Barco Slm R12+ Owners Manual

8. Installation Mode
3. Push the cursor key↑or↓to highlightHighlighted item color.
OSD
HIGHLIGHT ITEM COLOR [red]
MENU POSITION [Default]
Select with↑or↓
then 
 to return
Menu 8-33
4. PressENTERto toggle between Yellow, Red and Blue.
8.11.2 Menu Position
How to change
1. Push the cursor key↑or↓to highlightOSD.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu...

8. Installation Mode
Available patterns
- Outline
-Hatch
- Color bars
- Multiburst
- Checker board
- Page Char
- Alpha numeric char
How to select an internal patterns?
1. Push the cursor key↑or↓to highlightInternal Patterns.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-36
2. PressENTERto select.
The internal patterns menu will be displayed.
INTERNAL...

9. Service Mode
9. SERVICE MODE
9.1 Built-up
Built-up
The service menu is built-up in two parts which are connected together with the ’more’ item. If the desired item is not in the list of
the displayed menu, select ’more’ with the cursor key and push ENTER to display the other items in the service menu.
9.2 Start up
Start up
1. Push the cursor key↑or↓to highlightService.
ADJUSTMENT MODE
Select a path from below :
RANDOM ACCESS
INSTALLATION
SERVICE
Select with↑or↓
then 
 to return
Menu 9-1
2....

9. Service Mode
The following items will be displayed:
• Type of projector: SLM R12+
• Software version
• Network module: yes
• Proj. address: To change the address of the projector, see Change Projector Address, page 114
Installation:
- front/ceiling
- front/table
- rear/ceiling
- rear/table
• Baud rate: transfer speed for communication with an IBM PC (or compatible) or MAC. The baud rate of the projector must be
the same as the baud rate of the connected computer. When there is a difference, consult...

9. Service Mode
The different levels are:
• owner
•user
• guest
Depending on your password level some password protected items are accessible and others not. The owner (which has the highest
level) can set up via the ’Access control list’ the accessibility of the different items. See ’Access Control List’.
Get access to the controller module
1. Power down the projector and disconnect the power cord from the wall outlet.
2. Loosen the indicate screws of the input box.
Image 9-1
Image 9-2
Access password...

9. Service Mode
6. Change the position of S2.
How to change the password ?
1. Push the cursor key↑or↓to highlightChange Password.
SERVICE
IDENTIFICATION
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJ. ADDRESS
SERIAL COMMUNICATION
NETWORK
LAMP
DIMMING
MORE...
Select with↑or↓
then 
 to return
Menu 9-6
2. PressENTERto display theChange Passwordmenu.
Note:Only possible when Owner.
CHANGE PASSWORD
Enter new password
OWNER 0000
USER 0000
GUEST 0000
ACCESS CONTROL LIST
Select with↑or↓
then 
Reprogram with↓,↑,←or→...

9. Service Mode
2. PressENTERto display the Change password menu.
Note:Only possible when Owner.
CHANGE PASSWORD
Enter new password
OWNER 0000
USER 0000
GUEST 0000
ACCESS CONTROL LIST
Select with↑or↓
then 
Reprogram with↓,↑,←or→
or numeric keys
 to confirm
 to return
Menu 9-9
3. Push the cursor key↑or↓to highlightAccess Control List.
4. PressENTERto display the Access Control List menu.
ACCESS CONTROL LIST
M
enuOUGEAdj modeYYYY
BARCO LOGOY---
Change addYY--
O=owner, U=user, G=Guest
E=everybody
Select...

9. Service Mode
9.5 Changing Language
Start up
1. Push the cursor key↑or↓to highlightChange Language.
SERVICE
IDENTIFICATION
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJ. ADDRESS
SERIAL COMMUNICATION
NETWORK
LAMP
DIMMING
MORE...
Select with↑or↓
then 
 to return
Menu 9-11
2. PressENTERto display theChange Languagemenu.
CHANGE LANGUAGE
ENGLISH
Select with↑or↓
then 
 to return
Menu 9-12
3. Push the cursor key↑or↓to highlight the desired language.
4. PressENTERto change the language.
Available languages:...

9. Service Mode
3. Push the cursor key↑or↓to highlightProjector address.
4. PressENTERto activate.
The first digit will be highlighted.
5. Reprogram the address with↑,↓,←,→keys
Use the↑or↓key to select a new value, use the←or→key to select a new digit.
Or,
use the numeric keys on the RCU to enter the new address.
The address must be between 0 and 9 when controlling the projector with the RCU or
between 0 and 255 when controlling the projector via RS232.
How to change the common address
1. Push the cursor...

9. Service Mode
9.7.1 Start Up of the Serial Communication
Start up
1. Push the cursor key↑or↓to highlightSerial communication.
SERVICE
IDENTIFICATION
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJ. ADDRESS
SERIAL COMMUNICATION
NETWORK
LAMP
DIMMING
MORE...
Select with↑or↓
then 
 to return
Menu 9-17
2. PressENTERto display the Serial Communication menu.
SERIAL COMMUNICATION
PROJECTOR ADDRESS 001
BAUDRATE [115200]
INTERFACE STANDARD [RS232]
RS422 TERMINATION [ON]
Select with↑or↓
then 
 to return
Menu 9-18...