Canon Ir 1600 User Guide

1-23Placing Originals
Before You Start Using This Machine
1
Placing Originals
Set the originals on the platen glass or in the feeder, depending on the size and type of paper that 
you want to print and the settings that you have programmed.
■Platen glass
Place the originals on the platen glass when scanning bound originals, originals on heavy or 
lightweight paper, and transparencies.
■Feeder (when attached)
Place a stack of originals in the optional feeder, and press   (Start). The machine automatically...

Before You Start Using This Machine
1
1-24Placing Originals
Orientation of Originals
You can place original either vertically or horizontally. Always align the top edge of your original 
with the back edge of the platen glass (upper left corner) or the feeder.
Staple copy: place the original with its top upward
IMPORTANT
•The copies are stapled at the part equivalent to the upper left side of the original.
NOTE
•If the top edge of the original is not aligned with the back edge of the platen glass, prints...

1-25Placing Originals
Before You Start Using This Machine
1
Placing an Original on the Platen Glass
You should use the platen glass when scanning books and other bound originals, heavy or 
lightweight paper originals, transparencies, etc., into memory.
IMPORTANT
•When the optional feeder is attached, the original-size-detection function of the platen glass does not work.
1Lift up the feeder/platen glass cover.
IMPORTANT
•The iR2000 is equipped with an open/close sensor of the platen glass cover. When...

Before You Start Using This Machine
1
1-26Placing Originals
2Place your original.
The surface that you want to scan into memory must be placed face down. Align the corner of the original 
with the top left corner (the arrow) of the platen glass.
Place books and other bound originals on the platen glass in the same way.
When enlarging A4, B5 or A5-size originals to A3 or B4-size paper, place the original horizontally on the 
platen glass, and align it with the A4  , B5   or A5   marks.
 

1-27Placing Originals
Before You Start Using This Machine
1
3Gently lower the feeder/platen glass cover.
CAUTION
•Close the feeder/platen glass cover gently, to avoid catching your hand, as this may result in personal injury.
•Do not press down the feeder/platen glass cover with force when scanning thick books. This may damage the 
platen glass and cause personal injury.
IMPORTANT
•When placing originals on the platen glass, the size of the original is detected after the platen glass cover has been...

Before You Start Using This Machine
1
1-28Placing Originals
Placing Originals in the Optional Feeder (ADF-J1)
If the machine is equipped with the optional feeder, place a stack of originals, and press   (Start). 
The machine automatically scans them into memory.
You can place the following originals in the original supply tray:
•Weight:  38 to 128 g/m
2 (set the originals one-by-one when they are very thin
(38 to 52 g/m2) or very thick (105 to 128 g/m2))
•Size: A3  , B4  , A4  , A4  , B5  , B5  , A5  ,...

1-29Placing Originals
Before You Start Using This Machine
1
2Adjust the slide guides to fit the size of the originals.
IMPORTANT
•Do not add or remove originals while they are being scanned.•When scanning is completed, remove the originals from the original output tray to avoid paper jams.
NOTE
•The scanned originals are output face down to the original output tray.
Original output tray
 

1-30Making Prints Using the Stack Bypass
Before You Start Using This Machine
1
Making Prints Using the Stack Bypass
When making prints on transparencies, or non-standard size paper stock, load the paper stock in 
the stack bypass.
IMPORTANT
•Note the following points when using the stack bypass:
- Copy quantity: 1 to about 100 sheets (80 g/m2)
- Paper size: 100 mm x 148 mm to 297 mm x 432 mm
- Paper weight: 60 g/m
2 to 128 g/m2
- Curl down paper before use. (Curl amount: less than 10 mm for normal paper;...

1-31Making Prints Using the Stack Bypass
Before You Start Using This Machine
1
1Open the stack bypass.
●If the specified paper has already been loaded in the stack bypass:
▼Press   (Paper Select) repeatedly until the indicator for the stack bypass lights.
●If paper different from that specified is loaded in the stack bypass:
▼Check to see if any job is reserved. (See “Flow of Checking/Canceling Operations,” on
p. 2-2.)
▼When there is no reserved job, continue the procedure from step 2.
2Adjust the slide...

Before You Start Using This Machine
1
1-32Making Prints Using the Stack BypassWhen feeding large-size paper, pull out the auxiliary tray.
3Press   (Paper Select) repeatedly until the indicator for the stack bypass lights up on 
the control panel.
4Load the paper in the stack bypass with the side to be printed on facing down.
Make sure that the height of the paper stack does not exceed the limit mark.
Align the required number of sheets of paper with the slide guides. Insert the paper into the machine...