lamp, you can connect external cinema servers and sources. Before you ignite the lamp for 
the first time, use this procedure to ensure  successful communication with input devices.
1. Assign the cinema projector a unique IP address and enter a baud rate: •Tap  Menu > Administrator Setup  > Communications Configuration .
• Enter the IP address for the...

CP2230 User Manual3-1020-100430-07 Rev. 1 (05-2014)
3 Connect Devices to the cinema projector
This section provides information and procedures for connecting input devices to the cinema projector. You 
connect input devices to the cinema projector Intelligence Board (PIB) located on side of the cinema projector.
These communication ports are accessible by removi ng the side source and communication access panel. 
When connecting devices, route all cables along the ch annels located on the bottom of the...

3-2CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Connect Devices to the cinema projector
3.1 Connect a Communications Device
To communicate with the cinema projector, connect the equipment to the Ethernet hub or switch.
For applications or equipment utilizing  serial communications, use the Christie-proprietary serial protocol to 
connect to the RS232 PIB port on the PIB. When using Christie serial protocol over Ethernet connect to port 
5000.
 NOTICE:  The RS232 PIB port located on  the PIB faceplate...

Connect Devices to the cinema projector
CP2230 User Manual3-3020-100430-07 Rev. 1 (05-2014)
3.2 Connect Devices to the SCCI Port
The Simple Contact Closure Port (SCCI) port is a DB-9 (male) connector is located on the PIB input panel and 
is used to control a limited set of  cinema projector functionality through  contact closures. This table lists the 
control functions availa ble through the SCCI:
Table 3.1  SCCI Connector Pinouts 
NOTE: All SCCI inputs require a pulse input of 50ms to  several seconds...

3-4CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Connect Devices to the cinema projector
3.3 Connect Devices to the GPIO Port
The GPIO port is a 37-pin D-sub connector (female) located on the PIB input panel and provides 8 input and 7 
output signals for connecting external devices to the cinema projector. To configure the pins on the connector, 
tap Menu  > Administrator Setup  > GPIO Setup.
As shown below, each available pairing of  pins (+/–) is defined as either an input or output. Four inputs and...

Connect Devices to the cinema projector
CP2230 User Manual3-5020-100430-07 Rev. 1 (05-2014)
If you are wiring your own GPIO cable for use with a server or 3D device such as an IR emitter or a polarizer, 
follow the circuit diagram.
GPO  GPO 
To  C e n t e rPin of BNC
To Shielding
of BNC
+5 VDC (External Supply)
1K 2K
IR Emitter
Recommended Operating Point 
Max. Current
Forward Voltage Drop = 5 mA
= 50 mA
~ 1.1 V (@ 5 mA)
 Figure 3-4 GPIO Circuit Diagram 

3-6CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Connect Devices to the cinema projector
3.4 Connect Devices to the 3D Connector
The 3D connector is a 15-pin D-sub connector (female) located on the PIB  input panel. This table lists the 
control functions available  through the 3D connector.
PINSIGNAL NAMEDIRECTIONDESCRIPTION
1 +12V OutPower to 3D device. Max imum 1A (total between both +12V 
pins).
2 GND /Ground
3 GND /Ground
4 RS232_RX InData to cinema projector  from 3D device. 1200 Baud, 8 bits,...

CP2230 User Manual4-1020-100430-07 Rev. 1 (05-2014)
4 Adjust the Image
This section provides information and procedures for adjusting the cinema projector image.
4.1 Maximize Light Output 
To ensure optimal operation and peak screen bright ness, use LampLOC™ to adjust the lamp position 
whenever you install a new lamp. Wh en you complete the LampLOC adjustment, the lamp is centered and is 
the correct distance from the illumination syst em. Before running LampLOC, verify that:
• The anode yoke is in the...

4-2CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Adjust the Image
4.4 Adjust Offset
Project an image with the primary lens. Always 
adjust offset before boresight. 
Select a framing test pattern and then adjust the 
horizontal and vertical offset to display a square 
image on the screen with minimal cinema 
projector aiming error. ( Figure 4-1) 
NOTES:  1)  For the best optical performance 
and minimize keystone error, use offset and not 
aiming to center the image in off axis 
installations.  2)...