Home > Brother > Sewing Machine > Brother Quattro 3 User Manual

Brother Quattro 3 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Brother Quattro 3 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 331 Brother manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							SEWING THE STITCHES
    Utility Stitches
    139
    3
    cCheck that the needle drops at the desired 
    position and lower the presser foot, making 
    sure the upper thread passes underneath 
    the buttonhole foot.
    dLower the buttonhole lever so that it is 
    positioned behind the metal bracket on the 
    buttonhole foot.
    aButtonhole lever
    a Metal bracket 
    eGently hold the end of the upper thread, 
    and then press the “Start/Stop” button to 
    start the machine. 
    →Once sewing is completed, the machine 
    automatically sews reinforcement stitches, and then 
    stops.
    Note
     Pass the thread underneath the presser 
    foot.
     Set the presser foot so that there is no gap  behind the section marked with an “A” (the 
    shaded area in the illustration below). If 
    there is a gap, the size of the darning will not 
    be correct. 
    Memo
     If automatic thread cutting is turned on before you start sewing, both threads are 
    automatically cut after the reinforcement 
    stitches are sewn. If the fabric does not feed 
    (for example, because it is too thick), 
    increase the stitch length setting.  
    						
    							SEWING THE STITCHES
    140
    Bar Tacks 
    Use bar tacks to reinforce areas that will be subject to strain, such as pocket corners. 
    aSelect .
    bAttach buttonhole foot “A” and set the 
    scale to the length of the bar tack you wish 
    to sew.
    aPresser foot scale 
    b Completed length measurement 
    c 5 mm (approx. 3/16 inch)
    cSet the fabric so that the pocket moves 
    toward you during sewing.
    dCheck the first needle drop point and lower 
    the presser foot.
    a2 mm (approx. 1/16 inch) 
    StitchStitch namePresser 
    footApplications
    Stitch width [mm (inch)]Stitch length  [mm (inch)]Tw in  
    needle
    AutoManualAutoManual
    Bar tack Reinforcement at opening of 
    pocket, etc.2.0
    (1/16) 1.0 - 3.0
    (1/16 - 1/8) 0.4
    (1/64) 0.3 - 1.0
    (1/64 - 1/16) NO
    Memo
     Bar tacks can be between 5 mm (approx. 
    3/16 inch) and 28 mm (approx. 1-1/16 
    inches). Bar tacks are usually between 5 
    mm (approx. 3/16 inch) and 10 mm (approx. 
    3/8 inch).
    Note
     Pass the thread underneath the presser 
    foot. 
     Slide the outside frame of the buttonhole  foot backward as far as possible as shown in 
    the illustration, making sure that there is no 
    gap behind the part of the foot marked “A”. If 
    the buttonhole foot is not slid back as far as 
    possible, the bar tack will not be sewn to the 
    correct size. 
    						
    							SEWING THE STITCHES
    Utility Stitches
    141
    3
    eLower the buttonhole lever so that it is 
    positioned behind the metal bracket on the 
    buttonhole foot.
    aMetal bracket 
    fGently hold the end of the upper thread and 
    begin sewing. 
    →When sewing is completed, the machine will sew 
    reinforcement stitches and stop automatically.
    ■Bar Tacks on Thick Fabrics
    Place a piece of folded fabric or cardboard beside 
    the fabric being sewn to level the buttonhole foot 
    and allow for easier and even feeding.
    a Presser foot 
    b Thick paper
    c Fabric
    Memo
     If automatic thread cutting is turned on 
    before you start sewing, both threads are 
    automatically cut after the reinforcement 
    stitches are sewn. If the fabric does not feed 
    (for example, because it is too thick), 
    increase the stitch length setting. 
    						
    							SEWING THE STITCHES
    142
    Button Sewing 
    Buttons with 2 or 4 holes can be attached, using the machine.
    aSelect .
    →The feed dogs are lowered automatically.
    bRaise the presser foot.
    cAttach button sewing foot “M”, slide the 
    button along the metal plate and into the 
    presser foot, and lower the presser foot.
    aButton
    b Metal plate
    dRotate the handwheel toward you 
    (counterclockwise) to check that the needle 
    goes into each hole correctly. 
    * If the needle does not reach the holes on the left 
    side, adjust the stitch width.
    * To attach the button more securely, repeat the  process. 
    eGently hold the end of the upper thread and 
    start sewing. 
    →The machine stops automatically when sewing is 
    finished.
    fFrom the wrong side of the fabric, pull the 
    end of the bobbin thread to pull the upper 
    thread through to the wrong side of the 
    fabric. Tie the two thread ends together and 
    cut the threads.
    gAfter the button is attached, select another 
    stitch and rotate the handwheel toward you 
    (counterclockwise) to raise the feed dogs.
    StitchStitch namePresser 
    footApplications
    Stitch width [mm (inch)]Stitch length  [mm (inch)]Tw in  
    needle
    AutoManualAutoManual
    Button sewing Attaching buttons
    3.5
    (1/8) 2.5 - 4.5
    (3/32 - 3/16) —
    —N O
    Note
     Do not use the automatic thread cutting function when sewing buttons. Otherwise, you will lose the 
    thread ends. 
     CAUTION
     Make sure the needle does not strike the 
    button during sewing. The needle may break 
    and cause injury.  
    						
