Barco Projector Toolset For Hdx Series Reference Guide

6. Configurator, General projector settings
3. To change the year, date and time, click on the corresponding up down control of the spin box until the
desired value is reached (4).
4. Click onSetto set the clock (6).
Use the refresh button the refresh the clock values (5).
Image 6-23
6.9 Maintenance
Overview
• Reset to factory defaults
• Reset electronics
6.9.1 Reset to factory defaults
What can be done?
All settings of the projector areset to the original factory settings with the exception of the IP...

6. Configurator, General projector settings
The following items are normally exclude during a reset operation:
-IPsettings
- Serial communication settings
- DMX settings
3. Click on the buttonReset nownext toReset to factory defaults(c).
4. ClickClose.
Image 6-24
Restore factory defaults
6.9.2 Reset electronics
How to reset
1. Click onMaintenance. (image 6-25, image 6-26)
The Maintenance dialog box is displayed.
2. Click on the buttonReset nownext toReset electronics.
3. ClickClose.
Image 6-25
Reset...

6. Configurator, General projector settings
Image 6-26
Reset electronics
R5905073 PROJECTOR TOOLSET 07/06/201189 

6. Configurator, General projector settings
90R5905073 PROJECTOR TOOLSET 07/06/2011 

7. Configurator, Projector alignment settings
7. CONFIGURATOR, PROJECTOR
ALIGNMENT SETTINGS
Overview
• Lens control
• Test patterns
• Gamma adjustment
• Individual color selection
• Blanking adjustment
•ScenergiX
7.1 Lens control
Overview
•Lensshift
• Lens mid position
• Lens zoom
• Lens focus
7.1.1 Lens shift
What can be done?
When the lenses are motorized, it is possible to adjust these lenses via the Projector Toolset. The images
can be shifted horizontally and vertically.
Image 7-1
Lens shift
How to...

7. Configurator, Projector alignment settings
Image 7-2
How to bring to mid position
1. Click on the Center button between the shift buttons.
7.1.3 Lens zoom
What can be done?
When the lenses are motorized, it is possible to zoom these lenses via the Projector Toolset.
Image 7-3
How to zoom
1. Click on the up or down arrow button in the zoom pane.
7.1.4 Lens focus
What can be done?
When the lenses are motorized, it is possible to focus these lenses via the Projector Toolset.
Image 7-4
How to focus
1....

7. Configurator, Projector alignment settings
Click until the correct focus is obtained.
7.2 Test patterns
What can be done?
A predefined pattern can be set immediately on the projection screen and cleared again. This can be
done via short cuts or via other internal patterns. Extra settings for the internal patterns can be set.
To select a short cut pattern
1. Click on one of the predefined buttons. (image 7-5)
The selected pattern is displayed by the projector when the lamp is on and the shutter is open...

7. Configurator, Projector alignment settings
Image 7-6
7.3 Gamma adjustment
About Gamma
Gamma is an image quality enhancement function that offers a richer image by brightening the already
darker portions of the image without altering the brightness of the brighter portions (contrast feeling en-
hanced).
Image 7-7
Gamma adjustment
Adjusting via dragging
1. Click on the slider bar of the gamma adjustment and hold down the mouse button.
2. Move the slider until the desired value is reached.
The value in...

7. Configurator, Projector alignment settings
Adjusting via the up down controls
1. Click on the up down control of the spin box of the gamma adjustment until the desired value is reached.
The value in the inputfield change accordingly.
Adjusting via the inputfield
1. Click inside the inputfield of the spin box of the gamma adjustment.
2. Select the actual value and enter a new value with the keyboard.
7.4 Individual color selection
What can be done?...

7. Configurator, Projector alignment settings
Which blanking adjustments are available ?
• top blanking
• bottom blanking
• left blanking
• right blanking
Image 7-9
Blanking
A Top blanking
B Bottom blanking
C Left blanking
D Right blanking
How to adjust a side blanking
1. Click on the up down control of the spin box of the desired blanking until the chosen blanking is correctly
set up.
Or,
click in the inputfield of the spin box of the desired blanking and enter the desired blanking value.
(image 7-10)...