BenQ Projector SU964 User Manual

  21
  Using the projector
EnglishSelecting an input source
The projector can be connected to multiple equipment at the same 
time. When the projector is first turned on, it will attempt to 
reconnect with the input source which was in use when the projector 
was last shut down.
To select the video source:
•  Using the remote control
Press one of the Source keys on the remote control.
•  Using the OSD menu
Press SOURCE and then press  /  until your desired signal is selected 
and press ENTER.
Once...

22 Using the projector  
EnglishUsing the menus
The projector is equipped with multilingual On-Screen Display (OSD) menus for making various 
adjustments and settings.
Below is the overview of the OSD menu.
The OSD screenshots below are for reference only, and may differ from the actual design.
To use the OSD menus, please set the OSD menu to your familiar language.
Picture Mode
Reference Mode
Brightness
Contrast
Tint
Sharpness
Rename User Mode
Reset Picture Settings
Picture
+ 3
Video
Cinema
Current...

  23
  Using the projector
EnglishSecuring the projector
Using a security cable lock
The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a lock, such as the 
Kensington lock, to secure the projector. You can locate a Kensington lock slot on the projector. See item 
5 on page 9 for details. 
A Kensington security cable lock is usually a combination of key(s) and the lock. Refer to the locks 
documentation for finding out how to use it.
Utilizing the password function...

24 Using the projector  
EnglishIf you forget the password
If the password function is activated, you will be asked to enter the six-digit password every time you 
turn on the projector. If you enter the wrong password, the password error message is displayed lasting 
for three seconds, and the Input Password page follows. You can retry by entering another six-digit 
password, or if you did not record the password in this manual, and you absolutely do not remember it, 
you can use the password recall...

  25
  Using the projector
EnglishChanging the password
1. In the System Setup: Advanced > Security Settings menu, press  /  to highlight Change 
Password and press ENTER. The Change Password page is displayed. 
2. Enter the old password.
•  If the password is correct, the message Input New Password is displayed. 
•  If the password is incorrect, the password error message is displayed lasting for three seconds, 
and the message Input Current Password is displayed for your retry. You can press 
MENU/EXIT...

26 Using the projector  
EnglishAdjusting the projected image
Adjusting the projection angle 
There are four adjuster feet on the bottom of the projector. These can 
be used if necessary to change the projection angle. Screw the feet in or 
out as appropriate to aim and level the projection angle.
If the screen and the projector are not perpendicular to each other, the 
projected image becomes vertical trapezoidal. To correct this problem, see 
Correcting picture distortion on page 27 for details....

  27
  Using the projector
EnglishCorrecting picture distortion
Keystoning occurs when the projector is not perpendicular to the screen and is where the projected 
picture displays visible as a trapezoid shape like either of the following:
•  Two parallel sides (left and right, or top and bottom) but is noticeably wider on either side.
•  No parallel sides.
To correct the picture’s shape, you can perform the following steps.
1. Adjust the projection angle. Move the projector to be in front of the center...

28 Using the projector  
EnglishUsing the preset and user modes
Selecting a preset mode
The projector is preset with several pre-defined picture modes so that you can choose one to suit your 
operating environment and input source picture type.
To select a picture mode that suits your need:
• Press MODE repeatedly until your desired mode is selected.
•  Using the OSD menu
1. Press MENU/EXIT and then press  /  until the Picture menu is 
highlighted.
2. Press   to highlight Picture Mode.
3. Press  /  until...

  29
  Using the projector
EnglishSetting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not suitable for your need. 
You can use one of the picture modes (except the selected User mode) as a starting point and customize 
the settings.
1. In the Picture menu, highlight Picture Mode and press  /  to select User 1 or User 2 mode.
2. Press  to highlight Reference Mode.
This function is only available when User 1 or User 2 mode is selected up in the...

30 Using the projector  
EnglishFine-tuning the picture quality
No matter what picture mode you have selected, you are able to fine-tune those settings to fit every 
presentation purpose. Those adjustments will be saved to the preset mode you are at when you exit the 
OSD menu.
Adjusting Brightness
Highlight Brightness in the Picture menu and adjust the 
values by pressing  /  on the projector or remote 
control.
The higher the value, the brighter the picture. And the 
lower the setting, the darker the...