    							SEWING THE STITCHES
    Utility Stitches
    143
    3
    ■Attaching 4 Hole Buttons
    Sew the two holes closest to you. Then raise the 
    presser foot and move the fabric so that the needle 
    goes into the next two holes, and sew them in the 
    same way. 
    ■Attaching a Shank to the Button 
    aPull the shank lever toward you before 
    sewing.
    a Shank lever 
    bPull the two ends of the upper thread 
    between the button and the fabric, wind 
    them around the shank, and then tie them 
    firmly together. 
    cTie the ends of the bobbin thread from the 
    beginning and end of sewing together on 
    the wrong side of the fabric.
    dCut off any excess thread.
    Note
     When sewing is completed, be sure to select 
    the other stitch and rotate the handwheel 
    toward you (counterclockwise) to raise the 
    feed dogs. 
    						
    							SEWING THE STITCHES
    144
    Eyelet 
    Use this stitch for making belt holes and other similar applications.
    aSelect  or .
    bUse     in either the stitch width 
    display or the stitch length display to 
    choose the size of the eyelet.
    * Actual size
    aLarge 7 mm (approx. 1/4 inch)
    b Medium 6 mm (approx. 15/64 inch)
    c Small 5 mm (approx. 3/16 inch)
    cAttach monogramming foot “N”, then 
    rotate the handwheel toward you 
    (counterclockwise) to check the needle 
    drop position. 
    aNeedle drop position 
    dLower the presser foot and start sewing.
    →When sewing is finished, the machine sews 
    reinforcement stitches and stops automatically.
    eUse the eyelet punch to make a hole in the 
    center of the stitching.
    StitchStitch namePresser 
    footApplications
    Stitch width [mm (inch)]Stitch length  [mm (inch)]Twi n  
    needle
    AutoManualAutoManual
    Eyelet For making eyelets, holes on 
    belts, etc.7.0
    (1/4) 7.0 6.0 5.0
    (1/4 15/64 3/16) 7.0
    (1/4) 7.0 6.0 5.0
    (1/4 15/64 3/16) NO
    Star eyelet For making star-shaped eyelets 
    on holes.
    ——— —N O
    Note
     Only one size is available for  .
    Note
     If the stitch pattern comes out poorly, make 
    adjustments to “SEWING STITCH 
    PATTERNS” on page 161. 
    						
    							SEWING THE STITCHES
    Utility Stitches
    145
    3
    Multi-directional Sewing 
    (Straight Stitch and Zigzag Stitch) 
    Use these stitch patterns to attach patches or 
    emblems to pant legs, shirt sleeves, etc.
    aRemove the flat bed attachment to use the 
    free-arm.
    bSelect   and attach monogramming foot 
    “N”.
    cSet the needle in the fabric at the sewing 
    start point, and sew seam “1” as shown.
    aStart Point 
    dSelect   and sew seam “2” as shown. 
    * The fabric will move sideways, guide the fabric by 
    hand to keep sewing straight.
    eSelect   and sew seam “3” as shown. 
    →The fabric feeds forward while stitching backward.
    fSelect   and sew seam “4” as shown. 
    →The seam will be connected to the starting point of 
    seam 1.
    Memo
     Insert the tubular piece of fabric onto the 
    free-arm, and then sew in the order shown in 
    the illustration.
    Memo
     For details on each stitch, refer to the “STITCH SETTING CHART” at the end of 
    this manual. 
    						
