Barco Slm R12+ Owners Manual

9. Service Mode
9.7.3 Setting up the Interface Standard
Set up
The communication protocol for the communication between the projector and a computer can be set on RS232 or RS422. To set
up the desired protocol, handle as follow :
1. Push the cursor key↑or↓to highlightInterface Standard.
SERIAL COMMUNICATION
PROJECTOR ADDRESS 001
BAUDRATE [115200]
INTERFACE STANDARD [RS232]
RS422 TERMINATION [ON]
Select with↑or↓
then 
 to return
Menu 9-20
The actual interface standard will be displayed.
2. PressENTERto...

9. Service Mode
Set up the network configuration.
To set up the network configuration, follow the next procedure :
1. Push the cursor key↑or↓to highlightNetwork Configuration.
SERVICE
IDENTIFICATION
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJ. ADDRESS
SERIAL COMMUNICATION
NETWORK
LAMP
DIMMING
MORE...
Select with↑or↓
then 
 to return
Menu 9-22
2. PressENTERto display the network configuration menu.
NETWORK CONFIGURATION
DHCP [ON]
IP ADDRESS 158.150.160.200
SUBNET MASK 158.150.160.201
DEFAULT GATEWAY...

9. Service Mode
If a wrong value for an octet is entered, the following error message will be displayed to indicate where the error is located.
Example of message : Invalid octet. The maximum value is 255 for each octet !  .
ERROR
Invalid octet
the maximum value is
255 for each octet!
 to return.
Menu 9-25
9.9 Lamp
Lamp information light output switching
All information about the lamp is stored inside the lamp house and can be displayed via the projector software on the projection
screen. No information...

9. Service Mode
100
Clo value
Time [h]
Ligh
toutput [
%]
Image 9-6
Linking via the RS232 in/out
The constant light output of projectors in a chain (maximum 12 projectors) can be set to the same value by linking the projectors via
the RS232 connector.
To the RS232in of the first projector, a terminator must be connected (Z3498823). The out of the first must be connected to the in
of the next projector, etc.
All projectors must have a different projector address between 1 and 12.
All must have the same...

9. Service Mode
To slave 1Master Projector
Comm port
Comm 800 splitter
To slave 2To slave 3
To next Comm 800 splitter
To Switcher
To slave 4
Comm 800 splitter
To slave 5To slave 6
To slave 7 or to 
next Comm 800 splitte
r
To SwitcherImage 9-8
Principal diagram: Linked via Comm port
For more information about the use of the Comm 800 splitter, consult the Comm 800 splitter documentation (R5976819).
Which information is available
serial numberunique serial number of the lamp
typelamp type
run timetotal time...

9. Service Mode
The lamp menu will be displayed.
LAMP
Constant Light output [OFF]
Using [RS port]
Mode [NORMAL]
Serial number : R101111
Article number : R9840xxx
Run time : 10 hours
Remaining run time : 490
hours
Number of strikes : 10
Z_AXIS : 100
Select with↑or↓
then 
 to return.
Menu 9-27
How to switch the constant light output?
1. Push the cursor key↑or↓to highlightConstant Light Output.menu 9-27
2. PressENTERto toggle between [OFF], [SLAVE] and [MASTER].
[OFF] fixed power, no power adaptation....

9. Service Mode
2. PressENTERto select.
A dimming slider box appears on the screen.
3. Use the↑or↓keys to dim the lamp until the desired light output is reached.
9.11 BARCO Logo
What can be done?
The BARCO logo can be added to the image, in overlay or on a background, on any place on the screen.
How to add the BARCO logo or to change the setting?
1. Push the cursor key↑or↓to highlightBARCO logo.
SERVICE
BARCO LOGO
ADD INS
PRESET INPUT BALANCE
ADVANCED PROCESSING
DIAGNOSIS
FACTORY DEFAULTS
MORE...
Select...

9. Service Mode
Available Add Ins
CLO : When activated, the lamp option ‘Constant light output’ in the menu ‘Lamp’ becomes available.
Scenergix : When activated, soft edging becomes possible in the Random access adjustment mode.
How to activate an add-ins?
1. Push the cursor key↑or↓to highlightAdd-Ins.
SERVICE
BARCO LOGO
ADD INS
PRESET INPUT BALANCE
ADVANCED PROCESSING
DIAGNOSIS
FACTORY DEFAULTS
MORE...
Select with↑or↓
then 
 to return
Menu 9-31
The Add-Ins menu will be displayed.
ADD-INS
CLO [INACTIVE]...

9. Service Mode
Start Up
1. Push the cursor key↑or↓to highlightPreset Input Balance.
SERVICE
BARCO LOGO
ADD INS
PRESET INPUT BALANCE
ADVANCED PROCESSING
DIAGNOSIS
FACTORY DEFAULTS
MORE...
Select with↑or↓
then 
 to return
Menu 9-34
2. PressENTERto select.
The following warning will be displayed :
WARNING
PRESET INPUT BALANCE
is reserved to
qualified
service personnel
 to accept
 to return
Menu 9-35
Preset input balance is reserved to qualified service personnel. If you are not qualified, pressEXITto...

9. Service Mode
TheAdvanced Processingmenu will be displayed.
ADVANCED PROCESSING
MINIMUM DELAY [ON]
 to toggle
 to return
Menu 9-37
3. Select Minimum Delay and press ENTER to toggle between [ON] or [OFF].
9.15 Diagnosis
9.15.1 How to start up the Diagnosis?
What can be seen?
The diagnosis menu gives the possibility to select an overview of the I2C controlled IC’s and an overview of the working of the
formatter.
Start up
1. Push the cursor key↑or↓to highlightDiagnosis.
SERVICE
BARCO LOGO
ADD INS
PRESET...