Christie Projector CP2230 User Manual

Installation and Setup
CP2230 User Manual2-5020-100430-07 Rev. 1 (05-2014)
 Keep the cinema projector level when you lift or transport it. Avoid tilting the
cinema projector to the right. This can introduce an air bubble into the coolant hoses that can
result in an air lock and the overheating of the cinema projector.
 Perform a automatic LampLOC™ adjustment  when you move, level, or install a 
new lamp in the cinema projector.
2.5 Position the Cinema Projector
1. If you are installing the cinema...

2-6CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Installation and Setup
 c. Insert the LPS support into the rack stand and align the pins with the holes. 
 d. Lift the LPS into the frame. 
 e. Remove the bottom 10 panels from the back of the rack stand.
 f. Assemble the three piece airflow duct supplied  with the LPS. First, snap the 2 “L” shaped parts 
together, and then snap this  into the 6 stand out pins of the third piece (flat panel).
 g. Position the airflow duct directly behind the LPS....

Installation and Setup
CP2230 User Manual2-7020-100430-07 Rev. 1 (05-2014)
2.6 Adjust Tilt and Level the Cinema Projector
 The cinema projector rear safety strap must be in place before you adjust the 
cinema projector feet.
 DO NOT over-extend the feet. Make sure several threads are engaged into 
the cinema projector’s baseplate.
The lens should be centered and para llel with the screen. This orientation ensures optimum lens performance 
with minimal offset. If this position  is not possible (such as...

2-8CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Installation and Setup
2.7 Install the Touch Panel Controller
1. Loosen the mounting arm so that the end fits over the ball joint located on the rear panel of the cinema 
projector.
2. Tighten the mounting arm until  it fits tightly on the joint.
3. Connect the cable from the TPC to the connecto r on the rear panel of the cinema projector.
4. Adjust the angle of the TPC.
2.8 Connect External Exhaust Ducting
19 mm wrench
Remove rear feet
Prop up rear of...

Installation and Setup
CP2230 User Manual2-9020-100430-07 Rev. 1 (05-2014)
Connect the existing outside-venting ductwork to the 8 inch 
diameter exhaust port on the  top of the cinema projector. 
Confirm that there are no obstructions or bends in the ducting, 
all air intakes are free of obstructions, and the vane switch at 
the exit duct moves freely.
The pre-installed outside-venting  duct should be rigid at the 
cinema projector and must also  include a heat extractor and 
blower that maintains a mini...

2-10CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Installation and Setup
2.9 Install the Primary Lens
The lens seals the projection head, preventing contaminants from entering the main electronics area. Do not 
operate the cinema projector without a lens installed.  Install a lens plug when you install or transport the 
cinema projector.
1. Verify the rear safety strap or rear hold down bracket is installed.
2. Rotate the lens clam p to the open position.
3. With the UP label facing up, insert the...

Installation and Setup
CP2230 User Manual2-11020-100430-07 Rev. 1 (05-2014)
4. Adjust the location of the anamorphic lens so that the image does not shift left or right with the anamorphic 
lens in and out.
5. Adjust the location of the anamorphic lens so th e image passes through the center as much as possible 
without vignetting, reducing side or corner brightness, especially in wide angle projection.
6.  Remove the anamorphic lens and  turn the Focus knob to re-focus the primary lens. The goal is for...

2-12CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Installation and Setup
7. Install the lamp. See 7.6 Replace the Lamp for lamp replacement instructions.
2.13 Connect the Lamp Power Supply (LPS)
 When connecting the LPS and the Igniter, the black (-) power cable must be
connected to the cathode lead and the red (+)  power cable must be connected to the anode
lead. Reversing the connections ca n damage the cinema projector.
 Connect the LPS to the cinema projecto r before you connect it to AC power....

Installation and Setup
CP2230 User Manual2-13020-100430-07 Rev. 1 (05-2014)
 Use a strain relief connector on the AC supply cable to prevent the cable from
rubbing against the LPS knockout  plate and becoming damaged.
1. Connect LPS Comm unication Cables:
 a. Remove the 2 cover plate (2 thumbscrews) from  the cinema projector’s baseplate in the LVPS com-
partment.
 b. Connect one end of the RS-232 cable to the port labeled  RS232. Route the cable up through the open-
ing in the cinema projector’s...

2-14CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Installation and Setup
2. Connect the Lamp Leads: 
 a. Open the LVPS access door and remove the four hex  screws from the safety cage front panel. Lift the 
front panel over the igniter.
 b. Loosen the 6 screws to remove the LPS side panel. 
 c. Route the cables through the st rain reliefs in the LPS cover. 
 d. Connect the positive (+) and nega tive (-) lamp leads to the terminals on the LPS using a torque setting 
of 14ft/lbs (20N/m).  DANGER! In...