Home > Barco > Projector > Barco Projector Cineversum 80 Quickstart Manual

Barco Projector Cineversum 80 Quickstart Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Barco Projector Cineversum 80 Quickstart Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 183 Barco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							7. Connections
    Input modeSignal format (1), (2), (3) or (4) selectable on the GUI menu
    Bandwidth500 MHz RGB Analog Bandwidth convertor
    Signal supportSupports signals up to 205 MHz Pixel clock (1600 x 1200 @ 75 Hz)
    Sync DetectionAutomatic Sync detection for: RGBHV, RGBS and RGsB.
    Sync PolarityAutomatic Sync Polarity detection
    Input signal level
    RGsB Input ModeRGB signal: 0.7Vpp
    Composite Video Sync on G: 1Vpp
    RGBS Input ModeRGB signal: 0.7Vpp
    Composite Video Sync on H: 1Vpp
    RGB/HV Input ModeRGB signal: 0.7Vpp
    Hs Sync signal: 0.7Vpp
    Vs Sync signal: 0.7Vpp
    Component Input ModeY+Synchro: 1.0Vpp
    Pr
    Pb
    SDI Input
    Image 7-23
    Features- Loop through SDI Input (SDI in/SDI out)
    - For DVD players and other Video equipment with SDI out.
    HD SDI Input
    Image 7-24
    R5976468 CINE VERSUM SYSTEM 0311200357 
    						
    							7. Connections
    Features- Loop through HD-SDI Input (HD-SDI in/HD-SDI out)
    - For HD-DVD players and other HD Video equipment with HD-SDI out.
    Digital Visual Interface Input (DVI)
    DVI: Digital Visual Interface is a display interface developed in repose to the proliferation of digital flat panels
    displays. It uses a high speed serial interface with TMDS (Transition Minimized differential signalling) to send
    data to the display. DVI can be single or dual link.
    Image 7-25
    DVI input module
    with DVI-D type
    connector
    Image 7-26
    1RX2-7SDA_PC13TMDS DATA 3-19RX0 Shield
    2RX2+8nc14+5V Host20TMDS DATA 5-
    3RX2 Shield9RX1-15GND21TMDS DATA 5+
    4TMDS DATA 4-10RX1+16Hot Plug Detect22TMDS Clock Shield
    5TMDS DATA 4+11RX1 Shield17RX0-23RXC+
    6SCL_PC12TMDS DATA 3-18RX0+24RXC-
    7.4.2 Installation of an Input module
    How to install an Input module
    1. Has the new input module to be inserted in a free slot?
    If yes, go to step 2
    If no, go to step 3
    2. Take away the dummy plate by removing the two securing screws (A) and continue with step 5. (image 7-27)
    3. Unlock the module by loosening the rod screws (A). (image 7-28)
    4. Carefully pull out the module (image 7-28).
    5. Match the module plug with the slot connector and push the plug into the connector. (image 7-29)
    6. Secure the module by tightening the rod screws (A)(image 7-29).
    58
    R5976468 CINE VERSUM SYSTEM 03112003 
    						
    							7. Connections
    Image 7-27
    Image 7-28
    Image 7-29
    R5976468 CINE VERSUM SYSTEM 0311200359 
    						
    							7. Connections
    60R5976468 CINE VERSUM SYSTEM 03112003 
    						
    							8. Operating the Remote Control
    8. OPERATING THE REMOTE CONTROL
    Overview
    • Battery Insertion in the Remote Control
    • Operating the Remote Control
    • Address setting for the Remote Control
    8.1 Battery Insertion in the Remote Control
    – Insert batteries so that the plus (+) and minus (-) sides are aligned according to the markings in the battery
    case.
    – Do not mix new batteries with used ones.
    – The voltage of batteries may differ even if they are the same shape. Please do not mix different kinds of
    batteries.
    – When not using the remote control unit for a long period of time (1 month of more), remove the batteries
    from the remote control unit to prevent leaking of battery fluid. If battery liquid has leaked, thoroughly wipe
    the inside of the case until all liquid is removed, an then insert new batteries.
    - Do not charge, short, disassemble or throw the provided batteries in a fire.
    When disposing of used batteries, please comply with governmental regulations or environmental public in-
    struction’s rules that apply in your country.
    Where to find the batteries
    The batteries are not placed in the remote control to avoid remote control operation in its package, resulting in a shorter battery life
    time.
    The batteries are packed separately and added to the package of the remote control.
    How to install the batteries
    1. Push the cover tab (A) with the fingernail a little backwards and pull upwards the cover top (B). (image 8-1)
    2. Slide the cover forwards to remove. (image 8-2)
    3. Push the battery body towards the spring and lift it up to remove. (image 8-3)
    4. Insert two AA size batteries, making sure the polarities match the + and – marks inside the battery compartment (image 8-3).
    5. Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until it clicks in place
    (image 8-3).
    Image 8-1
    Battery cover unlock
    Image 8-2
    Battery cover removal
    R5976468 CINE VERSUM SYSTEM 0311200361 
    						
