Home > Brother > Sewing Machine > Brother Quattro 3 User Manual

Brother Quattro 3 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Brother Quattro 3 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 331 Brother manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							CONFIRMING THE PATTERN POSITION
    Embroidery
    209
    5
    cSelect the pattern on your sewing machine.
    dPress   in the sewing screen.
    ePress   to set the starting point to the 
    center of the pattern.
    fPress .
    gPress the “Presser Foot Lifter” button to 
    lower the presser foot.
    hPress .
    iPress the positioning keys to move the 
    embroidery frame until the cross-shaped 
    chalk mark drawn on the fabric is displayed 
    in the camera view window.
    aPositioning keys
    a 
    						
    							CONFIRMING THE PATTERN POSITION
    210
    jPress   to display the grid lines.
    aGrid lines
    b Chalk mark on the fabric
    kAdjust the orientation of the pattern by 
    pressing the orientation keys until the grid 
    lines are parallel with the chalk mark drawn 
    on the fabric. (Refer to “Rotating the 
    Pattern” on page 242.)
    aCenter point of the pattern
    lPress the positioning keys to move the 
    embroidery frame until the center point of 
    the pattern in the camera view window is 
    aligned with the chalk mark drawn on the 
    fabric.
    mPress   to return to the previous 
    screen.
    nPress the “Start/Stop” button to begin 
    embroidering.
    * See “Sewing Embroidery Patterns” on page 219.
    Memo
     Press   to enlarge the camera view. By 
    enlarging the camera view, you can make a close 
    adjustment for the center point of the pattern moving 
    the embroidery frame little by little.
    a
    ba 
    						
    							CONFIRMING THE PATTERN POSITION
    Embroidery
    211
    5
    Display the Fabric While 
    Aligning the Embroidering 
    Position
    The fabric hooped in the embroidery frame can be 
    displayed on the LCD so that the embroidery position 
    can be easily aligned.
    Example:
    aHoop the fabric in the embroidery frame, and 
    then attach the frame to the embroidery 
    machine.
    bSelect the pattern, and then press  .
    cPress .
    dWhen the following message appears, press .
    →The embroidery frame moves so the fabric can be 
    scanned.
    Note
     When embroidery frame (small: H 2 cm × W 6 cm (H 
    1 inch × W 2-1/2 inches)) is installed, the built-in 
    camera cannot be used to align the embroidering 
    position. Install medium embroidery frame or larger.
     For details on using thicker fabric such as quilting,  refer to “Positioning the Pattern on Thick Fabric” 
    (page 213).
    Note
     Check page 8/8 of Settings screen to make sure the 
    Fabric Thickness Sensor is turned off when using 
    light to medium weight fabrics.
    Memo
     If you do not wish the upper thread to be scanned together with the fabric, scan the fabric without the 
    needle threaded with the upper thread. 
    						
    							CONFIRMING THE PATTERN POSITION
    212
    eWhen the fabric appears as a background for 
    the pattern, the pattern can be moved if it is 
    necessary.
    fUse   to align the pattern to the desired 
    embroidery position.
      The pattern can be moved to the desired position by using your finger or the touch pen to drag the 
    pattern displayed on the screen.
    gPress the “Start/Stop” button to start 
    embroidering.
    * See “Sewing Embroidery Patterns” on page 219.
    → When embroidery is finished, the fabric displayed in 
    the background disappears.
    Whether the fabric disappears or remains displayed can 
    be specified from page 8/8 of the Settings screen.
    a Set to “ON” to leave the fabric displayed in the 
    background.
    b When set to “OFF”, the background will disappear.
    c Press   to remove the background image 
    completely.
    Memo
     If necessary, press   to display a preview in 
    order to check the pattern position.
    Note
     If the embroidery is not sewn the fabric background will remain on the screen.
    In Settings screen 8/8 press   to erase the 
    background image.
    b
    a
    c 
    						
