Christie Projector CP2230 User Manual

       Table of Contents
CP2230 User Manualv020-100430-07 Rev. 1 (05-2014)
A.1.6 Gamma ........................................................................\
........................................................ A-1
A.2 Source Signal Co mpatibility ........................................................................\
........................ ....... A-2
A.2.1 Cinema  Inputs ........................................................................\
.................................... ............

CP2230 User Manual1-1020-100430-07 Rev. 1 (05-2014)
1 Introduction
This manual is intended for professionally trained operators of Christie high-brightness projection systems. 
These operators are qualified to replace the lamp and air filter, but should not attempt to install or service the 
cinema projector.
Only accredited Christie technicians who are knowledgeab le about the hazards associated with high-voltage, 
ultraviolet exposure, and the high te mperatures generated by the cinema projector lamp...

1-2CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Introduction
watts per square centimeters of effective UV radiation. An  evaluation of your workplace is
advised to assure employees are not exposed to  cumulative radiation levels exceeding the
government guidelines for your area. 2) Be  aware that some medications are known to
increase sensitivity to UV radiation.
This cinema projector must be operated in an enviro nment that meets the operating range specification, as 
listed in  Appendix A:...

Introduction
CP2230 User Manual1-3020-100430-07 Rev. 1 (05-2014)
 Lamp may explode causing bodily harm or death. 1) Always wear protective
clothing whenever the lamp door  is open or while handling the lamp. 2) Ensure those within
the vicinity of the cinema projector are also equipped with protective clothing. 3) Never
attempt to access the lamp while the lamp is on. Wait a minimum of 10 minutes after the lamp
turns OFF turning the cinema projector off, di sconnecting it from a power source, and open-...

1-4CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Introduction
1.5 Contacting Your Dealer
If you encounter a problem with your Christie cinema projector, contact your dealer. To assist with the 
servicing of your cinema projector, enter the informat ion in the tables and keep this information with your 
records.
* The serial number can be found on the  license label located on the front panel.
Table 1.1 Purchase Record
Dealer:
Dealer or Christie Sales/Service Contact Phone Number:
cinema projector...

CP2230 User Manual2-1020-100430-07 Rev. 1 (05-2014)
2 Installation and Setup
This section explains how to install, connect, and optimize the cinema projector display.
2.1 Site Requirements
To safely install and operate the cinema projector,  the installation location must meet these minimum 
requirements:
• Physical Operati ng Environment
• Maximum Ambient Temperature (operating)  35°C
• Minimum Ambient Temperature (operating) 10°C
• External Exhaust Ducting
• The installation site must provide a minimum...

2-2CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Installation and Setup
2.3 Cinema Projector Components
Air Filter Cover and Air Filter
Filters the intake air before it circulates in the front compartment to cool the main electronics.
Manual Douser Override 
Closes the douser. Closing the douser rotates a shutter bl ade in front of the lamp and reduces lamp power to 
2kW to conserve lamp life. The override switch is meant for emergency use only. 
Exhaust Duct and Vane Switch
Extracts heated air from...

Installation and Setup
CP2230 User Manual2-3020-100430-07 Rev. 1 (05-2014)
LED Status Indicators
Provide information about the status of the cinema projector. See 5 Operation for information about cinema 
projector status.
Motorized Auxiliary Lens Mount
An optional auxiliary lens mount can be installed adjacent to the primar y lens mount to provide motorized 
positioning of a 1.25x Anamorphic lens or a 1.26 Wide  Converter lens in front of the primary lens. The Wide 
Converter lens “zooms” the image from...

2-4CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Installation and Setup
ICP Faceplate Connections
The ICP board provides the image processing electronics for the cinema projector. The ICP faceplate includes 
a number of LEDs that are only functional when  the cinema projector is in full power mode.
• REGEN:  (Regulators Enabled) Indicates the presence of th e internal regulator enable signal. When illumi-
nated BLUE the internal regulators  are enabled. When OFF, not enabled.
• SOFTST:  (Software...