Canon Lbp 3300 User Guide

6-26
Optional Accessories
6
Network Board
14Close the expansion slot cover.
Setting the Network Board
The default value of the network board is set at Auto detect. Usually, you do not 
need to change the setting, since the transmission speed and transfer mode of 
10BASE-T/100BASE-TX are detected automatically. If the printer cannot 
communicate with other devices on the network, set the DIP switches on the 
network board. Before setting the DIP switches, turn the printer OFF, then remove 
the network...

6-27
Optional Accessories
6
Network Board
Setting the Network Transmission Speed/Transfer Mode and the DIP 
Switches
1Open the expansion slot cover.
2Turn the printer and computer OFF, remove the USB cable, 
and then disconnect the power plug from the AC power outlet.
3Remove all the interface cables and the power cord from the 
printer.
4Remove the two screws and remove the network board. 
IMPORTANT
Do not touch the network board parts, printed wire, or connectors with your hands.
Communication speed...

6-28
Optional Accessories
6
Network Board
5Set the DIP switches.
Set the DIP switches with the tip of a ball-point pen etc. For details on methods 
for setting the DIP switches, see the table of p. 6-27.
6Insert the network board into the expansion slot.
Hold the metal panel portions of the network board and insert the board while 
aligning it with the guide rails inside the expansion slot.
IMPORTANT
•Do not touch the network board parts, printed wire, or connectors with your hands.
•Insert the printer...

6-29
Optional Accessories
6
Network Board
Problems on Installing the Network Board
On checking the operation of the network board, if you find that all the indicators on 
the network board are off, or the ERR indicator is on or keeps blinking for a long 
time and does not go off, take the following measures.
NOTE
For details on problems on installing the CAPT software, see Chapter 4  
Troubleshooting in Network Guide.
All the indicators on the network board are off.
Cause 1 The LAN cable is not connected...

6-30
Optional Accessories
6
Network Board
The ERR indicator on the network board is on.
Cause The network cable is disconnected or broken, or the network board is not 
installed properly.
Remedy 1 Make sure the network cable is connected properly.
Remedy 2 Replace the network cable with a proper one and check if there is no 
disconnection or damage.
Remedy 3 If the ERR indicator still comes on even after applying the Remedy 1 and 2, 
contact your local authorized Canon dealer for servicing.
The ERR...

6-31
Optional Accessories
6
Network Board
1Open the expansion slot cover.
2Turn the printer and computer OFF, remove the USB cable, 
and then disconnect the power plug from the AC power outlet.
3Remove all the interface cables and the power cord from the 
printer.
4Remove the two screws and remove the network board.
IMPORTANT
Do not touch the network board parts, printed wire, or connectors with your hands.
5Switch the DIP switch 1 to ON.
Set the DIP switches with the tip of a ball-point pen etc....

6-32
Optional Accessories
6
Network Board•
Insert the printer connector of the network board securely into the connector inside 
the expansion slot.
7Secure the top and bottom portions of the network board with 
the two screws supplied with the network board.
8Connect the power cord.
9Plug the power plug into the AC power outlet.
10Press   of the power switch to turn the printer ON, wait until 
the   (Ready) indicator comes on, and then press   of the 
power switch to turn the printer OFF.
11Disconnect...

6-33
Optional Accessories
6
Network Board
14Install the network board.
15Connect the interface cables except for the USB cable, and 
connect the power cord.
16Plug the power plug into the AC power outlet.
17Connect the USB cable as needed, then close the expansion 
slot cover.
 
Removing the Network Board
Remove the network board using the following procedure. Have ready the 
protective plate and screws for the expansion slot removed when the network board 
was installed.
CAUTION
•Be sure to turn the...

6-34
Optional Accessories
6
Network Board
IMPORTANT
•Do not touch the network board parts, printed wire, or connectors with your hands.
•The removed two screws are required when the network board is installed. Keep 
them where they will not get lost.
5Attach the protective plate to the expansion slot and secure it 
with the screws.
6Connect the interface cables except for the USB cable, and 
connect the power cord.
7Plug the power plug into the AC power outlet.
8Connect the USB cable, then close the...

CHAPTER
7-1
7Troubleshooting
This chapter describes the remedies for problems such as a paper jam or poor print quality.
Troubleshooting Map  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Alarm Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....