Brother Quattro 3 User Manual
Have a look at the manual Brother Quattro 3 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 331 Brother manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS 19 6162 6364 **In some countries or regions, this is not included in the enclosed accessories. No. Part Name Part Code Americas Others 1 Zigzag foot “J” (on machine) XC3021-051 2 Monogramming foot “N” X53840-351 3 Overcasting foot “G” XC3098-051 4 Zipper foot “I” X59370-051 5 Buttonhole foot “A” X57789-251 6 Blind stitch foot “R” X56409-051 7 Button fitting foot “M” 130489-001 8 Walking foot SA140 F033N: XC2214-052 9 Side cutter foot SA177 F054: XC3879-152 10 Straight stitch foot SA167 F042N: XC1973-052 11 Free motion quilting foot “C” XE0765-101 12 Free motion echo quilting foot “E” XE0766-001 13 Free motion open toe quilting foot “O” SA187 F061: XE1097-001 14 Embroidery foot “W2” with LED pointer XF6319-001 15 Vertical stitch alignment foot “V” SA189 F063: XE5224-001 16 Needle set XE4962-001 17 Twin needle XE4963-001 18 Ball point needle set XD0705-051 19 Bobbin × 10 (One is on machine.) SA156 SFB: XA5539-151 20 Seam ripper XF4967-001 21 Scissors XC1807-121 22 Cleaning brush X59476-051 23 Eyelet punch XZ5051-001 24 Screwdriver (small) X55468-051 25 Screwdriver (large) XC4237-021 26 Disc-shaped screwdriver XC1074-051 27 Spool cap (small) 130013-154 28 Spool cap (medium) × 2 (One is on machine.) X55260-153 29 Spool cap (large) 130012-054 30 Spool cap (special) XA5752-121 31 Spool stand See page 21 32 Bobbin clip × 10 XE3060-001 33 Spool felt X57045-051 34 Spool net × 2 XA5523-050 35 Embroidery needle plate cover XE5131-001 36 Touch pen (stylus) XA9940-051 37 Knee lifter SA599 KL1: XE5902-001 38 USB cable XD0745-051 39 Alternate bobbin case (no color on the screw) XC8167-551 40 Bobbin case (gray, for bobbin work) XE8298-001 41 Straight stitch needle plate XE4908-301 42 Cord guide bobbin cover (with single hole) XE8991-101 43 Bobbin cover (with mark) XF0750-101 44 Multi-function foot controller See Operation Manual Addendum 45 Embroidery frame set (small) H 2 cm × W 6 cm (H 1 inch × W 2-1/2 inches) SA437 EF73: XC8479-152 46 Embroidery frame set (medium) H 10 cm × W 10 cm (H 4 inches × W 4 inches) SA438 EF74: XC8480-152 47 Embroidery frame set (quilt) H 20 cm × W 20 cm (H 8 inches × W 8 inches) SA446 EF91: XE5068-101 48 Embroidery frame set (extra large) H 30 cm × W 20 cm (H 12 inches × W 8 inches) SA447 EF92: XE5071-001 49 Embroidery bobbin thread SA-EBT XC6283-001 50 Embroidery positioning sticker sheets SAEPS2 EPS2: XF0763-001 51 Edge sewing sheet × 6 SAESS1 ESS1: XE5094-001 52 Stabilizer material SA519 BM3: XE0806-001 53 Grid sheet set SA507 GS3: X81277-151 54 Chalk pencil XE8568-001 55 USB mouse XE5334-101 56 Pen tablet See page 23 57 LCD cleaning cloth XE4913-001 58 Soft cover XE5111-001 59 Embroidery unit carrying case XE3791-001 60 Accessory case XF7275-001 61 Operation manual This manual 62 Operation manual addendum XF6300-001 63 Quick reference guide XF6299-001 64 My Custom Design CD XF6585-001 Memo Foot controller: Model V This foot controller can be used on the machine with product code 882-W07. The product code is mentioned on the machine rating plate. Memo Always use accessories recommended for this machine. The screw for the presser foot holder is available through your authorized dealer (Part code XA4813-051). Included accessories 38, 44, 61 and 62 can be stored in the machine’s soft cover case. (In some countries or regions, the soft cover case is not included in the enclosed accessories.) No. Part Name Par t C ode Americas Others
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS 20 Options The following are available as optional accessories to be purchased separately from your authorized Brother dealer. 