Barco Slm R12+ Owners Manual

9. Service Mode
FIB
Formatter interface board
How to select?
1. Push the cursor key↑or↓to highlightI2C.
DIAGNOSIS
I2C
DMD
SMPS
LPS1
LPS2
LPS3
VOLTAGES
FANSPEED
Select with↑or↓
then 
 to return
Menu 9-40
2. PressENTERto select.
The I2C Diagnosis overview will be displayed.
If the indication behind the hex code is green, everything is ok.
If the indication is red, something is wrong with that indicated address.
I2C DIAGNOSIS
MOTOR DRIVER 1AH ###
LIGHT SENSOR 1CH ###
LPS 20H ###
SMPS 30H ###
FIB 34H ###
Red...

9. Service Mode
9.15.4 SMPS
How to select the overview?
1. Push the cursor key↑or↓to highlightSMPS.
DIAGNOSIS
I2C
DMD
SMPS
LPS1
LPS2
LPS3
VOLTAGES
FANSPEED
Select with↑or↓
then 
 to return
Menu 9-44
2. PressENTERto select.
The SMPS overview menu will be displayed.
SMPS
µC VERSION 03.01
EEPROM VERSION 03.00
Internal T. 26(45)C
NTC T. 38(80)C
Internal temp. OK
NTC OK
TILT SWITCH OK
MICRO SWITCH OK
LAMP TEMP OK
LPS MAINS OK
SMPS OUTPUT OK
 to return
Menu 9-45
9.15.5 LPS (lamp power supply)
How to select the...

9. Service Mode
9.15.6 Voltages
How to select the overview?
1. Push the cursor key↑or↓to highlightVoltages.
DIAGNOSIS
I2C
DMD
SMPS
LPS1
LPS2
LPS3
VOLTAGES
FANSPEED
Select with↑or↓
then 
 to return
Menu 9-48
2. PressENTERto select.
Thevoltageoverview window will be displayed.
VOLTAGES
FAN1 VOLTAGE 14V OK
FAN2 VOLTAGE 14V OK
FAN3 VOLTAGE 17V OK
15 VOLT 14V OK
30 VOLT 29V OK
12 VOLT 12V OK
5 VOLT 5.0V OK
3.3 VOLT 3.1V OK
 to return
Menu 9-49
9.16 Factory defaults
What is possible ?
The projector will set...

9. Service Mode
3. Are you sure to restore the factory defaults ?
If yes, press the cursor key↑or↓to highlightContinue.
A message will be displayed.
Factory defaults
Please wait
Remaining time:xsec
Menu 9-52
If no, press the cursor key↑or↓to highlightReturn.
Restoring the factory defaults can take a while. When finished, the projector will automatically reboot and
those factory settings will be loaded.
130R5976654 SLM R12+ 27/01/2005 

10. Programmable Function Keys
10. PROGRAMMABLE FUNCTION KEYS
10.1 Function Keys
What can be done with these keys?
The five function keys on top of an adapted remote control can be programmed as short cut keys (quick access) to almost any
adjustment menu.
How can a function key be programmed?
A function key can only be programmed when in the adjustment mode. Handle as follow :
1. Scroll through the menus until the desired menu is reached.
2. Press the desired function key for this menu during a few...

10. Programmable Function Keys
132R5976654 SLM R12+ 27/01/2005 

A. Standard Source set up Files
A. STANDARD SOURCE SET UP FILES
A.1 Table overview
Table overview
The following standard source files are pre-programmed in the projector.
Name1Resolu-
tion2Fvert
Hz
3
FHor
kHz
4
Fpix
MHz
5
Ptot6Pact7Ltot8Lact9
1600_48V1600x600i48,04062,500135,00021601600651600
1600_60V1600x120060,00075,000162,0002160160012501200
1600_65V1600x120065,00081,250175,5002160160012501200
1600_70V1600x120070,00087,500189,0002160160012501200
8514_A1024x384i43,47935,52244,90012641024409384...

A. Standard Source set up Files
Name1Resolu-
tion2Fvert
Hz
3
FHor
kHz
4
Fpix
MHz
5
Ptot6Pact7Ltot8Lact9
INTER_GR1184x88667,17061,79692,94115041184920886
MAC_2640x48066,66735,00030,240864640525480
MAC_3512x38460,14724,48015,667640512407384
MAC_4560_38460,14724,48017,234704560407384
MAC_5512x34260,15822,25916,670704512370342
MAC_6832x62474,54649,72257,2801152832667624
MAC_71024x76874,90760,15080,00013301024803768
MAC_LC640x48066,61934,97531,338896640525480
MAC_POR640x87074,99668,84657,280932640918870...

A. Standard Source set up Files
Name1Resolu-
tion2Fvert
Hz
3
FHor
kHz
4
Fpix
MHz
5
Ptot6Pact7Ltot8Lact9
SUNXGA771024x76877,06962,04084,37513601024805768
SUP_MAC1024x76860,00048,78063,99913121024813768
SVGA_56V800x60056,25035,15636,0001024800625600
SVGA_60V800x60060,31737,87940,0001056800628600
SVGA_72V800x60072,08448,08050,0031040800667600
SXGA+_11400x105059,94563,902107,8661688140010661050
SXGA+_21400x105083,85491,149171,3611880140010871050
VGA_72V640x48072,80037,85631,496832640520480...

A. Standard Source set up Files
136R5976654 SLM R12+ 27/01/2005