Canon Projector WUX500 User Manual

91
Menu Description
Advanced Guide
Menu Description
Vertical projection
You can ensure adequate cooling by switching the fan mode to suit upward- or downward-
facing installations.
OptionFunction
Off Does not alter the fan mode.
Upward Setting for use when the projector faces upward.
Downward Setting for downward projection.
Edge blending
Brightness and colors of overlapping edges of images from multiple projectors, which form a 
blending area, can be adjusted for a more seamless appearance. For detailed...

Menu Description
92
SubmenuFunction
SideLeft / Right / 
To p  /  B o t t o mSelect the direction of the blending area to adjust.
WidthSpecify the width between the start and end markers.
Start 
positionMoves the position of the start marker.
Color blending 
adjustmentAdjust unwanted colors or discrepancies between colors in the blending 
area.
• Large blending areas may cover input signal dialog boxes and 
other interface elements. In this case, momentarily set edge 
blending to [Off] and check the...

93
Menu Description
Advanced Guide
Menu Description
SubmenuFunction
Black level 
adjustmentBecause black is lighter in the blending area than in other areas, you can 
adjust the black level outside the blending area to make this difference in 
brightness less noticeable.
Off
Do not adjust the black level.
Area
Adjust areas C - A to smoothen the boundaries of the blending area.
Black level adjustment
Adjust the black level brightness and color of areas B and D.
MarkerShow the blending area markers.
Reset...

Menu Description
94
Screen color
> [Install settings] > [Screen color] 
You can adjust the color quality of the images projected according to the color of 
the projection screen.
On screen
> [Install settings] > [On screen] 
Specify display details for on-screen menus, help, and warning or precaution icons.
SubmenuFunction
Corner adjustmentCorrect image distortion by aligning corners of the blending area with the 
image from the reference projector. For multi-projection alignment, align 
the corners with...

95
Menu Description
Advanced Guide
Menu Description
Menu position
Reposition menu display.
Use the [ ] / [ ] / [ ] / [ ] buttons to move the menu to the desired position.
Guide
Shows the guide screen.
OptionFunction
Off Hides the guide screen.
On Shows the guide screen.
Show input status
Specify whether signal status is shown when there is no signal or when you are completing 
signal settings.
OptionFunction
Off The input status is not displayed.
On The input status is displayed.
Overheat warning...

Menu Description
96
Test pattern
> [Install settings] > [Test pattern] 
You can project a test pattern (P176) to check resolution, color, and other details 
even without supplying an input signal. 
Lamp warning display
Specify whether to show a lamp replacement message after the lamp has been used for a 
specified period.
OptionFunction
Off The prepare lamp message and the lamp warning are not displayed.
On The prepare lamp message and the lamp warning are displayed.
Air filter warning display
A message...

97
Menu Description
Advanced Guide
Menu Description
System settings
Customize projector and remote control operation, beeping, and other 
details after startup, during standby, and in other situations.
(When the input signal is Analog PC-1)
MenuFunctionDetails
User screen settingsCustomize user screens shown at startup, when no 
signal is detected, and in other situations.P98
Interface settingsSpecify interface details such as settings for input 
signals of connected equipment.P99
Power management...

Menu Description
98
User screen settings
> [System settings] > [User screen settings] 
Capture a logo and specify logo display settings.
Logo capture
Registers the current image as a user logo. Registered user logos can be shown when no 
signal is received, when the BLANK button is pressed, or as the startup image.
OptionFunction
OKDisplay the image for logo registration.
Align the image with the red boundary lines indicating the portion that 
will be stored, and then press the OK button. The portion of...

99
Menu Description
Advanced Guide
Menu Description
Interface settings
> [System settings] > [Interface settings] 
Specify interface details such as settings for input signals of connected equipment.
Projector on
Select a logo to show after startup while the projector is warming up.
OptionFunction
Skip Project input signals immediately after startup.
Canon logo Displays the Canon logo that was registered in advance at the factory.
User logo The user logo is projected.
Key repeat
Key repeat enables...

Menu Description
100
Remote control channel
Separate channels can be assigned to up to four projectors so that a single remote control 
can be used with each projector.
Selecting the Projector Channel
If an optional wired remote control (RS-RC05) is used, there is no need to set the remote 
control channel.
OptionFunction
Ch1
Ch2
Ch3
Ch4Select the remote control channel to use with this projector.
Independent Can be controlled from a remote control set to any channel.
Selecting a Channel on the Remote...