Canon scanner imageFORMULA DR6010C User Manual

							Chapter 3  Basic Operation
3-31
 When scanning in the Long Document mode, if the document is placed on the scanner in a 
skewed position, it may be damaged. Be careful to place the document so that it is not 
skewed.
 When scanning with the Long Document mode, paper jam detection may react slowly, 
resulting in damage to the document. Be careful to avoid paper jams.
 When scanning long documents, make sure to feed them one page at a time with the 
bypass mode.
Long Document Mode Settings
Follow the procedure below to set the Long Document mode.
1Use the following procedure to open the [CANON DR-6010C USB Properties] (or [CANON 
DR-6010C SCSI Properties].)
1. Click the start button and click [Control Panel].
2. Click [Devices and Printers].
Note
Under Windows Vista, click [Hardware and Sound] - [Scanners and Cameras].
Under Windows XP, click [Printers and Other Hardware] - [Scanners and Cameras]. 
						

							Chapter 3  Basic Operation
3-32
3. Right-click [CANON DR-6010C] and click [Scan properties].
Note
Under Windows Vista/XP, select [CANON DR-6010C USB] or [CANON DR-6010C SCSI] and 
click [Proper ties].
The [CANON DR-6010C USB Properties] or [CANON DR-6010C SCSI Properties] 
window appears. 
						

							Chapter 3  Basic Operation
3-33
2Click the [Maintenance] tab.
3Click [Long Document mode (1,000 or 3,000 mm)].
4Click [OK] to close [CANON DR-6010C USB Properties].
5Turn the scanner OFF and then ON again.
IMPORTANT
 If you are using a SCSI connection, turn OFF the computer and then turn the scanner OFF 
and then ON again.
 Wait at least 10 seconds before turning the scanner back ON after it has been turned OFF.
MultiStream Function
If the application that you are using supports the MultiStream function, then it is possible to scan a 
document once and simultaneously output two types of images (Primary image and Secondary 
image.) 
CapturePerfect 3.1 supports the MultiStream function. The following settings are possible. 
 You can set the Primary or Secondary image and Front or Back for the Image Type (mode), 
Resolution or Drop Out Color.
 You can change the File Type for the Primary image and the Secondary image. However, 
you cannot change Front or Back from File Type. 
						

							Chapter 3  Basic Operation
3-34 Note
 When using the MultiStream function, “Auto Color Detection,” “Prevent Bleed Through,” 
“Prescan,” and “Batch Separation by Patchcode Sheet” cannot be set.
 The MultiStream function is not available when “Auto Color Detection” is selected for the 
Mode setting in the ISIS/TWAIN driver.
Auto Power OFF Function
This scanner includes an Auto Power OFF function. When this function is enabled, the scanner will 
turn OFF automatically if no operations are performed for 4 hours.
Depending on your country or region, the Auto Power OFF function may be enabled under factory 
default conditions.
The setting of the Auto Power OFF function can be changed as follows.
1Use the following procedure to open the [CANON DR-6010C USB Properties] (or [CANON 
DR-6010C SCSI Properties].)
1. Click the start button and click [Control Panel]. 
						

							Chapter 3  Basic Operation
3-35
2.Click [Devices and Printers].
Note
Under Windows Vista, click [Hardware and Sound] - [Scanners and Cameras].
Under Windows XP, click [Printers and Other Hardware] - [Scanners and Cameras].
3. Right-click [CANON DR-6010C] and click [Scan properties].
Note
Under Windows Vista/XP, select [CANON DR-6010C USB] or [CANON DR-6010C SCSI] and 
click [Proper ties]. 
						

							Chapter 3  Basic Operation
3-36
The [CANON DR-6010C USB Properties] or [CANON DR-6010C SCSI Properties] 
window appears.
2Click the [Maintenance] tab.
3Set the Auto Power OFF Function. 
						

							Chapter 3  Basic Operation
3-37
If the [Turn off automatically after 4 hours] check box is selected, the Auto Power OFF 
function is enabled and the power turns off automatically after four hours pass without 
scanning or other operation.
If the [Turn off automatically after 4 hours] check box is deselected, the Auto Power OFF 
function is disabled.
Note
Under the following circumstances, the Auto Power OFF function does not operate even if the 
[Turn off automatically after 4 hours] check box is selected.
 If any document remains in the feeder after scanning
 If a scanner error occurs
4Click [OK] to close [CANON DR-6010C USB Properties].
5Turn the scanner OFF and then ON again.
IMPORTANT
 If you are using a SCSI connection, turn OFF the computer and then turn the scanner OFF 
and then ON again.
 Wait at least 10 seconds before turning the scanner back ON after it has been turned OFF. 
						

							4-1
Chapter 4Maintenance
4-1 Regular Maintenance
Clean the scanner on a regular basis as described below to maintain peak scanning quality.
CAUTION
■When cleaning the scanner, turn OFF the power switch and disconnect the power 
cord from the power outlet.
■Do not use excessive force when removing or attaching the rollers. Doing so may 
damage them.
■Do not use spray type cleaners to clean the scanner. Precision mechanisms, such 
as the light source, may get wet, and cause a malfunction.
■Never use paint thinner, alcohol, or other organic solvents to clean the scanner. 
Such solvents can damage or discolor the exterior of the scanner, or create a risk 
of fire or electrical shock.
Cleaning the Scanner
To clean the exterior of the scanner, dampen a cloth with water or a mild detergent, wring the cloth 
out thoroughly, and then wipe the dir t away. Then use a dry, soft cloth to wipe away any moisture.
Cleaning the Feed Path
Dust or paper particles in the document feed opening or inside the scanner can cause lines in 
scanned images. Use compressed air to periodically clean dust and paper particles from the 
document feed opening and the inside of the scanner. After finishing a large scanning job, turn OFF 
the scanner and then clean out any paper particles. 
						

							Chapter 4  Maintenance
4-2
Cleaning the Sensor Glass and the Rollers
If scanned images have extraneous marks, or if the scanned documents are dirty, the sensor glass 
or rollers inside the scanner may be dirty. Clean them periodically.
1Carefully open the upper unit until it stops.
IMPORTANT
When opening the upper unit, do not grasp the roller unit in the center. Doing so may distort 
the rollers and lead to feeding errors.
Note
The location of the sensor glass and various rollers are shown below.
2Use compressed air to keep the interior of the scanner free of dust and paper particles.
Retard RollerRollers Sensor GlassesRoller Unit 
						

							Chapter 4  Maintenance
4-3
3Use a clean dry cloth to wipe dirt off the sensor glass. 
Wipe both the top and bottom sensor glasses.
IMPORTANT
Scratches on the sensor glass may cause marks on the images and could cause feeding 
errors. If there are scratches on the sensor glass, contact your local authorized Canon dealer 
or service representative.
4Dampen a cloth with water, wring it out thoroughly, and then wipe the rollers of the upper unit 
while turning them.
Do not try to turn the rollers in the lower part of the scanner. Clean these rollers simply by 
wiping the exposed part.
IMPORTANT
 Do not use detergent to clean the rollers, since any detergent remaining on the rollers could 
cause a feeding error.
 Do not try to turn the rollers in the lower part of the scanner. Turning these rollers by force 
may damage them and lead to feeding errors.
5Remove the roller unit and the retard roller. (See “Removing the Roller Unit,” on p. 4-8, and 
“Removing the Retard Roller,” on p. 4-11.)
Clean while turning
Clean only 
exposed part