12 3 45 6 78 9 10 11 12 13 14 15 16 No. Part NamePart Code Americas Others 1 Border embroidery frame H 30 cm × W 10 cm (H 12 inches × W 4 inches) with Kit 3 upgrade SABF6000D2 NV1UGK3 2 Border embroidery frame set H 18 cm × W 10 cm (H 7 inches × W 4 inches) SABF6000D BF2: XE5059-001 3 10 spool stand SA560 TS4: XE5065-101 4 Wide table and free motion grip SATFM6000DTFM-3: XE5062-001 5 Embroidery frame set (large) H 18 cm × W 13 cm (H 7 inches × W 5 inches) SA439 EF75: XC8481-152 6 Embroidery card reader SAECRI 7 Embroidery card – 8 Stabilizer material SA519 BM3: XE0806-001 Water soluble stabilizer SA520 BM5: XE0615-001 9 1/4 quilting foot with guide SA185 F057: XC7416-252 10 Embroidery bobbin thread (white) SAEBT EBT-CEN: X81164-001 Embroidery bobbin thread (black) SAEBT999 EBT-CEBN: XC5520-001 11 Seam guide SA538 SG1: XC8483-052 12 Embroidery positioning sticker sheets SAEPS2 EPS2: XF0763-001 13 Edge sewing sheet × 5 SAESS1 ESS1: XE5094-001 14 Protective sheet SAPS6000D PS1: XF2653001 15 Square embroidery frame H 15 cm x W 15 cm (H 6 inches x W 6 inches) SA448 (U.S.A.) SA448C (Canada) SEF150: XF4163-001 16 Embroidery foot “W” XC8156-651 Memo All specifications are correct at the time of printing. Please be aware that some specifications may change without notice. Note Embroidery cards purchased in foreign countries may not work with your machine. Visit your nearest authorized Brother dealer for a complete listing of optional accessories and embroidery cards available for your machine. No. Part Name Part Code Americas Others
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS 21 Using the Spool Stand The included spool stand is useful when using thread spools with a large diameter (cross-wound thread). The spool stand can hold two spools of thread. ■How to assemble the spool stand aFully extend the telescopic thread guide shaft, and then rotate the shaft until the two internal stoppers click into place. bInsert the telescopic thread guide into the round hole at the center of the spool support, and then use a screwdriver to securely tighten the screw ( a) from the reverse side. a Screw 12 3 45 6 78 9 No. Part Name Part Code 1 Telescopic thread guide XE0776-001 2 Spool support XE4637-001 3 Spool pin × 2 XA6313-051 4 Screw and washer XC7568-051 5 Spool cap (XL) × 2 XE0779-001 6 Spool holder × 2 XA0679-050 7 Spool cap base × 2 XE0780-001 8 Spool felt × 2 XC7134-051 9 Ring × 4 026030-136 CAUTION Do not lift the handle of the machine while the spool stand is installed. Do not push or pull the telescopic thread guide or spool pins with extreme force, otherwise damage may result. Do not place any object other than spools of thread on the spool support. Do not try to wind thread on the bobbin while sewing using the spool stand. Note Make sure that the stoppers on the tele-scopic thread guide shaft are firmly in place and that the top of the thread guide is directly above the spool pins. In addition, check that the shaft is securely tightened in the spool support.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS 22 cFirmly insert the two spool pins into the two holes in the spool support. dOpen the upper cover of the machine. From the back of the machine, press in the upper cover latches (one on each side), and then pull the upper cover up to remove it from the machine. eInsert the spool stand onto the notches of the machine. ■How to remove aFrom the back of the machine, press in the spool stand latches (one on each side), and then pull the spool stand up to remove it from the machine. bAttach the upper cover to the machine. Memo See page 52 about the bobbin winding using the spool stand. See page 63 about the upper threading using the spool stand.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS 23 Using the Pen Tablet ■Installing a battery in the tablet pen A battery for the tablet pen is not included with your machine. Use a new AAA alkaline battery (LR03). aUnscrew the upper barrel of the tablet pen. bInstall a new AAA alkaline battery (LR03) in the tablet pen with the positive end (+) pointing up. cScrew the upper barrel to the tablet pen. ■Replacing the pen tip When the pen tip is worn out, replace with a new one included with your pen tablet. aGrasp the old pen tip firmly with the included pen tip clip. Memo See page 34 about connecting the pen tab- let with the sewing machine. 