Canon Laser Shot Lbp5970 User Guide

							50
Step8
Installation Space
The dimensions of each part, foot positions, and the space required for using 
the printer with the paper feeders installed are indicated in the following 
figures:
Moving the Printer
When installing the paper feeder in the printer after installing the printer, 
move the printer to an appropriate location temporarily using the following 
procedure.
W ARNING
Be sure to turn the printer and computer OFF, unplug the power plug, 
and then disconnect all the interface cables from the printer before 
moving the printer. Otherwise, the power cord or interface cables 
may be damaged, resulting in a fire or electrical shock.
CAUTION
Do not carry the printer with the paper cassette attached. If you do 
so, the paper cassette may drop resulting in personal injury.
1Turn the printer and computer OFF  a, remove the USB 
cable  b, and then disconnect the power plug from the AC 
power outlet  c.
2Remove all the interface cables and the power cord from 
the printer.
• Dimensions of the PrinterFront Surface
Paper cassette
Cassette protective cover
545
798
656.5
517
691.5 651 46 (mm)
(mm)
• Required Peripheral Space
Front Surface
Paper 
cassette
Cassette 
protective cover
1656
795
210
745
100
100
917
1056.5
1198
100T op coverF ront cover
• Foot Positions of the Paper Feeder
The rubber feet are 5 mm high and their top surface is 18 mm in diameter\
.(mm)
Front Surface63 442 192
63 442 192
428.5 78.8
37.7 430 77.5
35.5
a
a
b
c
 
						

							51
Step8
3Pull out the paper cassette.
Pull the paper cassette out until it stops a.
After lifting the paper cassette up a little 
b, pull it out while supporting it with the 
other hand in the figure c.
IMPORTANT
The paper cassette cannot be pulled out horizontally. If you try to pull it out 
f orcefully, this may result in damage to the paper cassette.
4Move the printer unit from the installation site.
Carry the printer with 4 or more people by holding the lift handles on the lower 
portion of the printer and lifting it up at the same time.
CAUTION
•The printer weight is approximately 55.7 kg without the paper 
cassette installed. The printer must be carried by 4 or more people, 
and care must be taken to avoid hurting your back or other portions 
of your body when carrying the printer.
a
b
c
 
						

							52
Step8
•Be sure not to hold the printer by the paper cassette, output area, or 
any portions other than the lift handles. If you do so, you may drop 
the printer, resulting in personal injury.
IMPORTANT
Make sure that the front cover and multi-purpose tray are closed before 
carrying the printer.
Installing the Paper Feeders
The paper feeders are to be installed at the bottom of the printer unit.
CAUTION
•Put the printer or paper feeders down slowly and carefully. Be careful 
not to hurt your hands.
•Do not carry the printer with the paper cassettes attached. If you do 
so, the paper cassettes may drop resulting in personal injury.
•Do not carry the printer with the paper feeders installed. If you do so, 
the paper feeders may drop resulting in personal injury.
IMPORTANT
•If the paper feeders are installed, make sure that the paper cassette of the  
paper feeder (Cassette 2, Cassette 3, or Cassette 4) to feed and paper 
cassettes upper than the feeding paper feeder are set before using the 
printer. If those paper cassettes are not set, paper cannot be fed from the 
lower paper source. (For example, if Cassette 2 is not set, paper cannot be 
fed from Cassette 3.)
•If there is any packing material remaining inside the paper feeder, this may 
result in misfeeds or damage to the printer when operating the printer. Be 
sure to remove all the packing materials following the procedure.
•The removed packing materials are required when transporting the printer 
for relocation or maintenance. Keep them where they will not get lost.
NOTE
The packing materials may be changed in form or position to be placed, or 
may be added or removed without notice.
 
						

							53
Step8
1Remove the tape that secures the paper cassette and 
cassette protective cover.
2Remove the packing materials shown in the figure in order 
of  a and  b. IMPORTANT
Dispose of the packing materials according to local regulations.
3Pull out the paper cassette.
Pull the paper cassette out until it stops a.
After lifting the front of the paper cassette up a little 
b, pull it out while supporting 
the cassette with your left hand until the handle (A) on the right sid\
e of the paper 
cassette appears completely 
c.
a
a
b
a
(A)
c
b
 
						

							54
Step8 While holding the paper cassette with both hands, pull it out completely\
 
d as 
shown in the figure.
IMPORTANT
•Because the paper cassette is heavy, hold it with your both hands 
securely.
•Place the removed paper cassette on an even and stable surface.
•The paper cassette cannot be pulled out horizontally. If you try to pull it out 
f orcefully, this may result in damage to the paper cassette.
4Remove the packing material attached with tape.
5Remove the tape and packing material attached to the 
paper cassette.
*D epending on the paper feeder you purchased, the tape f may not be attached.
IMPORTANT
•Packing materials are attached to the paper cassette. Be sure to pull out 
the paper cassette and remove all the packing materials.
d
b
a
c
d
f *e
g
h
i
 
						

