BenQ Projector SU964 User Manual

  51
  Using the projector
EnglishSource menu
FunctionDescription
Quick Search
Sets whether the projector searches automatically for input sources. If the 
source scan is On, the projector will scan for input sources until it acquires a 
signal. If the function is not activated, the projector selects the last used input 
source.
HDMI Format
Selects an input source type for the HDMI signal. Auto is the default and 
recommended setting. You can also manually select the source type. The 
different source...

52 Using the projector  
EnglishSystem Setup: Basic menu
FunctionDescription
Language
Sets the language for the On-Screen Display (OSD) menus. See Using the 
menus on page 22 for details.
Projector InstallationThe projector can be installed on a ceiling or behind a screen, or with one or 
more mirrors. See Choosing a location on page 12 for details.
Menu Settings
Menu Display Time
Sets the length of time the OSD will remain active after your last key press. The 
range is from 5 to 30 seconds in 5-second...

  53
  Using the projector
EnglishSystem Setup: Advanced menu
FunctionDescription
High Altitude
A mode for operation in areas like high altitude or high temperature. See 
Operating in a high altitude environment on page 42 for details.
Lamp Settings
Lamp Mode
Selects the projector lamp power among Normal-Dual, Economic-Dual, 
Normal-Single Alternative, and Economic-Single Alternative modes. See 
Setting the lamp mode on page 37 for details.
Reset Lamp 1 Timer/Reset Lamp 2 Timer
Once the lamp is renewed,...

54 Using the projector  
English
Closed Caption
Closed Caption Enable
Activates the function by selecting On when the selected input signal carries 
closed captions.
•  Captions: An on-screen display of the dialogue, narration, and sound effects 
of TV programs and videos that are closed captioned (usually marked as 
CC in TV listings).
Caption Version
Selects a preferred closed captioning mode. To view captions, select CC1, 
CC2, CC3, or CC4 (CC1 displays captions in the primary language in your...

  55
  Using the projector
EnglishInformation menu
This menu shows you the current operating status of the projector.
Some picture adjustments are available only when certain input sources are in use. Unavailable adjustments 
are not shown on the screen.
FunctionDescription
Source
Shows the current signal source.
Picture ModeShows the selected mode in the Picture > Picture Mode menu.
Lamp ModeShows the selected lamp mode in the System Setup: Advanced > Lamp 
Mode
 menu.
ResolutionShows the native...

56 Additional information  
English
Additional information
Care of the projector
Your projector needs little maintenance. The only thing you have to do on a regular basis is keep the lens 
clean. Never remove any parts of the projector except the lamp. Contact your dealer or local customer 
service center if the projector fails to operate as expected.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface. Before you attempt to clean the lens, 
turn the projector off, unplug the...

  57
  Additional information
EnglishLamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by 
the built-in timer.
To obtain the lamp hour information:
1. Press MENU/EXIT and then press  /  until the System Setup: Advanced menu is highlighted.
2. Press   to highlight Lamp Settings and press ENTER. The Lamp Settings page is displayed.
3. Press   to highlight Lamp Information and press ENTER. The Lamp Information...

58 Additional information  
EnglishTiming of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, 
please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector 
and in some instances the lamp may explode. Go to http://www.BenQ.com for a replacement lamp.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn 
the power off and let the projector cool...

  59
  Additional information
EnglishReplacing the lamp
•  To reduce the risk of electrical shock, always turn the projector off and disconnect the power cable 
before changing the lamp.
•  To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the 
lamp.
•  To reduce the risk of injuries to fingers and damage to internal components, use caution when removing 
lamp glass that has shattered into sharp pieces.
•  To reduce the risk of injuries to fingers...

60 Additional information  
English1. Turn the power off and disconnect the 
projector from the power outlet. Turn off all 
connected equipment and disconnect all other 
cables. See Turning the projector off on 
page 43 for details.
2. Loosen the screw on the lamp cover.
3. Remove the lamp cover. 
4. Identify the lamp you want to replace by 
looking at the top of the lamp.5. Loosen the screw that hold the lamp to the 
projector. Disconnect the lamp connector 
from the projector.
6. Lift the handle so...