12 3 45 No. Part Name Part Code 1 Pen tablet XF0178-001 2 Tablet pen XF2797-001 3 Tablet pen holder XF0185-001 4 Extra pen tips (4) XF0183-001 5 Pen tip clip XF0184-001 WARNING Do not disassemble or modify the tablet pen/ battery. Do not use metallic objects, such as tweezers or a metallic pen, when changing the battery. Do not throw the battery into fire or expose to heat. Remove battery immediately and stop using the machine if you notice abnormal odor, heat, discoloration, deformation or anything unusual while using or storing it. CAUTION Remove the battery if you do not intend to use tablet pen for an extended period of time. Do not set the positive and negative ends of the battery in the wrong direction. Note Unscrew the upper barrel slowly, so that the tablet pen will not be damaged.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS 24 bGently pull the pen tip straight out. cPush in the new pen tip until it is flush with the tablet pen. ■Using with My Custom Design aSelect a favorite picture for creating embroidery pattern. bInsert the picture under the tablet sheet. cActivate My Custom Design, then trace the picture with the tablet pen. For detailed instructions about operating My Custom Design, refer to the Operation Manual (PDF format) stored on the My Custom Design CD. Note When you create the embroidery pattern by tracing the picture using the pen tablet, the actual size of the pattern will be bigger than the tracing picture. Check the size of the pattern before embroidering, then change the size of the pattern if needed. The pen tablet cannot be used as the USB mouse while tracing the picture. Operate with your finger or touch pen (stylus) while tracing.
Chapter 1 Getting Ready TURNING THE MACHINE ON/OFF ...............26 LCD SCREEN...................................................28 ■Home Page Screen ................................................................... 28 ■ Utility Stitch LCD Screen ......................................................... 29 ■ Key Functions ........................................................................... 30 USB Connectivity.............................................................. 32 ■Using USB Media or Embroidery Card Reader/ USB Card Writer Module*........................................................ 32 ■ Connecting the Machine to the Computer ............................... 33 ■ Using a USB Mouse .................................................................. 33 ■ Clicking a Key .......................................................................... 33 ■ Changing Pages ........................................................................ 33 ■ Using the Pen Tablet ................................................................ 34 Using the Machine Setting Mode Key ............................... 35 ■Saving a Settings Screen Image to USB Media .......................... 39 ■ Changing the Pointer Shape When a USB Mouse Is Used ........ 39 ■ Changing the Screen Saver Image ............................................ 40 ■ Selecting the Initial Screen Display .......................................... 41 ■ Choosing the Display Language................................................ 41 ■ Changing the Background Colors of the Embroidery Patterns ....................................................... 42 ■ Specifying the Size of Pattern Thumbnails................................ 43 Using the Sewing Machine Help Key ................................ 44 Using the Operation Guide Function ................................ 45 Using the Sewing Guide Function ..................................... 46 Using the Pattern Explanation Function ............................ 47 LOWER THREADING .....................................48 Winding the Bobbin .......................................................... 48 ■Using the Supplemental Spool Pin ............................................ 48 ■ Using the Spool Pin .................................................................. 51 ■ Using the Spool Stand .............................................................. 52 ■ Untangling Thread from Beneath the Bobbin Winder Seat....... 53 Setting the Bobbin ............................................................ 54 Pulling Up the Bobbin Thread........................................... 55 UPPER THREADING ....................................... 57 Upper Threading............................................................... 57 Using the Twin Needle Mode ........................................... 60 Using the Spool Stand ....................................................... 