Barco Projector Toolset For Hdx Series Reference Guide

7. Configurator, Projector alignment settings
Image 7-10
Blanking adjustment
Use Reset to set all blanking settings to zero.
7.6 ScenergiX
7.6.1 Introduction
Why ScenergiX ?
When working in a multichannel setup the Projector Toolset and its Soft Edge possibilities enable an image
blending that gives the appearance of a single view, thus achieving realistic immersion for the majority of
wide screen applications.
ScenergiX is limited to half the resolution of the projector.
Image 7-11
Why Soft Edge?...

7. Configurator, Projector alignment settings
What is the Basic Principal of ScenergiX ?
The principle of edge blending is achieved by linear modulation of the light output in the overlap zone so
that the light output in that zone equals the light output of the rest of the image.
Adjustable overlapping area
50% 100%50% 100%
image 2 image 1
image 2 image 1
Light output per image
Total composite light output
Image 7-12
ScenergiX Basic Principle
7.6.2 Preparations
ScenergiX Preparations
To ensure proper...

7. Configurator, Projector alignment settings
Image 7-13
Enable - disable ScenergiX
R5905073 PROJECTOR TOOLSET 07/06/201199 

7. Configurator, Projector alignment settings
7.6.4 ScenergiX overlap zone (horizontal ScenergiX)
Definitions
Image 7-14
ScenergiX set up
Overlap : number of pixels that overlap
Horizontal resolution of 1 projector : 1024 for Graphics versions, 1280 for Reality versions, 1400 for SXGA
projectors.
Total horizontal screen resolution : [(horizontal resolution of 1 projector) x 2] minus overlap.
Horizontal Resolution source : number of active pixels of the source.
Adjustment of Active pixels of thefirst...

7. Configurator, Projector alignment settings
Horz. start projector 2 = Horz. start projector 1 + (1600 – 841)
7.6.5 ScenergiX overlap zone (vertical ScenergiX)
Definitions
Image 7-15
Scenergix overlap zone vertical
Overlap : number of pixels that overlap
Vertical resolution of 1 projector : 768 for Graphics versions, 1024 for Reality versions, 1050 for SXGA
projectors.
Total vertical screen resolution : [(Vertical resolution of 1 projector) x 2] minus (overlap)
Vertical Resolution source : number of...

7. Configurator, Projector alignment settings
7.6.6 ScenergiX size adjustment (white level adjustment)
What can be done with the manipulations pane?
The Top, bottom, left or right item set the blending zone.
Image 7-16
Width selection
How to set a blending zone
1. Click on the up down control of the spin box of the selected blending zone and adjust until the desired
zone is reached (image 7-17)
Or,
click in the inputfield of the spin box of the selected blending zone and enter the desired value.
The...

7. Configurator, Projector alignment settings
Image 7-17
ScenergiX size adjustment
Use Reset to set all overlap zones back to zero (0).
7.6.7 Adjusting the black level of the images
Why black level adjustment
For dark images, the overlap zone will be brighter then the rest of the images. Typically for DLP projectors,
next to the overlap zone, a brighter area is recognized. This area is known as a DLP leakage area. This
area must also be exclude for the black level adjustment. Therefore we can rise the...

7. Configurator, Projector alignment settings
Image 7-18
DLP Leakage area set up
How to set the leakage area width
1. Click on the up down control of the spin box of the selected leakage zone and adjust until the desired
zone is reached (leakage area is covered)
Or,
click in the inputfield of the spin box of the selected leakage zone and enter the desired value. (im-
age 7-19)
WhenShow alignment linesis checked, the corresponding green line on the screen will move in the
same direction. The leakage area...

7. Configurator, Projector alignment settings
Image 7-19
Leakage area adjustment
R5905073 PROJECTOR TOOLSET 07/06/2011105 

7. Configurator, Projector alignment settings
Image 7-20
DLP leakage area
1 Overlap area
2 DLP Leakage area
How to adjust the black level
1. Click on the slider an move this slider to the desired position. (image 7-21)
Or,
click on the up down control of the spin box of the selected color until the desired value is reached.
Or,
click in the inputfield of the spin box of the selected color and enter the desired value.
Adjust the black level of area A until the black level of area A, B and C are equal....