Barco Projector Cineversum 80 Quickstart Manual
Have a look at the manual Barco Projector Cineversum 80 Quickstart Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 183 Barco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
13. Projection Stop (Standby or Economic Standby mode) After the power down time, the standby LED on the Cine VERSUM 80 stays blinking on a beat of 0.3s on, 0.3s off for approximately 1 minute, named the cool down time. A new start up command will be executed after the cool down period only. R5976468 CINE VERSUM SYSTEM 0311200387
13. Projection Stop (Standby or Economic Standby mode) 88R5976468 CINE VERSUM SYSTEM 03112003
14. Switching linked displays To and Out Standby 14. SWITCHING LINKED DISPLAYS TO AND OUT STANDBY Overview • Switching by means of the Cine VERSUM Master • Direct Switching of the Linked Display 14.1 Switching by means of the Cine VERSUM Master Overview • Switching In/Out Standby using the Jog Dial • Switching In/Out Standby using the Remote Control 14.1.1 Switching In/Out Standby using the Jog Dial How to switch one or more displays To or Out standby mode 1. From the startup menu on the graphical display, press the jog dial to enter the main menu. (menu 14-1) 2. Scroll through the menu items until item INSTALLATION is pointed (menu 14-1). 3. Press the jog dial to confirm. The INSTALLATION menu will open showing the available installation items. (menu 14-2) 4. Scroll through the menu items until item DISPLAY LIST is pointed (menu 14-2). 5. Press the jog dial to confirm. The Display list menu opens showing the status of the linked displays, ON (operation), Standby or No display found (Display not powered up). The name of the linked displays in the display list menu below are numbered 1, 2 up to 6 as example. Notice that each display in the chain can be renamed. (menu 14-3) 6. Select the display , whose status you want to change, by rotating the jog dial, e.g. Display 2 with status ON (menu 14-3). 7. Press the jog dial to confirm. The Display settings menu opens showing the display setting items for that specific display. (menu 14-4) 8. Scroll through the menu items until item SWITCH OFF is pointed (menu 14-4). 9. Press the jog dial to confirm. The selected display switches to the standby mode preceded bya message. Finally, the status of the Display 2 will change to ’Standby’. (menu 14-5) CineVERSUM Image Settings Advanced settings >Installation Service 1 NO MODULE 2 NO MODULE 3 VIDEO [VIDEO] 4 NO MODULE 5 NO MODULE 6 NO MODULE 7 RGB-YUV [RGB] 8 NO MODULE Shutdown 7 xga75_gs.c03 Back Menu 14-1 Install Input slots File Service >Display List Internal Pattern When no signal Source Transition OSD Configuration Language Keystone Global Keystone:Yes Default Input Balance 7 xga75_gs.c03 Back Menu 14-2 Display List >2 CV50 1 On 3 CV50 2 Stdby 4 CV80 1 On 5 CV120 1 Stdby 6 CV80 2 On 7 xga75_gs.c03 Back Menu 14-3 Display Settings >Switch OFF Display Info Rename IR Address Update Soft CW Index Orientation Proj_mode 7 xga75_gs.c03 Back Menu 14-4 R5976468 CINE VERSUM SYSTEM 0311200389
14. Switching linked displays To and Out Standby Message Command sent to display _______________________________ _______________________________ _______________________________ Menu 14-5 Recap If the status of a display is On, via the display settings menu the display can be switched into the standby mode. If the status of a display is Standby, then the display can be switched to the operation mode. 14.1.2 Switching In/Out Standby using the Remote Control Make sure the Remote Control suits the address of the Cine VERSUM Master or uses the common address. How to switch one or more displays To or Out standby mode 1. Press theADJorENTERkey on the remote control to display the main menu on the screen. (menu 14-6) 2. Using the↑and↓arrow keys, scroll through the menu items until item ’Installation’ is highlighted (menu 14-6). 3. Press ENTER key to confirm. The installation menu opens, showing the different installation items. (menu 14-7) 4. Using the↑and↓arrow keys, scroll through the menu items untilitem ’Display list’ is highlighted (menu 14-7). The Display list menu opens, showing the linked displays. (menu 14-8) 5. Using the↑and↓arrow keys, select the display , whose status you want to change, e.g. Display 2 with status ON (menu 14-8). 