Canon scanner imageFORMULA DR6010C User Manual

							Chapter 2  Setup
2-6
4Click [Install].
Installation of the DR-6010C driver begins.
5Click [Next].
The software license agreement appears.
6Read the license agreement and click [Yes] to accept it.
The DR-6010C driver is installed.
Next, the job tool software is installed. 
						

							Chapter 2  Setup
2-7
7The DR-6010C driver installation is complete.
8Click [Finish].
Installation of CapturePerfect 3.1 starts.
9Click [Next].
The software license agreement appears. 
						

							Chapter 2  Setup
2-8
10Read the agreement and click [I accept the terms of the license agreement] to accept it, then 
click [Next].
11To install the Microsoft SharePoint plug-in, select the [Microsoft SharePoint Plug-in] check 
box, and then click [Next].
12Click [Next].
CapturePerfect is installed.
13The CapturePerfect installation is complete. 
						

							Chapter 2  Setup
2-9
14Click [Finish].
Installation of the User Manual starts.
15Click [Next].
The User Manual is installed.
16The User Manual installation is complete.
17Click [Finish].
The installation completion screen appears. 
						

							Chapter 2  Setup
2-10
18Click [Exit].
Click [Back] to return to the menu screen.
19After the software installation is complete, you can connect the scanner to the computer.
(See “2-4 Connecting the Scanner to the Computer,” on p. 2-11.) 
						

							Chapter 2  Setup
2-11
2-4 Connecting the Scanner to the Computer
There are two methods for connecting the DR-6010C scanner to a computer: USB connection, 
which makes use of a standard USB port on the computer, and SCSI connection, which makes use 
of a SCSI card installed in an expansion slot of the computer. Select the method that is suitable for 
your computer environment.
CAUTION
Do not connect a USB cable and SCSI cable at the same time.
Using a USB Connection
1Verify that the power switch of the scanner is OFF.
If the power switch is in the ON position, push the switch to set it to OFF.
2Plug the supplied power cord into the power connector on the back of the scanner. a
SCSI ID DIP Switches
USB Connector
SCSI Connector  
(half-pitch 50-pin, pin-type)Power Connector
Powe r  sw it c h
OFF position ON position 
						

							Chapter 2  Setup
2-12
3Connect the power cord into an AC outlet. b
4Use the supplied USB cable to connect the scanner to the computer.
Using a SCSI Connection
IMPORTANT
 Make sure that the computer is turned OFF before connecting the SCSI cable. If the cable is 
connected while the computer is on, the scanner may not be properly recognized by the 
computer.
 A SCSI cable is not supplied with the scanner. Purchase a cable that is suitable for the 
scanner and for the SCSI connector on the computer.
 The SCSI ID of the scanner is set to “SCSI ID = 2” by default. When using a daisy-chain 
configuration with other SCSI devices, set the DIP switches so that there is no duplication of 
SCSI ID numbers in the system.
 The DR-6010C scanner incorporates a SCSI terminator which is permanently set to ON. 
When using a daisy-chain configuration with other SCSI devices, make sure that the DR-
6010C is connected as the last device in the chain. Set the terminators of all other devices 
to OFF.
Ty p e  A
Ty p e  B
symbol on plug should face down
DIP switches
Factory default (SCSI ID = 2) 
						

							Chapter 2  Setup
2-13
1Shut down Windows and turn the computer OFF.
2Verify that the power switch of the scanner is OFF.
If the power switch is in the ON position, push the switch to set it to OFF.
3Plug the supplied power cord into the power connector on the rear of the unit. a
4Connect the power cord into an AC outlet. b
5Use the SCSI cable to connect the scanner to the computer.
Powe r  sw it c h
OFF position ON position
120 V Ty p e
220-240 V Type 
						

							Chapter 2  Setup
2-14
2-5 Turning the Power ON
When you turn the computer and the scanner ON, the Plug and Play function of Windows 
recognizes the scanner and automatically installs the required device driver.
IMPORTANT
 When connecting the scanner to the computer using a SCSI cable, be sure to turn power to 
the scanner ON first, and then turn power to the computer ON. If you turn power to the 
computer ON first, the scanner may not be properly recognized by the computer.
 If you turn the power OFF, wait at least 10 seconds before turning it ON again.
 If you will not be using the scanner for an extended period, you should disconnect the power 
cord from the AC outlet for safety.
Scanner Recognition
The scanner will be recognized the first time it is connected to the computer.
1Make sure that the scanner and computer are connected properly.
2Press the power switch to turn the scanner ON.
The power indicator lights green.
3Turn the computer ON.
4Log onto Windows with an account that has Administrator privileges.
5Windows recognizes the DR-6010C automatically, and installation of the device driver begins.
Windows 7/Vista
Windows XP
Pow er  sw i t ch
Power indicator
ON 
						

							Chapter 2  Setup
2-15 Note
 In Windows 7/Vista and Windows XP, a message appears when installation is complete.
 The DR-6010C is installed in Device Manager under [Imaging Devices] as [CANON DR-
6010C USB] or [CANON DR-6010C SCSI].
About Auto Power OFF Function
This scanner includes an Auto Power OFF function. When this function is enabled, the 
scanner will turn OFF automatically if no operations are performed for 4 hours.
The setting of the Auto Power OFF function can be changed as necessary. (See “Auto Power 
OFF Function,” on p. 3-34.)
Note
Depending on your country or region, the Auto Power OFF function may be enabled under 
factory default conditions.
IMPORTANT
The scanner’s power switch remains in the ON position even after the power is turned off by 
the Auto Power OFF function. To turn the power back on again, turn off the power switch and 
then turn it back on again. When doing this, wait at least 10 seconds after operation of the 
Auto Power OFF function before turning the power back on again.