BenQ Projector SU964 User Manual

  41
  Using the projector
EnglishThe info page displays the informat ion and status of this projector.
For more information, visit  http://www.crestron.com & www.crestron.com/getroomview .
Press Exit to go 
back to the 
remote network  operation page. 

42 Using the projector  
EnglishOperating in a high altitude environment
We recommend that you activate High Altitude when your environment is higher than 1500 meters 
(around 4920 feet) above sea level, or whenever the projector will be used for extended periods of time 
(>10 hours) without shutdown.
To activate High Altitude:
1. Press MENU/EXIT and then press  /  until the System Setup: Advanced menu is highlighted.
2. Press   to highlight High Altitude.
3. Press /  to select On. A confirmation message...

  43
  Using the projector
EnglishTurning the projector off
To turn the projector off, press POWER ( ) on the projector or 
OFF   on the remote control and a warning message appears. 
Press POWER/OFF ( ) again.
•  The Power indicator light flashes orange and the fans run for 
about two minutes to cool the lamp. The projector will not 
respond to any commands until the cooling process is complete.
•  Then, the Power indicator light is a steady orange once the 
cooling process has finished and fans stop.
•...

44 Using the projector  
EnglishOn-Screen Display (OSD) menus
On-Screen Display (OSD) structure
Please note that the on-screen display (OSD) menus vary according to the signal type selected.
Main menuSub-menuOptions
Picture
Picture Mode Dynamic/Presentation/sRGB/Cinema/3D/User 1/User 2
Reference Mode Dynamic/Presentation/sRGB/Cinema/User 1/User 2
Brightness 0–100
Contrast 0–100
Color 0–100
Tint 0–100
Sharpness 0–15
Advanced...Black Level 0 IRE/7.5 IRE
Noise Reduction 0-31
Color Temperature...

  45
  Using the projector
English
Main menuSub-menuOptions
Display
Wall ColorOff/Light Yellow/ Pink/ Light Green/ 
Blue/ Blackboard
Aspect Ratio Auto/Real/4:3/16:9/16:10
Overscan Adjustment 0/1/2/3
2D Keystone
Corner FitTop Left/Top Right/Bottom Left/
Bottom Right
3D3D ModeAuto/3D Off/Frame Sequential/Frame 
Packing/Top-Bottom/Side-by-Side
3D Sync Invert Disable/Invert
Save 3D Settings3D settings 1/ 3D settings 2/ 
3D settings 3
Apply 3D Settings3D settings 1/ 3D settings 2/ 
3D settings 3/ Off
Source...

46 Using the projector  
English
System 
Setup: Basic
Language
Projector 
InstallationFront/Rear/Rear Ceiling/Front Ceiling
Menu SettingsMenu Display Time 5 sec/10 sec/20 sec/30 sec/Always
Menu PositionCenter/Top-Left/Top-Right/Bottom-
Right/Bottom-Left
Reminder Message On/Off
Operation SettingsDirect Power On On/Off
Signal Power On On/Off
Auto Power OffDisable/3 min/10 min/15 min/20 min/25 
min/30 min
Blank TimerDisable/5 min/10 min/15 min/20 min/25 
min/30 min
Sleep TimerDisable/30 min/1 hr/2 hr/3 hr/4...

  47
  Using the projector
English
Main menuSub-menuOptions
System 
Setup: 
Advanced
High Altitude On/Off
Lamp SettingsLamp ModeNormal-Dual / Economic-Dual / 
Normal-Single Alternative / 
Economic-Single Alternative
Reset Lamp 1 Timer Reset / Cancel
Reset Lamp 2 Timer Reset / Cancel
Lamp InformationLamp 1 Usage Time
Normal Mode
Economic Mode
Lamp 2 Usage Time
Normal Mode
Economic Mode
Equivalent Lamp 1 Hour
Equivalent Lamp 2 Hour
Security SettingsPower On Lock On/Off
Change Password
Serial Port...

48 Using the projector  
English
Note that the menu items are available when the projector detects at least one valid signal. If there is no 
equipment connected to the projector or no signal detected, limited menu items are accessible.
System 
Setup: 
AdvancedExpert ModeExpert Mode On/Off
Mode Selection Expert Mode 1/Expert Mode 2
Picture AdjustmentBrightness 0 ~ 100
Contrast 0 ~ 100
Color 0 ~ 100
Tint 0 ~ 100
Sharpness 0 ~ 15
Color TemperatureExpert 1/Expert2/Cool/Normal/Warm/
Lamp Native
White...

  49
  Using the projector
EnglishPicture menu
Picture menu (Advanced)
FunctionDescription
Picture Mode
Pre-defined picture modes are provided so you can optimize your projector 
picture set-up to suit your program type. See Selecting a preset mode on 
page 28 for details.
Reference Mode
Selects a preset mode that most suits your need for the picture quality and 
further fine-tune the picture based on the selections listed below. See Setting 
the User 1/User 2 mode on page 29 for details....

50 Using the projector  
EnglishDisplay menu
FunctionDescription
Wall Color
Corrects the projected picture’s color when the projection surface is not 
white. See Setting a wall color on page 35 for details.
Aspect RatioThere are several options to set the picture’s aspect ratio depending on your 
input source. See Selecting the aspect ratio on page 34 for details.
Overscan Adjustment
Conceals the poor picture quality in the four edges. You can also manually press 
/  to decide how much to be concealed....