Home > Barco > Projector > Barco Projector Cineversum 80 Quickstart Manual

Barco Projector Cineversum 80 Quickstart Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Barco Projector Cineversum 80 Quickstart Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 183 Barco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							19. Picture in Picture (PIP)
    • F1-F2-F4 and F5: changing the place of the PIP window in the projected image.
    Image 19-3
    Position of the PIP window
    • F1-F2-F4 and F5: enlarging the PIP window when pressed a second time.
    Image 19-4
    PIP window enlarged
    A Normal PIP window
    B Enlarged PIP window
    • F3: swapping the main source and the PIP source.
    Image 19-5
    Image swapping
    R5976468 CINE VERSUM SYSTEM 03112003137 
    						
    							19. Picture in Picture (PIP)
    138R5976468 CINE VERSUM SYSTEM 03112003 
    						
    							20. Cine VERSUM Master Settings & Info
    20. CINE VERSUM MASTER SETTINGS & INFO
    Overview
    • Service Menu
    • Cine VERSUM Master Identification
    • Cine VERSUM Master Password
    • CineVERSUMMasterAddress
    Entering the Installation as well as the Service menu can be password protected. If this should be the case,
    trying to enter both menus is preceded by a pop up menu, requesting to enter password.
    20.1 Service Menu
    How to enter the service menu
    1. Select the INSTALLATION menu (see Loading a File, page 97).
    2. Select itemSERVICEby rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
    3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    The sub menu SERVICE appears on-screen and in the graphical display, including a list of available settings and info, specific
    for the Cine VERSUM Master. (menu 20-1)
    Service
    Identification
    Password
    IR Address 001
    Common Address 000
    Serial Communication
    I2C Diagnosis
    Back
    Menu 20-1
    20.2 Cine VERSUM Master Identification
    How to select the Identification menu
    1. Select itemIDENTIFICATIONby rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
    2. Press the selection wheel on the Master or the key ENTER on the Remote Control to confirm.
    The sub menu IDENTIFICATION appears on-screen and in the graphical display, including a list of general information about the
    Cine VERSUM Master. (menu 20-2)
    Identification
    Cine VERSUM Master
    IR Address: 1
    Soft version: 2.0
    Baudrate PC: 115200
    Serial no: 0123456
    Run time: 135h
    Link Time
    Jul 17 2002
    11:51:28
    Back
    Menu 20-2
    R5976468 CINE VERSUM SYSTEM 03112003139 
    						
    							20. Cine VERSUM Master Settings & Info
    Explanation about the identification items
    The identification menu shows the general information of the Cine VERSUM Master status.
    • IR Address: typical address of the Cine VERSUM Master, to be used by the Remote Control to allow communication.
    • Soft Version: the loaded software version. This version number can be useful when calling for service assistance.
    • Baudrate PC: transfer speed for communication with an IBM PC (or compatible) or MAC. The baudrate must be the same as
    the baudrate of the connected computer.
    • Serial no: the fabrication number of the Cine VERSUM Master. This number can be useful when calling for service assistance.
    • Run Time: total run time since the first start up.
    • Link Time: below Link Time item, the creation date and time of the loaded software is shown.
    20.3 Cine VERSUM Master Password
    How to activate the password protection
    To prevent user’s modify system set ups, entering the service and installation menu can be password protected. Follow next steps:
    1. Select itemPASSWORDin the Service menu by rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
    2. Press the jog dial on the Master or the key ENTER on the Remote Control to confirm.
    The sub menu PASSWORD appears on-screen and in the graphical display, including the activation, Yes or No, of the password
    function and the possibility to change the password (4 digits). (menu 20-3)
    3. Select item USE PASSWORD [No] by rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
    The status of the password function is indicated between brackets. To change the status, continue with step 4.
    4. Press the jog dial on the Master or the keyENTERon the Remote Control to change the status from Yes to No and back.
    Status [Yes]: entering the Installation as well as the service menu is password protected (after the Cine VERSUM System has
    been shut down and restarted).
    Status [No]: Installation and Service menu are accessible all the time.
    5. Press the keyEXITon the Remote Control or select Back in the graphical display by rotating the jog dial on the Master followed
    by pressing the jog dial to confirm, to return.
    Password
    Use Password: [No]
    Modify Password
    Back
    Menu 20-3
    140R5976468 CINE VERSUM SYSTEM 03112003 
    						
