Canon Projector WUX500 User Manual

141
Menu Description
Advanced Guide
Menu Description
Setting Errors
When a setting-related error occurs, the error name is displayed on the screen, and 
a “!” mark is displayed next to the input field which caused the error.
The error meanings are as shown below.
ErrorMeaning
Input error A setting outside the valid range was set on the 
settings screen.
Password setting error The set password and confirmation password did 
not match.
Invalid SMTP The SMTP server IP address has not been set.
System failed...

Menu Description
142
Resetting Network Settings to the Default Settings
1Perform steps 1 - 3 on “Displaying the Network Configuration Screen” 
(P128) to display the settings screen.
2Click [Initialize].
3A confirmation window appears. Click [OK].  

143
Menu Description
Advanced Guide
Menu Description
■Error Notification Mails
The messages shown in the following error list are sent when an error occurs in the 
projector.
Error list
Errors related to 
temperatureError name Temperature abnormality
Text The temperature inside the projector is too high for some 
reason or the outside air temperature is higher than the 
specified one.
If the problem is inside the projector, check whether the 
projector is installed and operated normally, turn off the...

144
Menu Description
Controlling the Projector from a Computer
The projector can be controlled from a computer over a wired or wireless network 
connection.
1Turn on the computer and projector.
2Launch a web browser, enter “http://(projector IP address)” in the 
address bar, and press the Enter key. The projector web screen appears.
3Click [Projector control] on the web screen.The password input window appears.
4Enter the user name and password on the password input window, then 
click [OK].
The factory...

145
Menu Description
Advanced Guide
Menu Description
5When the operations are finished, click [Back to top] to return the initial 
web screen.
Split screen Select the setting for split-screen mode and click [Apply] to switch to \
split-screen projection. ( P77, P156 )
Split screen 
control Select the control rights setting for split-screen mode and click [Apply] 
to switch the side currently under control. (
P77)
Information The control results and control error information are displayed at the  top of...

Menu Description
146
Checking Projector Information
You can check information about the signal types of the images projected 
and other information.
* The values are not displayed when network functions are [Off].
MenuFunction
Model name Shows the model name.
Input signalDetails of the input signal currently selected 
Information such as the type, resolution, frequency, and color 
format of the signal is displayed.
Firmware Current firmware version
Serial no. Serial number unique to this projector
IP...

147
Menu Description
Advanced Guide
Menu Description
Some values may not be displayed, depending on whether wired or wireless 
functions are enabled or disabled. ( : displayed, ×: not displayed)
Item
Wired/WirelessOff/OffOn/OffOn/On
(Pj AP)Off/On
(Pj AP)Off/On 
(Infra)
IP address (wired) × × ×
IP address (wireless) × ×
E-mail sender address ×
E-mail recipient address ×
Projector name ×
Comments × 

148
Advanced Projection
Projecting Images on a USB Flash Drive
JPEG images stored on a USB flash drive connected to the projector can be 
projected as follows. Individual images can be selected for projection, or you can 
project all images in a slideshow. JPEG images up to 10912×8640 can be 
projected.
1Insert the USB flash drive in the USB port.
Either connect the USB flash drive directly to the projector’s USB port or use a 
USB cable to connect a USB multi-card reader. USB flash drives connected via...

149
Advanced Projection
Advanced Guide
Advanced Projection
3Select a file to project.
4Switch to other images as needed.
To switch to the previous image, press the [ ] button.
To switch to the next image, press the [ ] button.
To rotate images left 90°, press the [ ] button.
To rotate images right 90°, press the [ ] button.
5After projection is finished, remove the USB flash drive.
Motion blur reduction is not available when projecting JPEG files on a USB flash drive. 
(P104)
The projector can also play...

Advanced Projection
150
Description of USB File Browser
If a USB flash memory is connected to the projector, the USB file browser appears.
In the USB file browser, you can select the image file to be projected by operating 
the file list in the USB memory device.
(1) List title
Identifies the current USB flash 
drive and number of pages in the 
file list displayed. (Current page 
number/total number of pages)
(2) Drive/file list
Lists recognized USB flash drives 
and files in folders on the drive, by...