Canon Projector WUX500 User Manual

41
Installation Procedure
Basic Guide
Installation Procedure
■Installation Tilted Upward
To correct keystone distortion when the projector is tilted upward (using adjustable 
feet, for example), perform keystone correction (P62) or corner adjustment (P63).
■Installation on High Surfaces
For projection from a shelf or other high surface, the projector can be installed 
upside-down and the projected image inverted. In this case, attach the option feet 
on top of the projector.
Attaching Option Feet...

Installation Procedure
42
Removing hole caps labeled (2) 
Open the lamp cover and use a screwdriver or similar tool to 
push off the caps from below.
■Ceiling Mounting or Rear Projection
You can mount the projector on the ceiling (ceiling mounting) with it turned upside 
down or place it behind the screen (rear projection) if you use a translucent screen.
Make sure to use the optional ceiling attachment. For the ceiling attachment, refer 
to “Option” (P195). For details, refer to the assembly and...

43
Installation Procedure
Basic Guide
Installation Procedure
Relationship between Projecting Distance and 
Image Size
The size of projected images is determined by zooming, relative to the distance 
from the projector to the screen. (Optical zooming on the WUX500, and electronic 
zooming on the WUX450ST.) Refer to the following table and decide the distance 
between the projector and screen.
WUX500Projection distance [m (feet)]
WUX450STProjection distance [m (feet)]
Image Size 
(Dia.)16:10 16:9 4:3
Wide...

Installation Procedure
44
Lens Shift Function
You can reposition the image in all directions by turning the lens shift dials on the 
side of the projector, which moves the lens up, down, left, or right. For instructions, 
refer to “Adjusting the Image Position” (P56).
■Amount of Lens Shift
The amount of lens shift is indicated as a percentage relative to the image height 
and width. The lens shift ranges for the projector are as follows.
The lens can be shifted up and to the left or right. Performance...

45
Installation Procedure
Basic Guide
Installation Procedure
WUX500[cm (in)]
WUX450ST[cm (in)]
Image size 
(Dia.)16:10 16:9 4:3
ABABAB
40 32 (12.6)9 (3.5)30 (11.8)9 (3.5)37 (14.6)8 (3.1)
60  48 (18.9) 13 (5.1) 45 (17.7) 13 (5.1) 55 (21.7) 12 (4.7)
80 65 (25.6)17 (6.7)60 (23.6)18 (7.1)73 (28.7)16 (6.3)
100  81 (31.9) 22 (8.7) 75 (29.5) 22 (8.7) 91 (35.8) 20 (7.9)
150 121 (47.6)32 (12.6)112 (44.1)33 (13.0)137 (53.9)30 (11.8)
200  162 (63.8) 43 (16.9) 149 (58.7) 44 (17.3) 183 (72.0) 41 (16.1)
250 202...

46
Connection Procedure
Connecting a Computer
Before connecting the projector to other equipment, turn off both the projector 
and the other equipment.
Amplified 
speakers
Mini jack RCA terminal
Audio cable 
(not included)
AUDIO OUT 
terminalANALOG PC-1 / 
DVI-I terminal
AUDIO IN 1 
terminal
Audio cable
(not included)DVI-I - D-Sub cable
(not included)DVI-I cable 
(not included)
AUDIO output 
terminalMonitor output 
terminal 
(Mini D-sub 15-pin)Monitor output 
terminal 
(DVI terminal)
ComputerAudio cable...

47
Connection Procedure
Basic Guide
Connection Procedure
Connecting a Computer (continued)
Computer
AUDIO output terminalMonitor output terminal 
(Mini D-sub 15-pin)
Audio cable 
(not included)
Computer cable
(not included)or
BNC cable 
(not included)
Mini D-sub 15-pin - BNC 
terminal converter cable 
(not included)
HDBaseT terminal
HDMI terminal
AUDIO IN 2 
terminalANALOG PC-2 / 
COMPONENT terminal
LAN cable
(CAT5e or better; shielded;
not included)
HDBaseT 
transmitter HDMI cable
(not included) HDMI...

Connection Procedure
48
Connecting AV Equipment
Amplified 
speakers
Mini jackRCA 
terminal
Mini jackRCA 
terminalAV equipment
D terminalRCA component 
terminal
Audio 
cable
(not 
included)Audio 
cable 
(not 
included)D terminal 
plug - RCA 
plug 
component 
conversion 
cable (not 
included)RCA plug - 
RCA plug 
component 
cable (not 
included)
Component cable 
(not included)
HDBaseT terminal
HDMI terminal
AUDIO IN 2 
terminalANALOG PC-2 / 
COMPONENT terminal
AUDIO OUT 
terminalLAN cable
(CAT5e or better;...

49
Connection Procedure
Basic Guide
Connection ProcedurePlugging the Projector In
Connect the power cord to the projector and plug it in.
Notes on HDBaseT
• Use a shielded cable rated at CAT5e or better.
• Maximum transmission distance is 100 m.
• However, maximum transmission distance may be shorter in some environments.
• Do not use the LAN cable when it is coiled or bundled.
• Inserting or removing the LAN cable during projection may cause noise.
• Connectivity with all HDBaseT transmitters on the...

50
Projection Procedure
Step 1 Turn the Projector On
1Check the connection between the projector and the computer or AV 
equipment. (P46 - P48)
For instructions on connecting the power cord, refer to “Plugging the Projector 
In” (P49).
2Press the POWER button.
The [POWER ON] indicator initially flashes green, after which it remains lit.
The countdown window is displayed for approximately 20 seconds, and then 
the projection is started. Press the OK or EXIT button to hide the countdown 
window.
3Turn on...