Canon Projector WUX500 User Manual

111
Menu Description
Advanced Guide
Menu Description
Wireless Networks
• Projector Access Point (PJ AP) Mode
The projector can be used as an access point for direct communication with 
wireless LAN-compatible computers.
Up to five computers can be connected at once.
The following network features are available in PJ AP mode.
• Web features
• NMPJ features (networked screen projection)
• User commands
Other network features (specifically, SNMP, PJLink, Mail, AMX, Crestron RoomView and 
Firm Update) are...

Menu Description
112
• Infrastructure Mode
The projector can also be used as a wireless LAN client for connections to a 
wireless LAN access point.
In this case, the projector is connected to computers via the wireless LAN access 
point.
•Wired LAN features and wireless infrastructure mode cannot be used at the 
same time.
•Wireless LAN features are not available in standby mode.
•PJ AP and infrastructure modes cannot be used at the same time.
•Wired LAN and PJ AP mode cannot be used in the same...

113
Menu Description
Advanced Guide
Menu Description
•When you connect the computer to the network for the first time, it is also 
necessary to perform settings on the computer. In this case, consult the network 
administrator regarding the necessary settings.
In a network environment where a DHCP server is operating, choose [On] on the 
projector [DHCP] screen to enable the DHCP function and connect it. (P119, P123) 

Menu Description
114
Wireless LAN (Wi-Fi)
■Countries and Regions Where Wireless LAN Use Is 
Permitted
Use of the wireless LAN function is restricted under the laws, etc., of each country 
and region, and violation of these restrictions may be subject to punishment. Check 
the Canon website for a list of countries and regions where use of the wireless LAN 
function permitted. 
Canon assumes no responsibility whatsoever for problems, etc., that may arise 
from use of the wireless LAN function in countries...

115
Menu Description
Advanced Guide
Menu Description
Statement on EC directive
Please contact the following address for the original Declaration of Conformity:
CANON EUROPA N.V.
Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
Canon Inc. tímto prohlašuje, že tento ZC-ST je ve shodě se základními požadavky a dalšími 
příslušnými ustanoveními směrnice 1999/5/ES.
Undertegnede Canon Inc. erklærer herved, at følgende udstyr ZC-ST...

Menu Description
116
Completing Projector Settings
Settings described in this section apply to wired and wireless network 
connections, setting a network password, and other aspects of networked 
projection.
(When the input signal is Analog PC-1)
*Only available for wired connections.
MenuFunctionDetails
Network settings lock Lock network settings to prevent changes.P117
Network password 
settingSpecify whether network settings are password-
protected.P117
Register network 
passwordSet a network...

117
Menu Description
Advanced Guide
Menu Description
Network settings lock
> [Network Settings] > [Network settings lock] 
You can lock/unlock the network settings so that they cannot be changed.
Network password setting
> [Network settings] > [Network password setting] 
You can set whether or not a password is required in order to change the projector 
network settings.
Register network password
> [Network settings] > [Register network password] 
Use the [ ] / [ ] / [ ] / [ ] buttons to enter the...

Menu Description
118
Network standby settings
> [Network settings] > [Network standby settings] 
Specify the operating status of wired network functions in standby mode.
Network (wired/wireless)
> [Network settings] > [Network (wired/wireless)] 
Enable or disable wired or wireless network connectivity and the mode of operation.
Specifying [Off] can save energy.
OptionFunction
NormalAll network functions are available even in standby mode, 
including the web screen, control over the network, and PJLink....

119
Menu Description
Advanced Guide
Menu Description
Detailed settings (wired)
> [Network settings] > [Detailed settings (wired)] 
Display and manually change the wired IP address, gateway address, and other 
settings. Available only when wired networking is [On].
MenuFunction
IP address Wired IP address of the projector.
Gateway address Wired gateway address of the projector.
MAC address Wired MAC address of the projector.
DHCP
TCP/IP settingsChange or specify the IP address, subnet mask, and gateway...

Menu Description
120
Network setting 
initializationThe following network settings are initialized.
Settings configured from the projector menu
•Network settings lock (P117)
•Network password setting (P117)
•Register network password (P117)
•Network standby settings (P118)
•Network (wired/wireless) (P118)
•Detailed settings (wired) (P119)
-IP address (wired) (P119)
-Gateway address (wired) (P119)
-DHCP (wired) (P119)
-Subnet mask (wired) (P119)
•PJLink (P124)
•AMX Device Discovery settings (P125)...