    							20. Cine VERSUM Master Settings & Info
    How to change the password
    1. Select itemMODIFY PASSWORDby rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
    2. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    The sub menu NEW PASSWORD appears on-screen and in the graphical display, including the possibility to enter 4 digits,
    composing the new password. (menu 20-4)
    3. Start with filling in the new name, (Always 4 characters) as follows:
    - Pressing the cursor keys←or→on the Remote Control or pressing the jog dial on the Master allows to select the character
    position (moving to the right).
    - Pressing the cursor keys↑or↓on the Remote Control or rotating the jog dial on the Master allows to change the character (
    Numeric characters can be entered remotely with the numeric keys on the Remote Control).
    4. When the last character of the new password has been entered, the system returns to preceding menu.
    5. PressEXITon the Remote Control or select BACK in the graphical display menu, rotating the jog dial to select and pressing to
    confirm, to leave the menu mode.
    New Password
    Enter new value
    ----
    Menu 20-4
    20.4 Cine VERSUM Master Address
    Overview
    • About the Cine VERSUM Master Address
    • Cine VERSUM Master Address change
    • Selecting the Transmission Speed
    • Selecting the Interface standard (RS232/RS422)
    • RS422 data bus termination
    • Diagnosis
    20.4.1 About the Cine VERSUM Master Address
    Common address
    The common address of the Cine VERSUM Master is 0 or 1, and is selectable in the Service menu. That means that all commands
    from the Remote Control, programmed with address 0 or 1, will be executed by the Cine VERSUM Master.
    Individual address
    In addition to the common address, an individual address can be set up in the Cine VERSUM Master, in case e.g. more units are
    located in the same location. In this way, the units can be addressed individually.
    The individual address can be set in the Service mode and the address number to be set depends on used control device (Remote
    Control or PC).
    • Addresses between 0 and 9: control device is the IR Remote Control
    1
    • Addresses between 0 and 255: control device is an IBM PC (or compatible), Apple, Mac, etc..
    1. .
    R5976468 CINE VERSUM SYSTEM 03112003141 
    						
    							20. Cine VERSUM Master Settings & Info
    Reading out the stored address in the Cine VERSUM Master
    • Point the front of the Remote Control at the IR sensor of the Cine VERSUM Master.
    • Press the address key on the Remote Control.
    Image 20-1
    • A text box appears on-screen and in the graphical display on the Cine VERSUM Master indicating the stored address.
    MESSAGE
    IR Address: 1
    Menu 20-5
    20.4.2 Cine VERSUM Master Address change
    How to change the IR Address
    The IR address of the Cine VERSUM Master can be composed of3 numbers. Due to the limits of the Remote Control, values
    between 000 and 009 can be entered only. In case of PC control, values between 000 and 255 can be entered.
    1. Select itemIR ADDRESSin the Service menu by rotating the jog dial on the Master or the↑or↓keys on theRemote Control.
    2. Press the jog dial on the Master or the key ENTER on the Remote Control to confirm.
    The sub menu IR ADDRESS appears on-screen and in the graphical display, including the possibility to enter 3 digits, composing
    the new IR Address. (menu 20-6)
    3. Press the cursor keys←or→on the Remote Control or press the jog dial on the Master to select the last digit.
    4. Pressing the cursor keys↑or↓on the Remote Control or rotating the jog diall on the Master allows to change the character (
    Numeric characters can be entered remotely with the numeric keys on the Remote Control).
    When the address number has been entered, system returns to service menu.
    5. PressEXITon the Remote Control or selectBACKin the graphical display menu, rotating the jog dial to select and pressing to
    confirm, to exit the GUI.
    IR Address
    Enter New Value
    001
    Menu 20-6
    142R5976468 CINE VERSUM SYSTEM 03112003 
    						
