Canon Lbp 5200 User Guide

Installing the Network Board (AXIS 1611)6-16
Optional Accessories
6
4Insert the network board into the expansion slot.
Hold the metal panel portions of the network board and insert the board so that it 
is aligned with the guide rails inside the expansion slot.
IMPORTANT
•Do not touch any of the components, printed wiring, or connectors on the network 
board.
•Push the network board firmly until the printer connector on the network board is 
securely plugged into the connector inside the expansion slot....

Installing the Network Board (AXIS 1611)6-17
Optional Accessories
6
6Connect the LAN cable.
Make sure to use a LAN cable that is compatible with the LAN socket on the 
network board as appropriate for the network you are using.
NOTE
A LAN cable is not supplied with the network board. If you are installing the network 
board to connect the printer to a network, you will need a category 5 twisted pair 
cable. Cables, hubs, etc. should be obtained separately as required.
7Connect the other end of the LAN...

Installing the Network Board (AXIS 1611)6-18
Optional Accessories
6
11Press the power switch to turn the printer on.
IMPORTANT
Refer to the users manual supplied with the AXIS 1611 if the board does not 
operate properly, or an error message appears in the Printer Status Window.
12Check that the Power lamp on the network board is on.
If the network board is not working properly, turn the printer off, and then check 
the LAN cable connection, hub operation, and network board installation.
Power Lamp
 

Installing the Network Board (AXIS 1611)6-19
Optional Accessories
6
Removing the Network Board
Remove the network board using the following procedure. Prepare the protective 
plate for the expansion board slot that you removed when you installed the network 
board.
CAUTION
•Make sure that the printer is turned off and that all interface cables and power 
cord are disconnected from the printer before removing the network board. 
Attempting to remove the board with the power on may result in electrical...

Installing the Network Board (AXIS 1611)6-20
Optional Accessories
6
 

CHAPTER
7-1
7Troubleshooting
This chapter describes the solutions to problems such as a paper jams and poor printing 
quality.
Troubleshooting Map  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Alarm Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Troubleshooting Map7-2
Troubleshooting
7
Troubleshooting Map
If any problem occurs while you are using the printer, follow the flow chart shown 
below to check the source of the problem.
The toner density is set too thin➞Specifying the Print Quality 
(p.4-56)
The toner is running out➞Chapter 5: Replacing Toner 
Cartridges (p.5-7)
The printer is not connected to the computer➞Chapter 1: Connecting to a Computer (p.1-13)
Follow the direction in the 
message displayed in the 
Printer Status Window
➞Chapter 4:...

Alarm Indicator7-3
Troubleshooting
7
Alarm Indicator
If a problem occurs in the printer, the Alarm indicator (red) lights up or blinks.
When the Alarm lamp is on, a service error is occurring. In this case, refer to 
Service Call, on p. 7-28.
If the Alarm lamp is blinking, follow the directions displayed in the Printer Status 
Window.
 

Paper Jams7-4
Troubleshooting
7
Paper Jams
The following messages are displayed in the Printer Status Window when a paper 
jam occurs during printing.
Remove the jammed paper according to the displayed message.
WARNING
There is a high-voltage unit inside this product. When you are clearing paper 
jams or inspecting the interior of the printer, make sure that a necklace, 
bracelet, or other metallic object does not touch the inside of the printer. Doing 
so may cause an electrical shock.
MessageProcedure...

Paper Jams7-5
Troubleshooting
7
CAUTION
•Never touch the electrical contacts or gears inside the top cover. Doing so may 
cause an electrical shock or personal injury.
•Be careful to avoid staining your clothes or hands with toner while you are 
clearing a paper jam. If you get any toner on your hands or clothes, wash it off 
immediately with cold water. Do not rinse with hot water, as this can fix the 
toner, creating a stain that cannot be removed.
•When you are clearing jammed paper from inside the...