							55
Step8
•Do not touch the feed roller (A) in the paper cassette. This may result in 
misfeeds.
•Dispose of the packing materials according to local regulations.
6Remove the cassette protective cover of the paper feeder.
While pressing the levers of the cassette protective cover, remove the cassette 
protective cover as shown in the figure.
7Place the paper feeder at the installation site.
When carrying the paper feeder, hold the lift handles on both sides with both 
hands as shown in the figure.
CAUTION
The weight of the printers is as follows.
Be sure to install the printer on a sturdy platform that can easily 
support the weight of the printer and optional accessories. Do not 
install the printer in unstable locations, such as unsteady platforms 
or inclined floors, in locations subject to excessive vibrations, or on 
the upper row of a computer rack, as this may cause the printer to fall 
or tip over, resulting in personal injury.
(A)
DefaultWith the toner 
cartridges and drum  cartridges installedWith the optional paper  feeders (3 units) 
installed
Approx. 48.5 kg Approx. 57.4 kg Approx. 90.4 kg
 
						

							56
Step8
IMPORTANT
•Do not touch the connector (A) or feed rollers (B) in the paper feeder. This 
may result in damage to the printer or misfeeds.
•Do not install the paper feeder on a platform that may warp from the 
weight of the printer and optional accessories, or where the printer is liable 
to sink (such as a carpet or mat).
•Secure sufficient space around the paper feeder so that you can install the 
printer and connect cords such as the power cord and interface cables.
8When installing a paper feeder on another paper feeder, 
match the positioning pins (A) and gently set it down.
When installing only one paper feeder, proceed to Step 10.
NOTE
Up to 3 paper feeders can be installed.
9Fix the paper feeder using the four supplied screws.
Tighten the screws firmly.(B)
(A)
(A) (A)
- Front side
- Rear side
 
						

							57
Step8
10Gently set down the printer unit while matching the 
positioning pins (A) on the paper feeder.
11Fix the printer unit and paper feeder with the two metal 
fittings and two screws.
Hook the holes (A) of the metal fittings onto the hooks (B) on the\
 printer a, and 
then secure them with the screws b. Hook the tabs (A) of the metal fittings in the holes (B) on the pr\
inter 
c, and then 
secure them with the screws d.
(A)(A)
(A)
a
b
(A)
a
b
(B)
c
d
(A)
(B)
c
d
(A)
(B)
- Left side
- Right side
 
						

							58
Step8
12Attach the cassette protective cover.
While pressing the levers of the cassette protective cover, insert the projections 
into the slot on the rear side of the paper feeder.
IMPORTANT
Do not put your hand or any object on the cassette protective cover, nor 
press it forcefully. This may result in damage to the cassette protective 
cover.
13Set the paper cassette in the printer unit and paper feeder.
14Connect the interface cables except for the USB cable, and 
connect the power cord.
15Plug the power plug into the AC power outlet.
16Connect the USB cable. NOTE
After installing the paper feeder, you have to specify the settings for the 
optional accessories in the [Device Settings] sheet in the printer driver. You 
can obtain the status of the optional accessories automatically by clicking 
[Get Device Status] in the [Device Settings] sheet.
If you cannot obtain the status of the optional accessories of the printer 
automatically, select the installed optional accessories from [Paper Source 
Options].
Installing RAM/ROM
Expansion RAM/ROM modules are to be installed on the main board at the 
rear side of the printer. A Phillips screwdriver is required for installing a RAM/
R
OM module. Have a screwdriver ready in advance that matches the size of 
the screws. Observe the following guidelines when installing RAM or ROM.
CAUTION
•Be sure to turn the printer OFF, and then disconnect all the interface 
cables and power cord from the printer before installing RAM/ROM. If 
y ou attempt to install RAM/ROM when the printer is ON or any cable 
is connected to the printer, this may result in an electrical shock.
•Be careful when handling a RAM/ROM module. Touching the edges 
or a sharp portion of a RAM/ROM module may result in personal 
injury.
IMPORTANT
•RAM/ROM modules contain components that are sensitive to static 
electricity. Observe the following precautions when handling a RAM/ROM 
module to prevent damage from static electricity.
-T ouch a metal object to dissipate static electricity before handling a 
RAM/ROM module.
-W hen handling a RAM/ROM module, do not touch anything that 
generates static electricity such as the computer display.
-D o not touch the main board parts, printed wire, or connectors with your 
hands.
-T o prevent the RAM/ROM module from being affected by static 
electricity, keep it in the protective bag until it is ready to be installed.
•Be sure not to touch the switches on the main board. If you change the 
sw itches, the printer does not operate properly.
 
						

							59
Step8
1Turn the printer and computer OFF  a, remove the USB 
cable  b, and then disconnect the power plug from the AC 
power outlet  c.
2Remove all the interface cables and the power cord from 
the printer.
If there is not sufficient space to install the RAM/ROM module, move the printer to 
a place where you can work easier.
3Remove the rear cover.
Slide the opening (A) on the rear cover a little in the direction of the arrow a. Open the rear cover a little 
b, then remove the rear cover in the direction of the 
arrow c.
4Remove the six screws of the slot cover.
5Remove the slot cover.
Open the slot cover a.
a
a
b
c
(A)
a
b
c
a