    							CONFIRMING THE PATTERN POSITION
    Embroidery
    213
    5
    ■Positioning the Pattern on Thick 
    Fabric
    When positioning the pattern on thick fabric such as 
    quilting, the fabric may not be detected correctly. In 
    order for the fabric to be correctly detected, its 
    thickness must first be measured.
    aHoop the fabric in the embroidery frame, and 
    then attach the frame to the embroidery 
    machine.
    bSelect the pattern, and then press  .
    cDisplay page 8/8 of the Settings screen, and 
    then set “Fabric Thickness Sensor” to “ON”.
    dPress .
    ePress .
    fAffix the embroidery positioning sticker to the 
    fabric within the area indicated by the red 
    frame in the LCD, and then press  .
    gWhen the following message appears, remove 
    the embroidery positioning sticker, and then 
    press .
    → The embroidery frame is moved, and the 
    embroidery positioning sticker affixed to the fabric is 
    detected.
    hContinue with step f on page 212 to align 
    the pattern with the desired embroidery 
    position.
    Using the Built-In Camera to 
    Align the Embroidering Position
    The embroidering position can easily be aligned 
    using the machine’s built-in camera and the 
    included embroidery positioning sticker.
    aAffix the embroidery positioning sticker to 
    the location in the fabric to be 
    embroidered. Place the embroidery 
    positioning sticker so that the center of the 
    larger circle is at the center of the 
    embroidery pattern.
    a Embroidery positioning sticker
    b Center of the embroidery pattern
    c Embroidery field
    Memo
     This feature is functional only when the fabric is 
    scanned. It will not affect embroidering if it is turned 
    on with normal embroidery.
     CAUTION
     Use fabrics with a thickness of less than 3 mm  (approx. 1/8 inch). Using fabrics thicker than 3 mm 
    (approx. 1/8 inch) may cause the needle to break.
    Note
     When embroidery frame (small) is installed, the built-in camera cannot be used to align 
    the embroidering position. Install embroidery 
    frame (medium) or a larger embroidery 
    frame. 
    						
    							CONFIRMING THE PATTERN POSITION
    214
    bAfter selecting the pattern, press  , 
    and then press  .
    →A window appears so that the area containing the 
    embroidery positioning sticker can be selected.
    cFrom the areas shown in the window, select 
    the area containing the embroidery 
    positioning sticker.
    * If an area is not selected, scanning will start from the 
    center.
    Note
     When inserting the fabric in the embroidery frame, check that the embroidery pattern fits 
    within the embroidery field for the frame that 
    is used.
    a Embroidery field
    b Embroidery pattern
    c Embroidery positioning sticker
     Depending on the type of fabric that is used, 
    a part of the embroidery positioning sticker 
    may remain attached when it is peeled off. 
    Before using the embroidery positioning 
    sticker, check that it can be cleanly removed 
    from a scrap piece of the fabric to be used.
    Note
     Scanning cannot start from the center after an area has been selected. To scan from the 
    center, press   to close the window, 
    then display the window again but do not 
    select an area to scan, then press  .
     If the embroidery positioning sticker  overlaps two areas, select either of the two 
    areas. 
    						
    							CONFIRMING THE PATTERN POSITION
    Embroidery
    215
    5
    dPress .
    eFollowing message appears. Press  .
    →The built-in camera automatically searches for the 
    embroidery positioning sticker, and then the 
    carriage is moved so that the center of the 
    embroidery pattern is aligned with the center of the 
    embroidery positioning sticker. Regardless of the 
    setting selected in the machine settings screen, the 
    brightness of the light changes to “5” while the built-
    in camera searches for the embroidery positioning 
    sticker.
    fA reminder message appears. Remove the 
    embroidery positioning sticker from the 
    fabric, and press  .
    * To remove the embroidery positioning sticker more 
    easily, press   so that the embroidery frame 
    moves slightly forward and away from under the 
    needle. After the embroidery positioning sticker is 
    removed, press  .
    gPress the “Start/Stop” button to begin 
    embroidering.
    * See “Sewing Embroidery Patterns” on page 219.
    Note
     Attach embroidery foot “W2” before pressing  . The embroidery foot “W2” lowers 
    and check the fabric thickness, to help the 
    built-in camera recognize the embroidery 
    positioning sticker.
    Note
     If the following warning message appears, 
    touch   and reposition the embroidery 
    positioning sticker so the pattern is within 
    the embroidery field, and then press   
    again.
    Note
     After the included embroidery positioning stickers are used up, optional stickers are 
    available. For details, refer to “Options” on 
    page 20. 
    						
