Brother Laserprinter Hl 1650 1670n User Guide
Have a look at the manual Brother Laserprinter Hl 1650 1670n User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 331 Brother manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
4-10 ♦ Minimum memory recommendation HL-1650 (Including 8 Mbytes of internal memory) HP LaserJet, EPSON FX-850, and IBM Proprinter XL emulation modes 300 dpi 600 dpi HQ1200 Letter/A4 Standard Standard 24 Mbytes Legal Standard Standard 24 Mbytes BR-Script 3 mode 300 dpi 600 dpi HQ1200 Letter/A4 Standard Standard 24 Mbytes Legal Standard Standard 24 Mbytes Duplex printing 300 dpi 600 dpi HQ1200 HP LaserJet Standard 24 Mbytes 40 Mbytes BR-Script 3 Standard 24 Mbytes 40 Mbytes
CHAPTER 4 OPTIONS 4-11 HL-1670N (Including 16 Mbytes of internal memory) HP LaserJet, EPSON FX-850, and IBM Proprinter XL emulation modes 300 dpi 600 dpi HQ1200 Letter/A4 Standard Standard Standard Legal Standard Standard Standard BR-Script 3 mode 300 dpi 600 dpi HQ1200 Letter/A4 Standard Standard Standard Legal Standard Standard Standard Duplex printing 300 dpi 600 dpi HQ1200 HP LaserJet Standard Standard 32 Mbytes BR-Script 3 Standard Standard 32 Mbytes
4-12 The following DIMM size can be installed: •16 Mbyte TECHWORKS PM-HP 16M-BR 32 Mbyte TECHWORKS PM-HP 32M-BR 64 Mbyte TECHWORKS PM-HP 64M-BR 128 Mbyte TECHWORKS PM-HP 128M-BR In general, DIMM must have the following specifications: Type: 100 pin and 32 bit output CAS Lantency 2 or 3 Clock Frequency 66MHz or more Capacity: 16, 32, 64 Mbyte or 128 Mbyte Height: 46mm (1.8 inches) or less Parity NONE Dram Type: SDRAM 4 Bank SDRAM can be used. Note •For more information, consult the dealer where you purchased the printer. •For the latest information, please visit our user support web site.
CHAPTER 4 OPTIONS 4-13 I I n n s s t t a a l l l l i i n n g g a a d d d d i i t t i i o o n n a a l l m m e e m m o o r r y y Install additional memory (DIMM) as follows: ☛ ☛☛ ☛ 1.Turn off the printer, and then unplug the power cord from the AC outlet. Disconnect the interface cable (printer cable) from the printer. Note Be sure to turn off the power to the printer before you install or remove the DIMM. ☛ ☛☛ ☛ 2.Open the Interface cover. Fig. 4-9
4-14 ☛ ☛☛ ☛ 3.Unscrew the two screws that secure the PCB access plate. Slide the plate toward you and remove it. Fig. 4-10 ☛ ☛☛ ☛ 4.Unpack the DIMM and hold it by the edges. !Caution DIMM boards can be damaged by even a small amount of static electricity. Do not touch the memory chips or the board surface. Wear an antistatic wrist strap when you install or remove the board. If you do not have an antistatic wrist strap, frequently touch the bare metal on the printer. ☛ ☛☛ ☛ 5.Holding the DIMM by the edges, align the notches on the DIMM with the DIMM slot.
CHAPTER 4 OPTIONS 4-15 ☛ ☛☛ ☛ 6.Press the DIMM straight into the slot (press firmly). Make sure the locks on each side of the DIMM snap inward into place. (To remove a DIMM, the locks must be released.) Fig. 4-11 ☛ ☛☛ ☛ 7.Install the PCB access plate. Secure the PCB access plate with the two screws. Fig. 4-12
4-16 ☛ ☛☛ ☛ 8.Close the Interface cover. Fig. 4-13 ☛ ☛☛ ☛ 9.Reconnect the interface cable (printer cable) from your computer. Plug the power cord into the AC outlet, and then turn on the power switch. ☛ ☛☛ ☛ 10.After you turn on the printer, the current RAM disk size will appear on the LCD. Check it to make sure you added the new memory correctly.
CHAPTER 4 OPTIONS 4-17 I I r r D D A A i i n n t t e e r r f f a a c c e e ( ( I I R R - - 1 1 0 0 0 0 0 0 ) ) IR-1000 connects to any printer and print data without connecting cables. • Support IrDA1.1 Infrared communication standard. • Fully compatible with Windows ® 95/98/Windows® Me, Windows NT® 4.0,Windows® 2000 Infrared printer device. • Transmits and receivers data up to 4 Mbits/s. • Connects to PC parallel port and connects to Centronic port on printer. • Allows a printer to communicate with an infrared-equipped portable computer. • Transmission range : 1 cm (0.39 inch) up to 100 cm (39 inch) meet IrDA standard. • 30 degrees cone angle. • Selects between infrared or parallel port. Fig. 4-14
4-18 O O p p t t i i o o n n a a l l f f o o n n t t p p a a c c k k a a g g e e ( ( B B S S - - 3 3 0 0 0 0 0 0 ) ) The optional font package (BS-3000) is a CD-ROM from which you can install the 136 PS3 Agfa TrueType Fonts.
CHAPTER 5 MAINTENANCE 5 5C C H H A A P P T T E E R R 5 5 R R O O U U T T I I N N E E M M A A I I N N T T E E N N A A N N C C E E