    							20. Cine VERSUM Master Settings & Info
    20.4.3 Selecting the Transmission Speed
    How to set the transmission speed of the RS232 connection
    1. Select itemSERIAL COMMUNICATIONin the Service menu by rotating the jog dial on the Master or the↑or↓keys on the
    Remote Control.
    2. Press the jog dial on the Master or the key ENTER on the Remote Control to confirm.
    The sub menu SERIAL COMMUNICATION appears on-screen and in thegraphical display, including the possibility to set the
    Baudrate (transmission speed), the Interface standard RS232/RS422 and the RS422 termination. (menu 20-7)
    3. Select itemBAUDRATEin the Serial Communication menu by rotating the jog dial on the Master or the↑or↓keys on the Remote
    Control.
    4. Press the jog dial on the Master or theENTERkey on the Remote Control to change the Baudrate value between brackets.
    Note:Make sure that both the projector and the computer are set for the same Baud rate. Refer to the computer’s operation
    manual for instructions for setting the Baudrate.
    5. PressEXITon the Remote Control or selectBACKin the graphical display menu, rotating the jog dial to select and pressing to
    confirm, to exit the GUI.
    Serial Communication
    Baudrate [115200]
    Interface: [RS232]
    Termination: [On]
    Back
    Menu 20-7
    20.4.4 Selecting the Interface standard (RS232/RS422)
    About Data Transmission
    Standards have been developed to insure compatibility between units provided by different manufacturers, and to allow for reason-
    able success in transferring data over specified distances and/or data rates.
    RS232: Single-ended Data Transmission. The specification allows for data transmission from one transmitter to one receiver at
    relatively slow rates (up to 20K bits/second) and short distances (up to 50Ft.@ the maximum data rate).
    RS422: Differential Data Transmission: This standard was designed for greater distances and higher Baud rates. Data rates of up
    to 100K bits/second and distances up to 4000Ft. can be accommodated with RS422.
    How to set the interface standard
    Refer to the manual of the connected control unit about the data transmission standard to be set.
    1. Select itemINTERFACEin the Serial Communication menu by rotating the jog dial on the Master or the↑or↓keys on the Remote
    Control (Selecting the Transmission Speed, page 143.). (menu 20-8)
    2. Press the jog dial on the Master or theENTERkey on the Remote Control to change the Interface standard between brackets
    to RS232 or RS422.
    3. PressEXITon the Remote Control or selectBACKin the graphical display menu, rotating the jog dial to select and pressing to
    confirm, to exit the GUI.
    Serial Communication
    Baudrate [115200]
    Interface: [RS232]
    Termination: [On]
    Back
    Menu 20-8
    R5976468 CINE VERSUM SYSTEM 03112003143 
    						
    							20. Cine VERSUM Master Settings & Info
    20.4.5 RS422 data bus termination
    How to terminate the RS422 data bus
    The last control unit on the RS422 data bus has to be terminated.
    1. Select itemTERMINATIONin the Serial Communication menu by rotating the jog dial on the Master or the↑or↓keys on the
    Remote Control (Selecting the Transmission Speed, page 143.). (menu 20-9)
    2. Press the jog dial on the Master or theENTERkeyontheRemoteControltosettheterminationtoON.
    3. PressEXITon the Remote Control or selectBACKin the graphical display menu, rotating the jog dial to select and pressing to
    confirm, to exit the GUI.
    Serial Communication
    Baudrate [115200]
    Interface: [RS232]
    Termination: [On]
    Back
    Menu 20-9
    20.4.6 Diagnosis
    How to interpret the diagnosis table
    The diagnosis menu includes a list of I2C controlled IC’s. Seven locations are mentioned in the table with the respective address
    (Hex code), followed by 3 plus signs. The significance of the plus signs is referred to the data communication between the I2C
    controlled IC’s, in order write – read – acknowledge.
    If one of the communication parameters is not available, then the respective plus sign is replaced by a minus sign. This info can be
    useful for the technician if you call for technical assistance.
    How to enter the diagnosis menu
    1. Select itemI2C DIAGNOSISin the Service menu by rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
    2. Press the jog dial on the Master or the key ENTER on the Remote Control to confirm.
    The Diagnosis table appears on-screen and in the graphical display. (menu 20-10)
    3. PressEXITon the Remote Control or selectBACKin the graphical display menu, rotating the jog dial to select and pressing to
    confirm, to exit the GUI.
    Diagnosis
    INPUT SELECT 74H +++
    INPUT SELECT e0H +++
    INPUT SELECT e2H +++
    INPUT SELECT e4H +++
    LOCAL CTRL__ ecH +++
    PMP_________ 4aH +++
    LCD DISPLAY_ 7aH +++
    Back
    Menu 20-10
    144R5976468 CINE VERSUM SYSTEM 03112003 
    						
