Canon Pixma Ip110 User Guide

1.
Roll up the paper in the opposite direction to the paper curl as shown below.
2.
Check that the paper is now flat.
We recommend printing curl-corrected paper one sheet at a time.
Note
•
Depending on the media type, the paper may be smudged or may not be fed properly even if it is not curled inward. In such cases, follow the procedure described below to curl the paper outward within 0.1
inch / 3 mm (B) in height before printing. This may improve the print result.
(C) Printing side
We recommend printing...

Reset the paper thickness lever to the right when you finish printing. If the paper thickness lever is not set back
to the right, the inside of the printer is more likely to get dirty due to the wider clearance between the print head
and the loaded paper. It may also reduce print quality.
Check5  If the intensity is set high, reduce the intensity setting and try printing again.
If you are using plain paper to print images with high intensity, the paper may absorb too much ink and become
wavy, causing...

Back of the Paper Is Smudged
Check1 Did you confirm the paper and print quality settings?
Print Results Not Satisfactory
Check2  Perform the Bottom Plate Cleaning to clean the inside of the printer.
Cleaning the Inside of the Printer (Bottom Plate Cleaning)
Note
•
When performing borderless printing, duplex printing, or too much printing, the inside may become stained
with ink.
453
 

Colors Are Uneven or Streaked
 Colors Are Uneven
 Colors Are Streaked
Check1 Did you confirm the paper and print quality settings?
Print Results Not Satisfactory
Check2 Print the Nozzle Check Pattern and perform any necessary maintenance
operations such as Print Head Cleaning.
Print the Nozzle Check Pattern to determine whether the ink ejects properly from the print head nozzles.Refer to 
When Printing Becomes Faint or Colors Are Incorrect  for the Nozzle Check Pattern printing, Print Head
Cleaning, and...

If Print Head Deep Cleaning does not resolve the problem, the print head may be damaged. Contact the
service center.
Check3  Perform Print Head Alignment.
Aligning the Print Head
Note
•
If the problem is not resolved after performing the Print Head Alignment, perform Print Head Alignment
manually referring to 
Aligning the Print Head Position from Your Computer .
455
 

Ink Is Not Ejected
Check1 Has the ink run out?
Open the print head cover, then check the status of ink lamp.
Checking the Ink Status
Check2  Are the print head nozzles clogged?
Print the Nozzle Check Pattern to determine whether the ink ejects properly from the print head nozzles. Refer to 
When Printing Becomes Faint or Colors Are Incorrect  for the Nozzle Check Pattern printing, Print Head
Cleaning, and Print Head Deep Cleaning.
•
If the Nozzle Check Pattern is not printed correctly:
Check to see if a...

Problems with the Printer
The Printer Cannot Be Powered On
The Printer Turns Off Unintentionally
Cannot Connect to Computer with a USB Cable Properly
Cannot Communicate with the Printer with USB Connection
Print Head Holder Does Not Move to the Position for Replacing
Printer Status Monitor Is Not Displayed
457
 

The Printer Cannot Be Powered On
Check1 Press the  ON button.
Check2
 Make sure that the power plug is securely plugged into the power cord
connector of the printer, then turn it back on.
Check3  Unplug the printer from the power supply, then plug the printer back in and turn
the printer back on after leaving it for at least 2 minutes.
Check4  If you use a battery, check the remaining level of the battery.
For details on how to check it, refer to the battery's instruction manual. If the battery is...

The Printer Turns Off Unintentionally
Check Deactivate the setting to turn the unit off automatically.
The printer turns off automatically according to the elapsed time you specified if you activate the setting to turn
the unit off automatically.
If you do not want the printer to turn off automatically, open the printer driver setup window and in  Auto Power
under the  Maintenance  sheet, select  Disable for Using AC Adapter  in Auto Power Off .
459
 

Cannot Connect to Computer with a USB Cable ProperlyPrinting Speed Is Slow/Hi-Speed USB Connection Does Not Work/"This
device can perform faster" Message Is Displayed
If your system environment is not fully compatible with Hi-Speed USB, the printer will operate at a lower
speed provided under USB 1.1. In this case, the printer operates properly but printing speed may slow
down due to communication speed.
Check  Check the following to make sure that your system environment supports Hi-
Speed USB...