Canon Projector WUX500 User Manual

11
Safety Instructions
Safety Instructions
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirements for use in 
the country you purchased it.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND 
EASILY ACCESSIBLE.AC Power Cord for the United States and Canada:
The AC Power Cord used in the United States and Canada is 
listed by the Underwriters Laboratories (UL) and certified by 
the Canadian Standard Association (CSA).
The AC Power Cord has a...

Safety Instructions
12
Federal Communication Commission Notice
Multimedia Projector, Model: WUX500/WUX450ST
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that 
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15...

13
Safety Instructions
Safety InstructionsThis section describes the safety symbols used in this manual. Important projector 
safety information is identified by the following symbols. Always observe the safety 
information by these symbols.
Safety Symbols in this Manual
Denotes the risk of death or serious injury from improper 
handling if the information is not observed. To ensure safe use, 
always observe this information.
Denotes the risk of injury from improper handling if the 
information is not...

Safety Instructions
14
Precautions for Use
As this section contains important safety-related information, be sure to read the 
following carefully beforehand in order to use your projector correctly and safely.
During installation, keep the projector plug easily accessible so that the projector can be 
unplugged immediately if necessary, or keep a circuit breaker within reach.
If the following situations occur, turn the power off, remove the power plug from the 
power outlet and contact the Canon...

15
Safety Instructions
Safety Instructions
Pay attention to the following points regarding the power source, power plug and 
handling of the connector. Failure to do so may cause a fire, electric shock or personal 
injury.
•Do not use any power source with a voltage other than the voltage indicated 
(AC 100–240 V).
•Do not pull the power cord and be sure to hold the power plug or connector 
when removing. Incorrect handling may damage the power cord.
•Do not insert any metal objects into the contact...

Safety Instructions
16
Pay attention to the following points regarding installation and handling of the projector. 
Failure to do so may cause a fire, electric shock or personal injury.
•Do not remove the cabinet from the projector or disassemble it. The interior 
of the projector contains high-voltage components as well as parts that are 
hot. If inspection, maintenance or repair is required, contact the Canon 
Customer Support Center.
•Do not disassemble or modify the projector (including consumable...

17
Safety Instructions
Safety Instructions
Note the following precautions during lamp replacement or when a lamp has ruptured. 
Failure to do so could result in an electric shock or personal injury.
•Before replacing the lamp, always unplug the projector and wait at least an 
hour.
•Ruptured lamps may scatter shards of glass inside the projector. Contact the 
Canon Customer Support Center for cleaning and inspection of the projector 
interior and lamp replacement.
Precautions when replacing lamps that...

Safety Instructions
18
Pay attention to the following points regarding installation and handling of the projector.
•If the projector will not be used for a long period of time, be sure to remove 
the power plug from the power outlet to ensure safety. Failure to do so 
presents a risk of fire if dust accumulates on the plug or outlet.
•Parts of the cabinet around and above the exhaust vents may become hot 
during projection. Touching these areas during operation could cause burns 
to the hands. Pay...

19
For Safe Use
For Safe Use
Pay attention to the following points when carrying or transporting the projector.
•This projector is a precision instrument. Do not knock it over or subject it to 
impacts. Doing so may cause a malfunction.
•Do not reuse any packaging or shock-absorbent materials that were 
supplied with the projector at the time of purchase for transporting or 
shipping the projector. Protection of the projector cannot be guaranteed if 
used packaging or shock-absorbent materials are...

20
Before Installation
Precautions When Carrying/Shipping the 
Projector
Precautions for Installation
Be sure to read “Safety Instructions” and “For Safe Use” (P7 – P19). Also 
take the following precautions during installation.
■Do Not Use in the Following Environments
• Locations with excessive humidity, dust, oily smoke or tobacco smoke
Adhesion to the lens, mirrors or other optical parts may reduce image quality.
• Near high-voltage power lines or sources of electrical power
This may cause...