    							21. Maintenance Indicators
    21. MAINTENANCE INDICATORS
    Overview
    • Display Information
    • Display Diagnosis
    • ColorWheel IndexCine VERSUM 80
    • Test Pattern
    21.1 Display Information
    What info is displayed
    InstallationInput Slots
    File Service
    Display List
    Internal Pattern
    W hen no signal
    Source Transition
    OSD configuration
    Language
    Keystone
    Global Keystone:Yes
    Output: [Largest]
    Default Input Balance
    Back
    Display InfoSerial nr: 25416345
    Type: CineVERSUM 50
    Date: xx/xx/xx
    Temperature: 52
    Runtime: 87h
    Software: 2.0
    Firmware:
       Deserializer: 1
       Interface: 01.01
    Back
    Cine VERSUM r01
    Display List1 CV50  On
    2 CV120 On
    3 CV80 On
    Back
    Main Menu/Installation/Display List/Display Settings/Display Info
    Display Settings Switch OFF
     Display Info
     Rename
     IR Address 009
     Diagnosis
    Back
    Cine VERSUM 50
    Display Settings Switch OFF
     Display Info
     Rename
     IR Address 009
     Diagnosis
     CW  Index
     Orientation
     Test patterns
    Back
    Cine VERSUM 80
    Display Settings Switch OFF
     Display Info
     Rename
     IR Address 009
     Diagnosis
     Orientation
     Test patterns
     Lens
     Lamp
    Back
    Cine VERSUM 120
    Display Info
     Serial nr: 25416345
     Type: CineVERSUM 80
     Date: xx/xx/xx
     Temperature: 52
     Runtime: 87h
     Software: 3.0
     Firmware:
       Deserializer: 1
     Formatter: 65 67 5 88
     Lamp Type: 1
     CW -ID:55
     Runtime
     Lamp History
    Back
    Display Info Serial nr: 25416345
     Type: CineVERSUM 120
     Date: xx/xx/xx
     Temperature: 52
     Runtime: 87h
     Software: 3.0
     Firmware:
       Deserializer: 1
     Formatters
     Lamp run time: 50
     Lamp History
    Back
    Run TimesDisplay
     Total:197 h
    Lamp
     Total: 195 h
     55: 6 h
    Colorwheel
     Total: 163
     35-45: 3 h
     45-50: 10 h
     50-55: 21 h
     >55: 4 h
    Back
    Lamp History  Current
      2: - - -
      3: - - -
      4: - - -
      5: - - -
      6: - - -
      7: - - -
      8: - - -
      9: - - -
      Add lamp
      Reset History
    Back
    New lamp serial Nr  Enter new value
       _ _ _ _ _ _ _  _
         Add Lamp Add lamp to history
       No
       Yes
      Reset History  Are you sure?
        No
        Yes
    Lamp History  Current
      2: - - -
      3: - - -
      4: - - -
      5: - - -
      6: - - -
      7: - - -
      8: - - -
      9: - - -
     Reset History
    Back
      Reset History  Are you sure?
        No
        Yes
      Formatters       Red
           Green
           Blue
     Back
      Formatter Info     Config:        
         Degamma: 
         Main:               Sequence:  Back
    Image 21-1
    Display info for Cine VERSUM Master – Cine VERSUM 80 and Cine VERSUM 120
    Dependent on the selected display in the DISPLAY LIST menu, specific info is displayed on-screen and in the graphical display on
    the Cine VERSUM Master when selecting DISPLAY INFO in the Display settings menu.
    Explanation of the items
    Common for Cine VERSUM 50 – Cine VERSUM 80 and Cine VERSUM 120
    Serial numberSerial number of the display
    Ty p eKind of the display
    DateDate of fabrication
    TemperatureInside temperature
    R5976468 CINE VERSUM SYSTEM 03112003145 
    						
    							21. Maintenance Indicators
    Common for Cine VERSUM 50 – Cine VERSUM 80 and Cine VERSUM 120
    RuntimeTotal operation time of the display
    SoftwareInstalled software
    DeserializerConverts the serial data into parallel data
    For Cine VERSUM 80 only
    FormatterSerial number
    Lamp typeKind of the display
    Color Wheel IDColor wheel identification number
    RuntimeVia sub menu info about lamp run time and Color wheel run time, split up in ranges of
    temperature. .
    Lamp HistoryLamp history is kept up to date in the lamp history table. Via sub menu the possibility to add
    a new lamp and to reset the lamp history.
    When selecting ’Current’ in the lamp history table, lamp run time of the built-in lamp is shown.
    For Cine VERSUM 120 only
    FormattersVia sub menu info about the formatter for Red, Green and Blue.
    Lamp run timeTotal time of the lamp operation time.
    Lamp HistoryLamp history is kept up to date in the lamp history table. Via sub menu the possibility
    to reset the lamp history.
    When selecting ’Current’ in the lamp history table, lamp run time of the built-in lamp is shown.
    For Cine VERSUM 50 only
    InterfaceVersion number
    Due to rounding errors, the sum of hours in the Run times table is not always equal.
    146R5976468 CINE VERSUM SYSTEM 03112003 
    						
    All Barco manuals Comments (0)

    Related Manuals for Barco Projector Cineversum 80 Quickstart Manual