BenQ Projector SU964 User Manual

  31
  Using the projector
EnglishAdvanced picture quality controls
There are more advanced functions in the Picture > Advanced... menu to be adjusted to your 
preference. To save the settings, just press MENU/EXIT to leave the OSD menu.
Setting Black Level
Highlight Black Level and press  /  on the projector or remote control to select 0 IRE or 7.5 IRE.
The grayscale video signal is measured in IRE units. In some areas which use NTSC TV standard, the 
grayscale is measured from 7.5 IRE (black) to 100...

32 Using the projector  
EnglishSetting a preferred color temperature
To set a preferred color temperature:
1. Highlight Color Temperature and select Cool, Normal, Wa r m or Lamp Native by pressing 
/  on the projector or remote control.
2. Press  to highlight Color Temperature Fine Tuning and press ENTER. The Color 
Temperature Fine Tuning page is displayed.
3. Press  /  to highlight the item you want to change and adjust the values by pressing  / .
• Red Gain/Green Gain/Blue Gain: Adjusts the contrast...

  33
  Using the projector
EnglishThe 3D Color Management provides six sets (RGBCMY) of colors to be adjusted to favorite colors. 
When you select each color, you can independently adjust its color range and saturation according to 
your preference.
To adjust and store the settings:
1. In the Picture menu, highlight Advanced... and press ENTER. 
Then, highlight 3D Color Management and press ENTER. The 
3D Color Management page is displayed.
2. Highlight Primary Color and press  /  to select a color from...

34 Using the projector  
EnglishSelecting the aspect ratio
The aspect ratio is the ratio of the image width to the image height. The default for this projector is 
16:10 while digital TV is usually in 16:9 ratio, and most analog TV signals and DVDs are in 4:3 ratio.
With the advent of digital signal processing, digital display devices like this projector can dynamically 
stretch and scale the image output to a different aspect than that of the image input source. Images can 
be stretched in a linear...

  35
  Using the projector
EnglishSetting a wall color
In the situation where you are projecting onto a colored surface such as a painted wall which may not be 
white, the Wall Color feature can help correct the projected picture’s color to prevent possible color 
difference between the source and projected pictures. There are several precalibrated colors to choose 
from: Light Yellow, Pink, Light Green, Blue, and Blackboard.
To select wall color:
1. Press MENU/EXIT and then press  /  until the Display...

36 Using the projector  
EnglishAdjusting the sound
The sound adjustments made (such as functions shown below) will have an effect on the projector 
speaker(s). Be sure you have made a correct connection to the projector audio input. See Connecting to 
video equipment on page 16 for how the audio input is connected.
•  Each time when you select a different source, the projector also changes the sound settings to which was 
last set for that particular source. 
•  Sound adjustments cannot be made during...

  37
  Using the projector
EnglishSetting the lamp mode
This projector is capable of dual-lamp projection and provides several lamp modes for different purposes:
You can perform one of the following methods to choose a lamp mode according to your preference.
Using the remote control:
1. Press Lamp Mode on your remote control, the lamp mode page is displayed.
2. Press   to highlight your preferred lamp mode and press ENTER.
Using the OSD menu:
1. Press MENU/EXIT and then press  /  until the System Setup:...

38 Using the projector  
EnglishSetting up the Wired LAN
1. Press MENU/EXIT and then press  /  until the System Setup: Advanced menu is highlighted.
2. Press  to highlight Serial Port Setting and press ENTER. The Serial Port Setting page is 
displayed.
3. Press  to highlight Channel and press ENTER. The Channel page is displayed.
4. Press  to highlight Wired LAN and press ENTER.
5. Press MENU/EXIT to return to System Setup: Advanced page.
Configuring the Wired LAN
If you are in a DHCP environment:
1....

  39
  Using the projector
EnglishControlling the projector re motely through a web browser
Once you have the correct IP address for the projecto r and the projector is on or in standby mode, you 
can use any computer that is on the same local area network to control the projector.
1. Enter the address of the projector in the address bar of your browser and click Go.
2. The remote network operation page opens. This pa ge allows you to operate the projector as if you 
were using the remote control or...

40 Using the projector  
EnglishThe tools page allows you to manage the projector,
 configure the LAN control settings and secure access 
of remote network operation on this projector.
i.You can name the projector, keep track of its location and the person in charge of it.
ii. You can adjust the  LAN Control Settings .
iii. Once set, access to the remote network op eration on this projector has been password-
protected.
iv. Once set, access to the tools pa ge has been password-protected.
After making the...