Canon Projector WUX500 User Manual

181
Product Specifications
Other Information
Product Specifications
*1In full power lamp mode
*2Compliance with ISO21118-2012
* 99.99% or more of the LCD panel pixels are effective. During projection, 0.01% or less of pixels 
may stay lit or unlit due to the characteristics of the LCD panel.
* Using the projector continuously for an extended period of time may accelerate the deterioration of 
optical parts.
* Product specifications and appearance are subject to change without notice.
■Remote Control
Mass...

Product Specifications
182
■External View
Bolt holes (M6 x 4) 
for installation of 
ceiling attachment
WUX500
136 mm 
(5.4)
91.5 mm 
(3.6)
337 mm (13.3)72 mm 
(2.8)362 mm (14.3)
118 mm 
(4.6) 144.5 mm 
(5.7) 144.5 mm 
(5.7)289 mm (11.3)
33 mm (1.3)
301 mm (11.9) 370 mm (14.6)
337 mm (13.3)
Bolt holes (M6 x 4) 
for installation of 
ceiling attachment
WUX450ST
136 mm 
(5.4)
91.5 mm 
(3.6)72 mm 
(2.8)362 mm (14.3)
11 8  m m  
(4.6) 144.5 mm 
(5.7) 144.5 mm 
(5.7)289 mm (11.3)
33 mm (1.3)
301 mm (11.9) 415...

183
Product Specifications
Other Information
Product Specifications
■ANALOG PC-2 / COMPONENT Terminal
This terminal is used as a computer ANALOG PC input or COMPONENT terminal. 
Use a D-sub computer cable.
The terminal specifications for the ANALOG PC input and COMPONENT input are 
the same.
Mini D-sub 15-pin
■Service Port (CONTROL)
Pin assignment
Communication format
Communication mode : RS-232C, asynchronous, half-duplex communication
Communication speed : 19200bps
Character length : 8 bits
Stop bits :...

Product Specifications
184
User commands
Commands ASCII representation Binary representation
Power supplyPower on POWER=ON 50h 4Fh 57h 45h 52h 3Dh 4Fh 4Eh 0Dh
Power off POWER=OFF50h 4Fh 57h 45h 52h 3Dh 4Fh 46h 46h 
0Dh
Power status 
acquisitionGET=POWER47h 45h 54h 3Dh 50h 4Fh 57h 45h 52h 
0Dh
Input sourceHDMI INPUT=HDMI49h 4Eh 50h 55h 54h 3Dh 48h 44h 4Dh 
49h 0Dh
Digital PC INPUT=D-RGB49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h 
47h 42h 0Dh
Analog PC-1 INPUT=A-RGB149h 4Eh 50h 55h 54h 3Dh 41h 2Dh 52h 
47h 42h 31h...

185
Product Specifications
Other Information
Product Specifications
SharpnessSharpness 
value settingSHARP=53h 48h 41h 52h 50h 3Dh  0Dh
Sharpness 
acquisitionGET=SHARP47h 45h 54h 3Dh 53h 48h 41h 52h 50h 
0Dh
ContrastContrast value 
settingCONT=43h 4Fh 4Eh 54h 3Dh  
0Dh
Contrast 
acquisitionGET=CONT 47h 45h 54h 3Dh 43h 4Fh 4Eh 54h 0Dh
AspectAuto ASPECT=AUTO41h 53h 50h 45h 43h 54h 3Dh 41h 55h 
54h 4Fh 0Dh
4:3 ASPECT=4:341h 53h 50h 45h 43h 54h 3Dh 34h 3Ah 
33h 0Dh
16:9 ASPECT=16:941h 53h 50h 45h 43h 54h 3Dh...

186
Troubleshooting
LED Indicator Details
When there is a problem with the projector, the LED indicator on the side of the 
projector illuminates or flashes continuously after the projector is turned off.
• Wait until the cooling fan stops and disconnect the power plug from the electrical outlet before 
dealing with the problem.
LED indicator 
statusMeaning Cause and countermeasure
WARNING and 
TEMP are lit.Temperature 
abnormalityThe temperature inside the projector is too high for 
some reason or the...

187
Troubleshooting
Other Information
Troubleshooting
Symptoms and Solutions
■You Cannot Turn on the Projector
WARNING 
(only) flashes 3 
times 
repeatedly.Filter error The air filter is not installed. Check whether or not 
the air filter is installed correctly. Contact the 
Canon Customer Support Center if the same 
warning occurs again.
Cause Countermeasure
The power cord is not 
connected correctly.Check whether the power cord is connected 
correctly. (P49)
The power cord has just 
been connected.Wait...

Troubleshooting
188
■You Cannot Project an Image from the Projector
Cause Countermeasure
A cable is not connected 
correctly.Check whether the projector is connected to the 
computer or AV equipment correctly. (P46 - P48)
20 seconds have not 
elapsed since the 
projector was turned on.When the projector is turned on, the opening window 
is displayed for approximately 20 seconds. To project 
an image immediately, press the OK button on the 
remote control or side control. (P30, P34)
No image is sent from...

189
Troubleshooting
Other Information
Troubleshooting
■There is no Sound
■The Projected Image Is Blurred
Images on a USB flash 
drive cannot be 
projected.Projection from USB flash drives requires JPEG 
images with a resolution not exceeding 10912x8640, 
single-byte alphanumeric file names, and a FAT-
formatted drive.
The LAN cable (shielded 
twisted pair) is not 
connected correctly.When [LAN] is selected in the [Input] menu, check 
whether the LAN cable (shielded twisted pair) is 
connected to the...

Troubleshooting
190
■You Cannot Project an Image Appropriately
■The Projector Power Turns Off
Video is blurred. Activate motion blur reduction. (P104)
Motion blur reduction is 
not available.Motion blur reduction is not available in projection 
using USB flash drives or networked multi-projection.
The sharpness setting is 
not available.Sharpness cannot be adjusted during split-screen 
display.
Cause Countermeasure
The projected image is 
inverted in the vertical or 
horizontal direction.The ceiling...