Barco Rlm R6+ Performer Owners Manual

9. Tools Menu
This can also be done by using the dedicated PiP Adjust key on the RCU
Image 9-20
PiP adjust in case of 2-by-2 layout
A Data1 window has the focus, new settings will only affect Data1 window
B Video1 window has the focus, new settings will only affect Video1 window
PiP adjust
1. PressMENUto activate the menu bar.
2. Press→to select theToolsitem. (image 9-21)
3. Press↓to pull down theToolsmenu.
4. Use↑or↓to selectPiP Adjust.
5. PressENTER.
The menu disappears.
6. PressENTERto move the focus...

9. Tools Menu
98R5976816 RLM R6+ PERFORMER 21/12/2005 

10. Signal menu
10. SIGNAL MENU
Overview
• Overview of the Signal menu
• Switching mode
• Output Frame rate
• Background
10.1 Overview of the Signal menu
Overview
• Switching mode
-Seamless
-Boxin
- Box out
- Shift in left
- Shift in right
- Shift in top
- Shift in bottom
- Vertical curtain open
- Vertical curtain close
- Horizontal curtain open
- Horizontal curtain close
- Fade in out
- Random
• Output frame rate
- Synchronous
-50Hz
-60HZ
• Background
-Blue
-Black
10.2 Switching mode
Switching from one...

10. Signal menu
Image 10-1
TheRandommode will select a new switching mode at each source switching i.e. there will never be 2 suc-
cessive source switchings with the same effect.
The Seamless switching mode is not used in theRandommode.
Note on Fade in/out
In some cases, depending on the sources to be switched, the fade in/out effect is impossible or may not occur.
100
R5976816 RLM R6+ PERFORMER 21/12/2005 

10. Signal menu
Image 10-2* Video may be Composite video/ S-Video / SDI
• dark arrow : fade in/out effect possible
• dotted arrow : undetermined case, fade in/out effect may take place or not
• striked out arrow : fade effect impossible
The switching effects are only possible in the full screen mode
10.3 Output Frame rate
What can be done ?
To avoid transition effects when switching from a source with a frame rate of 50 Hz to a source with frame rate of 60 Hz or vice versa,
set the output frame rate to...

10. Signal menu
4. Use↑or↓to selectOutput frame rate.
5. Press→to pull down the menu.
6. Use↑or↓to select the desired frame rate.
The following choices are possible:
- synchronous : the output follows the input frame rate.
- 50 Hz : output is always displayed with a frame rate of 50 Hz
- 60 Hz : output is always displayed with a frame rate of 60 Hz
7. PressENTER.
Image 10-3
10.4 Background
Purpose
If there is no signal connected to the projector, the background will be a black or a blue screen depending...

11. Lamps Menu
11. LAMPS MENU
Overview
• Overview of the Lamps menu
• Runtimes
• Mode
• Economic ON/OFF
• Runtime warning
11.1 Overview of the Lamps menu
Overview
• Runtimes...
• Mode
- Single...
- Dual...
• Economic
• Runtime warning
11.2 Runtimes
How to display the lamp runtimes ?
1. PressMENUto activate the menu bar.
2. Press→to select theLampitem. (image 11-1)
3. Press↓to pull down theLampsmenu.
4. Use↑or↓to selectRuntimes.
5. PressENTER.
A text box is displayed. (image 11-2)
Image 11-1
Runtime
Lamp...

11. Lamps Menu
11.3 Mode
Single lamp mode
The projector will always switch to the lamp with the shortest runtime when the difference between the runtimes of lamp 1 and lamp
2 reaches100 hours, switching from one lamp to another happens only at switching on of the projector and not during operation.
When the lamp fails or reaches its maximum runtime the projector switches automatically to the other lamp without interrupting the
projection. The failure is logged and the lamp will never be initialized in...

11. Lamps Menu
Image 11-4
When switching from the dual mode to the single mode the lamp with the longest runtime is switched off.
If the runtimes are equal (if the projector has always been operated in dual mode) then lamp 1 is switched out.
When switching to single mode, returning to the dual mode will not be possible in the first 60 seconds,Dual
in the menu is greyed out and LED3 is flickering, thereby preventing hot restrike which may damage the lamp.
11.4 Economic ON/OFF
What can be done?
The lamp...

11. Lamps Menu
4. Use↑or↓to selectRuntime warning.
5. PressENTERto confirm.
A dialog box is displayed. (image 11-7)
6. PressENTERto activate the input field.
7. Use←or→to change the runtime warning setting.
Or,
enter the desired value with the digit keys on the remote control.
8. PressBackto return.
Image 11-6
Lamp runtime warning
hrs before end of lamp lifetime
30
Image 11-7
WARNING:Lamp replacement should be done by a Barco authorized technician.
106R5976816 RLM R6+ PERFORMER 21/12/2005