Barco Rlm R6+ Performer Owners Manual

14. Installation menu
Image 14-15
14.8 Automatic startup
What can be done ?
The automatic startup allows immediate restart of the projector after a power failure (breakdown), i.e. without passing through the
standby state.
The projector restarts at power resume and recovers the previous settings (previous source,...).
This function can be disabled if undesired or inadequate for safety reasons,etc.
CAUTION:If the Automatic startup function is enabled one must be aware of the fact that it involves safety...

14. Installation menu
14.9 Security
What can be done ?
A security function is implemented in the projector that allows a protection against theft.
A PIN code allows the user to lock the projector in case of wrong code entry.
The PIN code must be entered at each start up (Power ON), entering three times a wrong number triggers a wait cycle of 15 minutes,
the second 3 wrong codes a wait cycle of 30 minutes, 1 hour, ...
The security mode can be enabled or disabled.
How to activate the security mode ?
1....

14. Installation menu
Security
Activating the security mode involves
the following things:
- The startup screen (identification window)
will contain a line withthe name of the
owner in it.
- You will be asked to enter a PIN code
every time the projector lost its power.
Are you sure you want to activate the 
Security mode
YESNO
Image 14-18
Security
Enter name of owner
e.g. Barco Educational Center
Image processing department
Brussels - Belgium
ACCEPTCANCEL
Image 14-19
Security
Enter your PIN:
Confirm your...

14. Installation menu
140R5976816 RLM R6+ PERFORMER 21/12/2005 

15. Service
15. SERVICE
Overview
• Version Table
• Lamps and Power supply
• Board Identification
• Diagnostics
• Formatter firmware
• Formatter reset
15.1 Version Table
What is possible ?
To get an overview of the different software and firmware version inside the projector.
How to get the version table
1. PressMENUto activate the menu bar. (image 15-1)
2. Press→to select theServiceitem.
3. Press↓to pull down the menu.
4. Use↑or↓to selectVersion table....
5. PressENTER.
An options dialog box opens....

15. Service
How to get the lamps and power supply overview ?
1. PressMENUto activate the menu bar. (image 15-3)
2. Press→to select theServiceitem.
3. Press↓to pull down the menu.
4. Use↑or↓to selectLamps and Power supply....
5. PressENTER.
An list dialog box opens. (image 15-4)
Image 15-3
Image 15-4
15.3 Board Identification
What is possible ?
To get an overview of the board article numbers inside the projector.
How to get an overview ?
1. PressMENUto activate the menu bar. (image 15-5)
2. Press→to...

15. Service
Image 15-5
Image 15-6
15.4 Diagnostics
Overview
• I²C Diagnostics
• Lamps and power supply
15.4.1
I²C Diagnostics
What can be done ?
The I2C bus allows the diagnostic of different hardware components
How to display the diagnostics menu ?
1. PressMENUto activate the menu bar.
2. Press→to select theServiceitem. (image 15-7)
3. Press↓to pull down theServicemenu.
4. Use↑or↓to selectDiagnostics.
5. Press→to pull down the menu.
6. Use↑or↓to selectI²C.
7. PressENTERto select I
2C.
A text box is...

15. Service
Image 15-7
I2C Diagnostics
Device Slave address
Lamp driver I2C Diagnostics
0x78
Lamp Eeprom 0xA0
Power Supply 0x30
I2C Mulitplexer 0xE0
Red Formatter 0x34
Green Formatter 0x36
Blue Formatter 0x38
Motor driver 0x1A
Image 15-8
15.4.2 Lamps and power supply
What can be done ?
This menu item gives an overview of the lamp and power supply errors.
How to display the overview menu ?
1. PressMENUto activate the menu bar.
2. Press→toselect theServiceitem. (image 15-9)
3. Press↓to pull down...

15. Service
Image 15-10
15.5 Formatter firmware
How to display ?
1. PressMENUto activate the menu bar. (image 15-11)
2. Press→to select theServiceitem.
3. Press↓to pull downthe menu.
4. Use↑or↓to selectFormatter firmware....
5. PressENTER.
An options dialog box opens. (image 15-12)
Image 15-11
Image 15-12
15.6 Formatter reset
What can be done ?
During start up it is possible that one or more colors do not start up correctly.
To solve this problem, the formatters will be restarted. During this process,...

15. Service
How to display ?
1. PressMENUto activate the menu bar. (image 15-13)
2. Press→to select theServiceitem.
3. Press↓to pull down the menu.
4. Use↑or↓to selectFormatter reset....
5. PressENTER.
An confirmation dialog box opens. (image 15-14)
Image 15-13
Image 15-14
146R5976816 RLM R6+ PERFORMER 21/12/2005