Brother Laserprinter Hl 1650 1670n User Guide

							CHAPTER 4 OPTIONS
4
4C
C
H
H
A
A
P
P
T
T
E
E
R
R
 
 
4
4
O
O
P
P
T
T
I
I
O
O
N
N
S
S 
						

							CHAPTER 4 OPTIONS
4-1
O O
p p
t t
i i
o o
n n
a a
l l
   
a a
c c
c c
e e
s s
s s
o o
r r
i i
e e
s s
This printer has the following optional accessories. You can increase the
capabilities of the printer with these items.
♦ Options
Lower tray unit Network board Additional memory IrDA interface
LT-500 NC-4100h 100pin DIMM IR-1000
See Lower tray unit
in this chapterSee Network option
in this chapterSee RAM expansion
in this chapterSee IrDA interface in
this chapter
Optional font
package
BS-3000
See Optional font
package in this
chapter 
						

							4-2
L L
o o
w w
e e
r r
   
t t
r r
a a
y y
   
u u
n n
i i
t t
   
( (
L L
T T
- -
5 5
0 0
0 0
) )
The Lower tray unit (tray 2) is a device that functions as an additional paper
source. It can hold a maximum of 250 sheets of paper (80 g/m2 or 21 lb.).
Expands up to 600 sheets total
Fig. 4-1
To purchase the optional Lower tray unit (tray 2), consult the dealer where
you purchased the printer.
Multi-purpose tray
(MP tray)
100 sheets
Lower tray unit
(Tray 2)
250 sheets
Paper cassette
(Tray 1)
250 sheets 
						

							CHAPTER 4 OPTIONS
4-3
I I
n n
s s
t t
a a
l l
l l
i i
n n
g g
   
t t
h h
e e
   
L L
o o
w w
e e
r r
   
t t
r r
a a
y y
   
u u
n n
i i
t t
Install the optional Lower tray unit under the printer as follows:
☛
☛☛ ☛ 1.Turn off the power switch, and then unplug the power cord.
☛
☛☛ ☛ 2.Close the Process cover, Multi-purpose tray, Face up output tray and Extension
flap.
☛
☛☛ ☛ 3.Lift the printer carefully with both hands and place it on top of the Lower tray
unit, so that the alignment pins of the Lower tray unit are inserted into the guide
holes in the underside of the printer.
Fig. 4-2
Follow the instructions supplied with the Lower tray unit. 
						

							4-4
Change the following settings in the printer driver Properties tab.
Select the
paper size.
Select the Paper
Source and Media
type. 
						

							CHAPTER 4 OPTIONS
4-5
N N
e e
t t
w w
o o
r r
k k
   
o o
p p
t t
i i
o o
n n
   
( (
N N
C C
- -
4 4
1 1
0 0
0 0
h h
) )
Installing the Network board enables you to use the printer in the TCP/IP,
IPX/SPX, AppleTalk, DLC/LLC, Banyan VINES, DEC LAT and NetBEUI
environments.  Also, useful utilities such as BR-Admin 32 and Network
Printing software for the administrator are included.
For more information about Set Up, see the Network User’s Guide.
I I
n n
s s
t t
a a
l l
l l
i i
n n
g g
   
t t
h h
e e
   
N N
e e
t t
w w
o o
r r
k k
   
b b
o o
a a
r r
d d
   
   
☛
☛☛ ☛ 1.Turn off the printer, and then unplug the power cord. Disconnect the interface
cable (printer cable) from the printer.
 
 
 
☛
☛☛ ☛ 2.Open the Interface cover.
 Fig. 4-3 
						

							4-6
☛
☛☛ ☛ 3.Unscrew the two screws that secure the PCB access plate. Remove the plate.
 
 
 
 
 
Fig. 4-4
 
 
 
☛
☛☛ ☛ 4.Remove the two screws securing the Network board cover plate and remove
the plate.
 Fig. 4-5
☛
☛☛ ☛ 5.Unpack the Network board. 
						

							CHAPTER 4 OPTIONS
4-7
 
☛
☛☛ ☛ 6.Insert the Network board connector into the PCB connector, and then secure it
with the two screws removed in Step 4.
 
 
 
Fig. 4-6
 
 
 
☛
☛☛ ☛ 7.Re-install the PCB access plate, and then secure it with the two screws you
removed in Step 3.
 
 
 
 
 
Fig. 4-7
  
						

							4-8
 
☛
☛☛ ☛ 8.Close the Interface cover.
 
 
 
 
 
Fig. 4-8
 
 
 
☛
☛☛ ☛ 9.Plug the power cord into the AC outlet, and then turn on the power switch. 
						

							CHAPTER 4 OPTIONS
4-9
R R
A A
M M
   
e e
x x
p p
a a
n n
s s
i i
o o
n n
HL-1650:
This printer has 8 Mbytes of standard memory and one slot for optional
expansion memory.  The memory can be expanded up to 136 Mbytes by
installing commercially available dual in-line memory modules (DIMMs).
(The standard memory installed varies depending on the  country where it is
purchased.)
HL-1670N:
This printer has 16 Mbytes of standard memory and one slot for optional
expansion memory.  The memory can be expanded up to 144 Mbytes by
installing commercially available dual in-line memory modules (DIMMs).
(The standard memory installed varies depending on the country where it is
purchased.)
This printer uses memory modules that are: 100 pins, no-parity, SDRAM with
64Mbit or more.  This printer is not compatible with Extended Data Output
(EDO) DIMM, or DIMM that uses 16 Mbit SDRAM.