    							SEWING THE STITCHES
    146
    Zipper Insertion 
    ■Centered Zipper 
    Use for bags and other such applications. 
    aSelect .
    bAttach presser foot “J” and sew straight 
    stitches up to the zipper opening. Change to 
    a basting stitch (see page 98) and sew to the 
    top of the fabric.
    a Basting stitches 
    b Reverse stitches 
    c End of zipper opening 
    d Wrong side 
    cPress the seam allowance open and attach 
    the zipper with a basting stitch in the 
    middle of each side of the zipper tape.
    aBasting stitches 
    b Zipper 
    c Wrong side 
    dRemove presser foot “J”. Align the right 
    side of the pin in zipper foot “I” with the 
    presser foot holder, and attach the zipper 
    foot.
    aRight 
    b Left 
    c Needle drop position 
    eTopstitch 7 to 10 mm (approx. 1/4 to 
    3/8 inch) from the seamed edge of the 
    fabric, then remove the basting.
    Memo
     For details on each stitch, refer to the 
    “STITCH SETTING CHART” at the end of 
    this manual.
    Note
     Make sure you sew using the middle needle 
    position. 
     CAUTION
     When using zipper foot “I”, make sure the 
    straight stitch, middle needle position is 
    selected. Rotate the handwheel toward you 
    (counterclockwise) to make sure the needle 
    does not strike the presser foot. If another 
    stitch is selected, the needle will strike the 
    presser foot, causing the needle to break and 
    possibly causing injury.
     CAUTION
     Make sure the needle does not strike the zipper during sewing. If the needle strikes the 
    zipper, the needle may break, leading to 
    injury. 
    						
    							SEWING THE STITCHES
    Utility Stitches
    147
    3
    ■Inserting a Side Zipper 
    Use for side zippers in skirts or dresses. 
    aSelect .
    bAttach presser foot “J” and sew straight 
    stitches up to the zipper opening. Change to 
    a basting stitch and sew to the top of the 
    fabric.
    a Reverse stitches 
    b Wrong side of fabric 
    c Basting stitches 
    d End of zipper opening 
    cPress the seam allowance open and align 
    the folded hem along the teeth of the 
    zipper, while maintaining 3 mm (approx. 
    1/8 inch) of sewing space.
    aZipper pull tab 
    b Wrong side of fabric 
    c Zipper teeth 
    d End of zipper opening 
    e 3 mm (approx. 1/8 inch) 
    dRemove presser foot “J”. 
    eAlign the right side of the pin in zipper foot 
    “I” with the presser foot holder, and attach 
    the presser foot.
    aRight 
    b Left 
    c Needle drop position
    fSet the presser foot in the 3 mm (approx. 
    1/8 inch) margin. 
    gStarting from the end of the zipper opening, 
    sew to a point about 50 mm (approx. 
    2 inches) from the edge of the fabric, then 
    stop the machine. 
    hPull down the zipper slider, then continue 
    sewing to the edge of the fabric.
    a50 mm (approx. 2 inches) 
    b 3 mm (approx. 1/8 inch) 
    Note
     Make sure you sew using the middle needle 
    position. 
     CAUTION
     When using zipper foot “I”, make sure the 
    straight stitch, middle needle position is 
    selected. Rotate the handwheel toward you 
    (counterclockwise) to make sure the needle 
    does not strike the presser foot. If another 
    stitch is selected, the needle will strike the 
    presser foot, causing the needle to break and 
    possibly causing injury.
     CAUTION
     Make sure the needle does not strike the zipper during sewing. If the needle strikes the 
    zipper, the needle may break, leading to 
    injury. 
    						
    							SEWING THE STITCHES
    148
    iClose the zipper, turn the fabric over, and 
    sew a basting stitch.
    aFront of the skirt (wrong side of fabric) 
    b Basting stitches 
    c Front of the skirt (right side of fabric) 
    d Back of the skirt (right side of fabric) 
    jRemove the presser foot, and reattach it so 
    that the left side of the pin is attached to the 
    presser foot holder.
    * When sewing the left side of the zipper, the needle 
    should drop on the right side of the presser foot. 
    When sewing the right side of the zipper, the needle 
    should drop on the left side of the presser foot.
    a Right 
    b Left 
    c Needle drop position 
    kSet the fabric so that the left edge of the 
    presser foot touches the edge of the zipper 
    teeth. 
    lSew reverse stitches at the top of the 
    zipper, then continue sewing. 
    mStop sewing about 50 mm (approx. 
    2 inches) from the edge of the fabric, leave 
    the needle in the fabric, and remove the 
    basting stitches. 
    nOpen the zipper and sew the rest of the 
    seam.
    aBasting stitches 
    b 7 to 10 mm (approx. 1/4 inch to 3/8 inch) 
    c Reverse stitches 
    d 50 mm (approx. 2 inches) 
    Edge Sewing
    Using the built-in camera, the width of the area 
    from the edge of the fabric to the stitching line can 
    be measured and set for edge sewing.
    This function can be used when the edge of the 
    fabric is straight or a gentle curve.
    aStraight
    b Curved 
    						
    All Brother manuals Comments (0)

    Related Manuals for Brother Quattro 3 User Manual