Canon Laser Shot Lbp5970 User Guide

60
Step8 Raise the slot cover a little 
b, then remove the slot cover in the direction of the 
arrow c.
IMPORTANT
•Do not touch the main board parts, printed wire, or connectors with your 
hands.
•When installing RAM/ROM, be careful so that any metal objects such as 
screws do not touch the main board.
•Do not drop screws, paper clips, staples, or other metal objects inside the 
printer. If any of these objects should drop inside the printer, do not plug 
the power plug into the AC power outlet and...

61
Step8
Align the notch (B) with the RAM slot as shown in the figure 
a, and then insert 
the RAM module completely into the slot b.
When the RAM module is installed properly, it is locked by the levers (B) on both 
sides of the RAM slot.
● Installing ROM
Open up the lever of the ROM slot.
Insert the ROM module into the slot guides so that its notch (A) is at the \
opposite 
side of the lever (B), and then press the ROM module completely into the slot.
When the ROM module is installed properly, the...

62
Step8
9Attach the rear cover  a, then slide it  b as shown in the 
figures.
10Connect the interface cables except for the USB cable, and 
connect the power cord.
11Plug the power plug into the AC power outlet.
12Connect the USB cable.
NOTE
After installing the RAM, you have to specify the settings for the optional 
accessories in the [Device Settings] sheet in the printer driver. You can 
obtain the status of the optional accessories automatically by clicking [Get 
Device Status] in the [Device...

63
Step8
-D
o not touch the hard disk parts, printed wire, or connectors with your 
hands.
-T o prevent the hard disk from being affected by static electricity, keep it in 
the protective bag until it is ready to be installed. Also, keep the hard disk 
aw ay from products that generate strong magnetic waves.
•Do not drop or jolt the hard disk.
•Because the hard disk is a precision device, do not press on the top of its 
drive, place it over another, or hit it against other objects.
•Be sure not to remove...

64
Step8
4Insert the hard disk into the hard disk slot.
Hold the metal panel portion of the hard disk and insert the disk while aligning it 
with the guide rails inside the hard disk slot.
IMPORTANT
•Insert the hard disk securely.
•Do not touch the hard disk parts, printed wire, or connectors with your 
hands.
5Secure the top and bottom portions of the hard disk with 
the two screws supplied with the hard disk.
6Attach Shut Down label supplied with the hard disk to a 
conspicuous part on the printer....

65
Step8
11Press [Settings].
12Select INITIALIZE MENU using [ ] and [ ], then 
press [OK].
A confirmation message is displayed.
13Press [OK].
IMPORTANT
If the message  appears when the initialization of the 
SETUP menu is executed, the SETUP menu is not initialized.
14After completing the initialization, perform a hard reset or 
cy cle the power of the printer.
After starting the printer, the hard disk is formatted.
While the hard disk is being formatted,  is displayed in the display. 
Wa it for a moment...

FT5-2311   (010) XXXXXXXXXX©2009 CANON INC. PRINTED IN JAPAN
CANON INC.30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON MARKETING JAPAN INC.16-6, Konan 2-chome, Minato-ku, Tokyo 108-8011, Japan
CANON U.S.A., INC.One Canon Plaza, Lake Success, NY 11042, U.S.A.
CANON EUROPA N.V.Bovenkerkerweg, 59-61, 1185 XB Amstelveen, The Netherlands
CANON CHINA CO. LTD.15F Jinbao Building No.89, Jinbao Street, Dongcheng District, Beijing 10\
0005, PRC
CANON SINGAPORE PTE LTD1 HarbourFront Avenue, #04-01...