    							8. Operating the Remote Control
    Image 8-3
    Battery removal
    8.2 Operating the Remote Control
    Remote Control operation
    This remote control includes a battery powered infrared transmitter which allows the user to control the Cine VERSUM Master re-
    motely via its own built-in infrared receiver or via the infrared receivers built-in in the linked displays.
    If backlight and RC operation indicator lights up too long or continuously, batteries need to be replaced.
    F1F2F3
    F4
    F5
    ADJ EXIT
    ENT ER
    PA USE
    PHAS E TEXT
    S HARP N
    TI N T
    COLOR
    BRIGHTN
    CONTR
    TRE BLE BALANC E
    BASS V OL
    90
    78
    56
    34
    12
    45°45°
    Cine VERSUM 50Cine VERSUM 80
    Cine VERSUM 120
    Cine VERSUM Master
    Remote Control
    Image 8-4
    Display Infra Red reception
    When operating the remote control unit, point it at the remote sensor, located on the front side of the modules. The remote control
    unit is operable up to 9 m from the unit and within a 45 angle on each side of the sensor.
    The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal
    may differ due to the screen material.
    When a key on the remote control is pressed, backlight is activatedautomatically. That allows the user to operate the remote control
    in a dark room. Backlight is turned off automatically a few seconds after the last key activation.
    62
    R5976468 CINE VERSUM SYSTEM 03112003 
    						
    							8. Operating the Remote Control
    Remote control operation’s difficulties
    • The remote control unit may not operate if there are objects placed between it and the display.
    • Operational distances will gradually become shorter as the batteries begin to wear out, replace weak batteries with new ones
    as soon as possible.
    • Depending on the installation surroundings, this unit’s remote control may be influenced by the infrared rays discharged from
    the plasma display, hampering reception of its rays or limiting its operational distance. The strength of infrared rays discharged
    from the screen will differ according to the picture displayed.
    8.3 Address setting for the Remote Control
    How to set the Remote Control address
    1. Point the Remote Control to the module you desire to know the address and press the address key (recessed key).
    On-screen and in the graphical display appears the number of the address. Now proceed to program the address in the Remote
    Control.
    2. Again, press the ADDRESS key on the Remote Control. (image 8-5)
    3. Press the digit key, corresponding with the desired address (between 0 and 9), WITHIN 5 SECONDS after the key has been
    pressed. (image 8-6)
    The commands from the Remote Control are sent with the stored address.
    Image 8-5
    Address key
    Image 8-6
    Digit keys
    R5976468 CINE VERSUM SYSTEM 0311200363 
    						
    							8. Operating the Remote Control
    64R5976468 CINE VERSUM SYSTEM 03112003 
    						
    							9. Points of Similarity between Graphical display and On Screen Menus
    9. POINTS OF SIMILARITY BETWEEN GRAPHICAL
    DISPLAY AND ON SCREEN MENUS
    9.1 Explanation about differences in menu displays
    Purpose
    The different adjustment items are structured in main and sub menus. The way of showing the menus is different between the Cine
    VERSUM Master and the linked displays, but the subject matter of the menus is similar. Below a summary of the most important
    differences:
    Graphical display on Cine VERSUM Master
    On the Cine VERSUM Master a 4-line graphical display is built-in, with the result that only 4 items of a menu can be displayed.
    Rotating the selection wheel allows to scroll through the items, whereas pressing it, confirms the selection.
    CineVERSUM
    CineVERSUM
     
    >To enter the menu
      Press the button
      or use the RC
      -----------
    Graphical Display
    on Cine VERSUM Master
    CineVERSUM 
    7 xga75_gs.c03>To enter the menu
      Press the button
      or use the RC
      -----------
    Start up  menu
    File of the source included in the display
    Started up  menu
    Image 9-1
    Image 9-2
    Indication of the selected item
    The selected items on the graphical display are pointed with an arrow whereas the selected ones on the on-screen are highlighted.
    R5976468 CINE VERSUM SYSTEM 03112003
    65 
    						
    							9. Points of Similarity between Graphical display and On Screen Menus
    CineVERSUM
    7 xga75_gs.c03  Image settings
      Advanced Settings
    >Installation
      Service
      1 NO MODULE
      2 NO MODULE
      3 VIDEO [VIDEO]
      4 NO MODULE
      5 NO MODULE
      6 NO MODULE
      7 RGB -YUV [RGB]
      8 NO MODULE
      Shutdown
    Back
    Graphical Display
    on Cine VERSUM MasterOn Screen Display
    CV50, CV80 and CV120
    Main  menuMain  menu
        Cine VERSUM
    Image settings
    Advanced Settings
    Installation
    Service
    1 NO MODULE
    2 NO MODULE
    3 VIDEO [VIDEO]
    4 NO MODULE
    5 NO MODULE
    6 NO MODULE
    7 RGB -YUV [RGB]
    8 NO MODULE
    Shutdown
    Back
    Image 9-3
    Scrolling through the on-screen menus (Remote Control)
    Scrolling through the on screen menus happens with the up and down cursor keys on the Remote Control. Pressing the ENTER
    key confirms of the selection.
    Image 9-4
    Location of the menu or sub menu title
    Title of a menu or sub menu is put on top of the on screen menu and in the left top corner on the graphical display.
    66
    R5976468 CINE VERSUM SYSTEM 03112003 
    						
    All Barco manuals Comments (0)

    Related Manuals for Barco Projector Cineversum 80 Quickstart Manual