Canon Laser Shot Lbp5970 User Guide

							60
Step8 Raise the slot cover a little 
b, then remove the slot cover in the direction of the 
arrow c.
IMPORTANT
•Do not touch the main board parts, printed wire, or connectors with your 
hands.
•When installing RAM/ROM, be careful so that any metal objects such as 
screws do not touch the main board.
•Do not drop screws, paper clips, staples, or other metal objects inside the 
printer. If any of these objects should drop inside the printer, do not plug 
the power plug into the AC power outlet and contact your local authorized 
Canon dealer.
•Do not turn the printer ON without the rear cover or slot cover attached. 
This may result in damage to the printer.
NOTE
The positions where the RAM/ROM modules are to be installed are as 
shown in the following figure. Confirm the mounting locations before 
installing the RAM/ROM modules.
6Install RAM/ROM.
● Installing RAM
Open up the levers (A) of the RAM slot.
c
b
RAM slot 
ROM slot
(A
)
 
						

							61
Step8
Align the notch (B) with the RAM slot as shown in the figure 
a, and then insert 
the RAM module completely into the slot b.
When the RAM module is installed properly, it is locked by the levers (B) on both 
sides of the RAM slot.
● Installing ROM
Open up the lever of the ROM slot.
Insert the ROM module into the slot guides so that its notch (A) is at the \
opposite 
side of the lever (B), and then press the ROM module completely into the slot.
When the ROM module is installed properly, the projection of the lever is caught in 
the notch (C) of the ROM.
CAUTION
Be careful not to be injured by the edges of the main board parts or 
the RAM/ROM modules.
7Attach the slot cover  a, then close it  b.
8Secure the slot cover using the six screws.
(A
)
(A)
(B)
a
b
(B)
(C)(A)
a
b
 
						

							62
Step8
9Attach the rear cover  a, then slide it  b as shown in the 
figures.
10Connect the interface cables except for the USB cable, and 
connect the power cord.
11Plug the power plug into the AC power outlet.
12Connect the USB cable.
NOTE
After installing the RAM, you have to specify the settings for the optional 
accessories in the [Device Settings] sheet in the printer driver. You can 
obtain the status of the optional accessories automatically by clicking [Get 
Device Status] in the [Device Settings] sheet.
If you cannot obtain the status of the optional accessories of the printer 
automatically, select the installed optional accessories from [Installed 
Memory].
Installing a Hard Disk
A hard disk is to be installed in the hard disk slot of the printer unit. Make sure 
that all the following items are contained in the package before installing a 
hard disk. If any item is missing or damaged, please contact your local 
authorized Canon dealer.
A Phillips screwdriver is required for installing a hard disk. Have a screwdriver 
ready in advance that matches the size of the screws.
Observe the following guidelines when installing the hard disk.
CAUTION
•Be sure to turn the printer OFF, and then disconnect all the interface 
cables and power cord from the printer before installing the hard 
disk. Failure to observe these steps may result in an electrical shock.
•Be careful when handling a hard disk. Touching the edges or a sharp 
portion of a hard disk may result in personal injury.
IMPORTANT
•The hard disk contains components that are sensitive to static electricity. 
Observe the following precautions when handling them to prevent damage 
from static electricity.
-Touch a metal object to dissipate static electricity before handling them.
-W hen handling them, do not touch anything that generates static 
electricity such as the computer display.
a
b
Hard Disk
Guide sheet
Shut Down label Screws 
(2 pieces)
Encrypted Secured Print Driver  Add-in For Client PC
 
						

