Christie Digital Systems Lx41, Lw41 User Manual

ENGLISH
7LX41/LW41 Setup Guide020-000510-01 Rev. 1 (06-2012)
Connecting with your devices
Before connecting the projector to a device, consult the manual of the device to 
confirm that the device is suitable for connecting with this projector and prepare 
the required accessories, such as a cable in accord with the signal of the device. 
Consult your dealer when the required accessory did not come with the product or 
the accessory is damaged.
After making sure that the projector and the devices are...

8LX41/LW41 Setup Guide020-000510-01 Rev. 1 (06-2012)
Connecting power supply
1. Put the connector of the power cord into the 
AC IN (AC inlet) of the projector.
2. Firmly plug the power cord’s plug into the 
outlet.  In a couple of seconds after the 
power supply connection, the POWER 
indicator will light up in steady orange.
Please remember that when the DIRECT POWER ON 
function activated, the connection of the power supply make the projector turn on.
Turning on the power
1. Make sure that the power...

ENGLISH
9LX41/LW41 Setup Guide020-000510-01 Rev. 1 (06-2012)
Adjusting the projector’s elevator
When the place to put the projector is slightly uneven to 
the left or right, use the elevator feet to place the projector 
horizontally. Using the feet can also tilt the projector 
in order to project at a suitable angle to the screen, 
elevating the front side of the projector within 12 degrees.
This projector has 2 elevator feet and 2 elevator buttons. 
An elevator foot is adjustable while pushing the...

10LX41/LW41 Setup Guide020-000510-01 Rev. 1 (06-2012)
Displaying the picture
1. Activate your signal source. Turn the 
signal source on, and make it send the 
signal to the projector.
2. Use the VOLUME + / VOLUME - buttons 
to adjust the volume. 
To have the projector silent, press the 
MUTE button on the remote control.
3. Press the INPUT button on the projector. 
Each time you press the button, the 
projector switches its input port in turn.
You can also use the remote control to 
select an input...

ENGLISH
11LX41/LW41 Setup Guide020-000510-01 Rev. 1 (06-2012)
NOTE  • The ASPECT button does not work when no proper signal is inputted.
• For the details of how to adjust the picture, please see User Manual - 
Operating Guide. 
CAUTION  ►If you wish to have a blank screen while the projector's lamp is 
on, use one of methods below.
- Use the supplied lens cover.
- Use the BLANK function (see User Manual - Operating Guide).
Taking any other action may cause the damage on the projector.
Turning off...

12LX41/LW41 Setup Guide020-000510-01 Rev. 1 (06-2012)
Replacing the lamp
A lamp has fi nite product life. Using the lamp for long periods of time could cause 
the pictures darker or the color tone poor. Note that each lamp has a different 
lifetime, and some may burst or burn out soon after you start using them.
Preparation of a new lamp and early replacement are recommended. To prepare 
a new lamp, make contact with your dealer and tell the lamp type number.
Type number : 003-120730-01  
(DT01175) 
1....

ENGLISH
13LX41/LW41 Setup Guide020-000510-01 Rev. 1 (06-2012)
 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
WARNING  ►The projector uses a high-pressure mercury glass lamp. The 
lamp can break with a loud bang, or burn out, if jolted or scratched, handled 
while hot, or worn over time. Note that each lamp has a different lifetime, and 
some may burst or burn out soon after you start using them. In addition, if the 
bulb bursts, it is possible for shards of glass to fly into the lamp housing, and 
for gas...

14LX41/LW41 Setup Guide020-000510-01 Rev. 1 (06-2012)
Cleaning and replacing the air fi lter
Please check and clean the air fi lter periodically. When the indicators or a 
message prompts you to clean the air fi lter, comply with it as soon as possible.
The air fi lter of this projector consists of a fi lter cover and a fi lter unit with two 
types of fi lter. If one or both of the fi lters are damaged or heavily soiled, replace 
the fi lter unit with a new one.
Request for a fi lter unit with the following type...

ENGLISH
15LX41/LW41 Setup Guide020-000510-01 Rev. 1 (06-2012)
Cleasning and replacing the air filter  (continued)
10. Put the filter cover back into the place.
11 . Turn the projector on and reset the filter time using the FILTER TIME item 
in the EASY MENU.
(1)  Press the MENU button to display a menu.
(2)  Point at the FILTER TIME using the ▲/▼ cursor buttons, then press the 
► cursor (or the ENTER / the RESET) button. A dialog will appear.
(3)  Press the ► cursor button to select the “OK” on the dialog....

16LX41/LW41 Setup Guide020-000510-01 Rev. 1 (06-2012)
Replacing the internal clock batter y
This projector has internal clock that uses a battery. When 
the clock of the network function does not work correctly, 
please try solution by replacement of the battery: HITACHI 
MAXELL or HITACHI MAXELL ENERGY, part number 
CR2032 or CR2032H.
OPEN
CLOSE
OPEN
CLOSE
OPEN
CLOSEOSELOSE
OPEN
CLOSE
Raised dot
BatteryKnob
Battery
Cover
1. Turn the projector off, and unplug the power cord. Allow 
the projector to cool...