6. PressENTERto confirm. The Display settings menu opens showing the display setting items for that specific display. (menu 14-9) 7. Scroll through the menu items, using the↑and↓arrow keys, until item Switch OFF is highlighted (menu 14-9). 8. PressENTERto confirm. The selected display switches to the standby mode preceded bya message. Finally, the status of the Display 2 will change to ’Standby’. (menu 14-10) Cine VERSUM System Image Settings Advanced Settings Installation Service 1 NO MODULE 2 NO MODULE 3 VIDEO [VIDEO] 4 NO MODULE 5 NO MODULE 6 NO MODULE 7 RGB-YUV [RGB] 8 NO MODULE Shutdown Back Menu 14-6 Installation Input slots File service Display list Internal pattern When no signal Source transition OSD Configuration Language Keystone Global keystone: Yes Output: [Largest] Default input balance Back Menu 14-7 Display List 2CV50 1:On 3 CV50 2: Off (Stdby) 4CV80 1:On 5 CV120 1: Off (Stdby) 6CV80 2:On Back Menu 14-8 Display settings Switch OFF Display Info Rename Update Software IR address: 9 CW Index Orientation Projector_mode Back Menu 14-9 90R5976468 CINE VERSUM SYSTEM 03112003
14. Switching linked displays To and Out Standby Message Command sent to display Menu 14-10 Recap If the status of a display is On, via the display settings menu the display can be switched into the standby mode. If the status of a display is Standby, then the display can be switched to the operation mode. For a display with status ’standby’, counteracting these status can be made using the jog dial on the Cine VERSUM Master or via the on-screen of an active display. 14.2 Direct Switching of the Linked Display 14.2.1 Switching a specific display In/Out standby Make sure the Remote Control suits the address of the display you desire to switch In or Out standby. How to switch one or more displays To or Out standby mode 1. Program the Remote Control with the address of the display you desire to switch In or Out standby (Module Address Read out/Change, page 93). 2. Point the Remote Control to the respective display. 3. Press a few seconds the standby key on the Remote Control. (image 14-1) The respective display switches into the standby mode. 4. Press a few seconds the standby key on the Remote Control again to restart operation. Image 14-1 Standby key R5976468 CINE VERSUM SYSTEM 0311200391
14. Switching linked displays To and Out Standby 92R5976468 CINE VERSUM SYSTEM 03112003
15. Module Address Read out/Change 15. MODULE ADDRESS READ OUT/CHANGE 15.1 Default address of the Modules Introduction To allow separate remote access to the different modules, an individual address has to be stored in each module. Overview default address modules Each module leaves the factory with a default address: ModuleAddress Cine VERSUM Master1 Cine VERSUM 809 Cine VERSUM 509 Cine VERSUM 1209 15.2 Reading out/Changing the stored addresses Overview • Reading out the stored address • Changing the stored addresses 15.2.1 Reading out the stored address Reading out the stored address of a module can be done using the address key on the Remote Control or via the Display settings menu. Reading out the stored address using the Remote Control (inclusive Cine VERSUM Master) 1. Point the front of the Remote Control to the IR Receiver of the module you desire to read out the stored address. 2. Press the address key (accessible with the top of a pencil)(On InfraRed Remote Control, page 30). A message, indicating the address number, appears as on screenmessage on the active display and also on the graphical display of the Cine VERSUM Master. The messages below belong to the Cine VERSUM Master. When pointing the displays, similar messages are generated maybe with another address. (menu 15-1) MESSAGEIR Address: 1 Menu 15-1 Message >IR Address: 1 7 xga75_gs.c03 _________ Menu 15-2 R5976468 CINE VERSUM SYSTEM 0311200393