							63
Step8
-D
o not touch the hard disk parts, printed wire, or connectors with your 
hands.
-T o prevent the hard disk from being affected by static electricity, keep it in 
the protective bag until it is ready to be installed. Also, keep the hard disk 
aw ay from products that generate strong magnetic waves.
•Do not drop or jolt the hard disk.
•Because the hard disk is a precision device, do not press on the top of its 
drive, place it over another, or hit it against other objects.
•Be sure not to remove any label or others attached to the top of the drive 
of the hard disk. Also, do not attach any other labels.
•Do not move the hard disk suddenly from a cool location to a hot location.
•After installing the hard disk, you need to initialize the SETUP menu. 
Therefore, if you have changed the printer setting, output the Configuration 
Page Print and confirm and save the status of the printer setting before 
installing the hard disk. For details on the procedure for outputting 
Configuration Page Print, see Checking the Operations with Configuration 
P age Print, on p. 42.
1Turn the printer and computer OFF  a, remove the USB 
cable  b, and then disconnect the power plug from the AC 
power outlet  c.
2Remove all the interface cables and the power cord from 
the printer.
If there is not sufficient space to install the hard disk, move the printer to a place 
where you can work easier.
3Remove the screws and remove the protective plate for the 
hard disk.
IMPORTANT
•The removed protective plate and screws are required when the hard disk 
is removed. Be sure not to misplace them.
•After removing the protective plate, be careful not to drop screws, paper 
clips, staples, or other metal objects inside the hard disk slot. If any of 
these objects should drop inside the hard disk slot, do not plug the power 
plug into the AC power outlet and contact your local authorized Canon 
dealer.
a
a
b
c
 
						

							64
Step8
4Insert the hard disk into the hard disk slot.
Hold the metal panel portion of the hard disk and insert the disk while aligning it 
with the guide rails inside the hard disk slot.
IMPORTANT
•Insert the hard disk securely.
•Do not touch the hard disk parts, printed wire, or connectors with your 
hands.
5Secure the top and bottom portions of the hard disk with 
the two screws supplied with the hard disk.
6Attach Shut Down label supplied with the hard disk to a 
conspicuous part on the printer.
IMPORTANT
When you turn the printer OFF after installing the hard disk, execute SHUT 
DOWN following the directions in the label in order to protect the hard disk, 
and then press    of the power switch.
7Connect the power cord.
8Plug the power plug into the AC power outlet.
9Press     of the power switch to turn the printer ON.
10Initialize the SETUP menu using the following procedure.
IMPORTANT
Initialize the SETUP menu after installing the hard disk. The functions of 
the hard disk are formatted and become effective by initializing the SETUP 
menu.
* Sample of the labeling position
 
						

							65
Step8
11Press [Settings].
12Select INITIALIZE MENU using [ ] and [ ], then 
press [OK].
A confirmation message is displayed.
13Press [OK].
IMPORTANT
If the message  appears when the initialization of the 
SETUP menu is executed, the SETUP menu is not initialized.
14After completing the initialization, perform a hard reset or 
cy cle the power of the printer.
After starting the printer, the hard disk is formatted.
While the hard disk is being formatted,  is displayed in the display. 
Wa it for a moment until the format is completed.
After the format of the hard disk is completed, connect all the interface cables.
IMPORTANT
The hard disk is formatted automatically after you install the hard disk, 
initialize the SETUP menu, and start the printer. If the format is not 
performed at this point, perform QUICK FORMAT in HDD MAINTENANCE 
in the SETUP menu. For more details, see Chapter 5 Printing 
Environment Settings in
  Users Guide.
NOTE
After installing the hard disk, you have to specify the settings for the 
optional accessories in the [Device Settings] sheet in the printer driver. You 
can obtain the status of the optional accessories automatically by clicking 
[Get Device Status] in the [Device Settings] sheet.
If you cannot obtain the status of the optional accessories automatically, 
select the [Hard Disk Installed] check box.
Settings
SETUP
CONTROL MENU   →
OK
Settings
Utility
OK?
INITIALIZE MENU→
OK
DONE
INITIALIZING
CD-ROM
 
						

							FT5-2311   (010) XXXXXXXXXX©2009 CANON INC. PRINTED IN JAPAN
CANON INC.30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON MARKETING JAPAN INC.16-6, Konan 2-chome, Minato-ku, Tokyo 108-8011, Japan
CANON U.S.A., INC.One Canon Plaza, Lake Success, NY 11042, U.S.A.
CANON EUROPA N.V.Bovenkerkerweg, 59-61, 1185 XB Amstelveen, The Netherlands
CANON CHINA CO. LTD.15F Jinbao Building No.89, Jinbao Street, Dongcheng District, Beijing 10\
0005, PRC
CANON SINGAPORE PTE LTD1 HarbourFront Avenue, #04-01 Keppel Bay Tower, Singapore 098632
CANON AUSTRALIA PTY LTD1 Thomas Holt Drive, North Ryde, Sydney NSW 2113, Australia
CANON GLOBAL WORLDWIDE SITEShttp://www.canon.com/