63 ■Using the Spool Stand .............................................................. 63Using Threads that Unwind Quickly ................................. 64 ■Using the Spool Net ................................................................. 64 CHANGING THE PRESSER FOOT ..................65 Removing the Presser Foot................................................ 65 Attaching the Presser Foot ................................................ 65 Attaching the Walking Foot .............................................. 66 CHANGING THE NEEDLE ..............................67 About the Needle.............................................................. 69 Fabric/Thread/Needle Combinations ................................ 69
TURNING THE MACHINE ON/OFF 26 TURNING THE MACHINE ON/OFF WARNING Use only regular household electricity for the power source. Using other power sources may result in fire, electric shock, or damage to the machine. Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and the power cord receptacle on the machine. Do not insert the plug on the power cord into an electrical outlet that is in poor condition. Turn the main power to OFF and remove the plug in the following circumstances: When you are away from the machine After using the machine When the power fails during use When the machine does not operate correctly due to a bad connection or a disconnection During electrical storms CAUTION Use only the power cord included with this machine. Do not use extension cords or multi-plug adapters with many other appliances plugged in to them. Fire or electric shock may result. Do not touch the plug with wet hands. Electric shock may result. When unplugging the machine, always turn the main power to OFF first. Always grasp the plug to remove it from the outlet. Pulling on the cord may damage the cord, or lead to fire or electric shock. Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted, or bundled. Do not place heavy objects on the cord. Do not subject the cord to heat. These things may damage the cord, or cause fire or electric shock. If the cord or plug is damaged, take the machine to your authorized dealer for repairs before continuing use. Unplug the power cord if the machine is not to be used for a long period of time. Otherwise, a fire may result. When leaving the machine unattended, either the main switch of the machine should be turned to OFF or the plug must be removed from the socket-outlet. When servicing the machine or when removing covers, the machine must be unplugged. For U.S.A only This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electrical shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way.
TURNING THE MACHINE ON/OFF Getting Ready 27 1 aInsert the power supply cord into the power cord receptacle, then insert the plug into a wall outlet. aMain power switch b Power supply cord bTurn the main power switch to “I” to turn on the machine. aOFF b ON cTurn the main power switch to “O” to turn off the machine. Memo When the machine is turned on, the needle and the feed dogs will make sound when they move; this is not a malfunction.
LCD SCREEN 28 LCD SCREEN When the machine is turned on, the opening movie is played. Touch anywhere on the screen for the home page screen to be displayed. Touch the LCD screen or a key with your finger or the included touch pen to select a machine function. ■Home Page Screen Note When the straight stitch needle plate is on the machine, the needle will automatically move to the mid- dle position. Memo Only touch the screen with your finger or the included touch pen. Do not use a sharp pencil, screw-driver, or other hard or sharp object. It is not necessary to press hard on the screen. Pressing too hard or using a sharp object may damage the screen. No.DisplayKey NameExplanationPag e a Sewing keyPress this key to sew utility stitches or character or decorative stitch patterns. See the “Key Functions” table. 30 b Embroidery key Attach the embroidery unit and press this key to embroider patterns.186 c Embroidery Edit key Press this key to combine embroidery patterns. With the embroidery edit functions, you can also create or iginal embroidery patterns or frame patterns. 264 b c a