15. Module Address Read out/Change Reading out the stored address using Display setting menu (exclusive Cine VERSUM Master) 1. Using the jog dial on the Cine VERSUM Master or the Remote control keys, successively selects Main menu, Installation and Display list. The display list (On screen,menu 15-4; Graphical display, menu 15-3) sums up the linked displays. The display name is preceded by its address number. The address number can also be find in the display settings menu of the respective display (continue with step 2). 2. Scroll through the display list until the display you desire to read out the address is highlighted (on screen) (menu 15-4) or pointed (graphical display) (menu 15-3). 3. Press jog dial on Cine VERSUM Master or pressENTERon Remote Control to confirm. The display settings of the selected display appear in the on screen menu (menu 15-6) and in the graphical display (menu 15-5), inclusive the IR address number. Display List >2 CV50 1 On 3 CV50 2 Stdby 4 CV80 1 On 5 CV120 1 Stdby 6 CV80 2 On 7 xga75_gs.c03 Back Menu 15-3 Display List 2CV50 1:On 3 CV50 2: Off (Stdby) 4CV80 1:On 5 CV120 1: Off (Stdby) 6CV80 2:On Back Menu 15-4 Display Settings Switch OFF Display Info Rename >IR Address: 9 Update Soft CW Index Orientation Proj_mode 7 xga75_gs.c03 Back Menu 15-5 Display settings Switch OFF Display Info Rename Update Software IR address: 9 CW Index Orientation Projector_mode Back Menu 15-6 Reading out the stored address Cine VERSUM Master using Service menu 1. Enter the GUI menu by pressing the jog dial on the Master or by pressing theENTERkey on the Remote Control. The main menu appears on-screen and in the graphical display on the Master. (menu 15-7) 2. Select item SERVICE by rotating the jog dial on the Master or by pressing the↑and↓key on the Remote Control. The service menu opens including the item indicating the IR address of the Cine VERSUM Master. (menu 15-8) Cine VERSUM System Image Settings Advanced Settings Installation Service 1 NO MODULE 2 NO MODULE 3 VIDEO [VIDEO] 4 NO MODULE 5 NO MODULE 6 NO MODULE 7 RGB-YUV [RGB] 8 NO MODULE Shutdown Back Menu 15-7 Service Identification Password IR Address 001 Common Address 000 Serial Communication I2C Diagnosis Back Menu 15-8 15.2.2 Changing the stored addresses Example of address setting To be able to control separately the displays by means of the Remote Control (e.g. operation and standby mode), an unique address has to be stored for each display separately. 94 R5976468 CINE VERSUM SYSTEM 03112003
15. Module Address Read out/Change Image 15-1 Example of address set up Changing the stored address of a linked display 1. Successively scroll throughthe menus Main (Cine VERSUM System), Installation, Display list. 2. Select in the display list the display you desire to change the address. 3. Press the jog dial or pressENTERto confirm. The display settings menu for that specific display appears on the screen and on the graphical display. 4. Scroll through the display setting items, using the jog dial or up/down arrow keys on the Remote Control and select item IR address 001. 5. Press the jog dial or pressENTERto confirm. A text box appears on the screen (menu 15-9) and in the graphical display (menu 15-10) requesting to enter a new 3 digit address value. 6. Enter a 3 digit number, from 000 to 256, using the number keys on the RCU. Note:As the Remote Control can remote addresses from 000 to 009 only, it is recommended to use this range of addresses. IR Address Enter New Value 001 Menu 15-9 IR Address >Enter New Value 001 7 xga75_gs.c03 _________ Menu 15-10 R5976468 CINE VERSUM SYSTEM 0311200395
15. Module Address Read out/Change Changing the stored address of the Cine VERSUM Master 1. Successively scroll through the menus Main (Cine VERSUM System), Service. 2. Select in the Service list item IR Address 001 3. Press the jog dial or pressENTERto confirm. A text box appears on the screen (menu 15-11) and in the graphical display (menu 15-12) requesting to enter a new 3 digit address value. 4. Enter a 3 digit number, from 000 to 256, using the number keys on the RCU. Note:As the Remote Control can remote addresses from 000 to 009 only, it is recommended to use this range of addresses. IR Address Enter New Value 001 Menu 15-11 IR Address >Enter New Value 001 7 xga75_gs.c03 _________ Menu 15-12 96R5976468 CINE VERSUM SYSTEM 03112003