    							CONFIRMING THE PATTERN POSITION
    216
    Checking the Pattern Position 
    The embroidery frame moves and shows the 
    pattern position. Watch the frame closely to make 
    sure the pattern will be sewn in the right place.
    aPress .
    →The following screen is displayed.
    bFrom  , press the key for the position 
    that you want to check.
    aSelected position
    → The needle will move to the selected position on the 
    pattern.
    cPress . 
    Memo
     To see the entire embroidering area, press 
    . The embroidery frame moves and 
    shows the embroidery area.
     CAUTION
     Make sure the needle is up when the  embroidery frame is moving. If the needle is 
    down, it could break and result in injury.
    a 
    						
    							CONFIRMING THE PATTERN POSITION
    Embroidery
    217
    5
    Previewing the Completed 
    Pattern 
    aPress .
    →An image of the pattern as it will be embroidered 
    appears.
    bPress   to select the frame 
    used in the preview. 
    * Frames displayed in light gray cannot be selected. 
    * Press   to enlarge the image of the pattern.
    * The pattern can be sewn as it appears in the  following display.
    cPress   to return to the original screen. 
    Memo
     You can begin sewing from this screen by pressing the “Start/Stop” button. 
    						
    							SEWING AN EMBROIDERY PATTERN
    218
    SEWING AN EMBROIDERY PATTERN
    Sewing Attractive Finishes 
    There are many factors that go into sewing beautiful embroidery. Using the appropriate stabilizer (see 
    page 200) and hooping the fabric in the frame (see page 202) are two important factors mentioned earlier. 
    Another important point is the appropriateness of the needle and thread being used. See the explanation 
    of threads below. Included with this machine are two bobbin cases. Follow the explanation below.
    Thread Upper threadUse embroidery thread intended for use with this machine. 
    Other embroidery threads may not yield optimum results.
    Bobbin thread Use embroidery bobbin thread intended for use with this machine.
    Memo
     If you use threads other than those listed above, the embroidery may not sew out correctly. 
    Bobbin case
    aStandard bobbin case 
    (green marking on the screw)
    Alternate bobbin case 
    (no color on the screw)
    Standard bobbin case (green marking on the screw) is in the machine for sewing and embroidery. 
    The bobbin case originally installed in the machine has a green marking on the screw. Do not adjust 
    green marked screw.
    Alternate bobbin case (no color on the screw) is se t with tighter tension for embroidery with different 
    weights of bobbin threads and a variety of embroidery techniques. This bobbin case is identified 
    with a dark colored mark on the inside of the bobbin cavity. The screw on this case can be adjusted 
    if necessary.
    See page 338 for how to remove the bobbin case.
     CAUTION
     When embroidering on large garments (especially jackets or other heavy fabrics), do not let the fabric  hang over the table. Otherwise, the embroidery unit cannot move freely and the embroidery frame may 
    strike the needle, causing the needle to bend or break and possibly cause injury.
    Place the fabric so that it does not hang off the table or hold the fabric to keep it from dragging.
    Note
     Before embroidering, check that there is enough thread in the bobbin. If you start to sew your embroi-dery project without enough thread in the bobbin, you will need to rewind the bobbin in the middle of the 
    embroidery pattern.
     Do not leave objects in the range of motion of the embroidery frame. The frame may strike the object  and cause a poor finish to the embroidery pattern. 
     When embroidering on large garments (especially jackets or other heavy fabrics), do not let the fabric  hang over the table. Otherwise, the embroidery unit cannot move freely, and the pattern may not turn 
    out as planned.  
    						
    All Brother manuals Comments (0)

    Related Manuals for Brother Quattro 3 User Manual