Canon scanner imageFORMULA DRM1060 User Manual

21
Displayed Error Codes
When a scanning error occurs, the following error codes are displayed 
in the Job No. Indicator.
Other Displays
When the straight path tray is opened or closed, the eject method is 
displayed in the Job No. Indicator.: displayed when the upper unit is open.
: displayed when a paper jam is detected.
: displayed when a double feed is detected while scanning.
: displayed when skewed documents, staples, or feed errors are 
detected.
: displayed for other errors.
: flashes during...

22
Basic Operation
Documents
The scanner can scan documents ranging in size from business cards 
to A3. (Up to A1 size is possible with folio scanning in Long Document 
mode.) The document sizes that this scanner can scan are shown 
below.
Plain Paper
Size
Width:  50.8 mm to 300 mm (2 to 11.8)
Length:  70 mm to 432 mm (2.8 to 17)
Up to 3,000 mm (118.1) in Long Document mode
Paper thickness
U-turn path (page separation):
27 to 128 g/m
2 (0.04 to 0.15 mm)
U-turn path (bypass):
27 to 164 g/m
2 (0.04 to 0.2...

23
• Laminated documents may not be scanned correctly, depending on the document.
 It is recommended that thin documents be fed one page at a time.
 Scanning the following types of documents can cause a paper jam  or malfunction. To scan such a document, make a photocopy of the 
document and then scan the photocopy.
Business Card Size: Width: 50.8 mm to 55 mm (2 to 2.2) Length: 85 mm to 91 mm (3.4 to 3.6)
Paper thickness: 128 to 380 g/m
2 (0.15 to 0.45 mm)
Orientation: Vertical feeding only
Eject...

24
How to Place Documents
Switching the Feed and Eject 
Methods
Switch the feed and eject methods based on the type of document you 
are scanning.Standard feeding is used to feed documents one page at a time. Non 
separation feeding is used to feed bound or fastened multi-page 
documents or folded documents without separating them.
Feed and Eject Methods for Different Document Types
Hint
When scanning documents that contain both plain paper and plastic 
cards, place the cards at the top and use the...

25
Placing Documents
1Switch the feed method based on the type of document 
you are scanning.
When scanning plain paper or business cards, set the feed 
selection lever to the standard feeding position (lower position). 
The pages of a multi-page document will be separated and fed 
one page at a time.
When scanning bound or fastened paper (e.g., invoices), set the 
feed selection lever to the non separation feeding position (upper 
position). As documents are scanned without page separation, 
place the...

26
When scanning documents longer the LTR horizontal (216 mm), 
extend the feed support and eject support extensions.
5Adjust the document guides to fit the width of the 
document to be scanned.
6Place the document.
After placing the document, align the document guides with both 
edges of the document.
IMPORTANT
 When placing documents into the feed tray, take care not to cut 
your hand on the edges of the paper.
 Make sure that the document does not exceed the loading limit 
marks ( ) on the document...

27
 After you finish scanning, close the document feed tray, document 
eject extension support, and straight path tray to prevent damage 
to the scanner while it is not being used.
 When scanning multi-page documents that are fastened together 
(e.g., invoices), place the document so that the fastened edge is 
toward the feed tray.
 Be careful when scanning paper that is longer than A3 size or thin 
paper, as the documents may fall off of the eject tray after scanning.
 When using the straight path,...

28
3Fold the document in half.
Crease the document firmly down its center to fold the document 
in half. Fold the document so that its edges are neatly aligned. If 
the document is not folded properly, paper jams may occur or 
distortions may appear in the combined scanned image.
IMPORTANT
A portion of the scanned image will be missing at the fold line.
4Place the document with the folded edge facing right.
After placing the document, align the document guides with both 
edges of the document.
IMPORTANT...

29
1Start Windows and log in as a user with administrator 
privileges.
2Click the Start button, and then click [All Programs], 
[Canon DR-M1060], and [Canon imageFORMULA Utility].
Hint
Canon imageFORMULA Utility is registered to the following 
location in Windows 8.1.
imageFORMULA Utility starts.
3Click [CANON DR-M1060 USB] and click [Properties].
Scanner properties are displayed.
4Click the [Maintenance] tab, and then select a Long 
Document mode.
Select [Long Document Mode (1000 mm)] or [Long Document...

30
Detecting a document double feed
This scanner includes a function to detect document double feeds. By 
using this function, the scanner will automatically stop when it detects 
that multiple documents have been fed at the same time. You can also 
specify whether to save the scanned image after scanning has 
finished and continue scanning the document (double feed detection 
ignore function).
To use the double feed detection function, you must first open the 
scanner driver settings screen and enable...